Architecture Commons^™

Barriers To Use Of Cross-Laminated Timber In Maine, Shane R. O'Neill

Forest Resources Faculty Scholarship

To increase understanding of both the adoption rate and in-state manufacturing of mass timber In Maine, the 131^st Legislature and Governor Mills passed LD 881, a resolve directing a study of the barriers facing cross-laminated timber In Maine and provide recommendations to promote their use in construction. This study was developed in response to the resolve. The study engaged 108 unique participants to define available training, education, and experiences across the stakeholders throughout the building lifecycle process in the state.

From this information, the following five recommendations are proposed:

1. Understand the policies and initiatives of other states to develop …

A Spike-Shaped Anchorage For Steel Reinforced Polymer (Srp)-Strengthened Concrete Structures, Xingxing Zou, Keenan L. Mcburney, Lesley H. Sneed

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Steel reinforced polymer (SRP) composite has recently emerged as an effective and economical solution for strengthening of reinforced concrete (RC) structures. Premature debonding failure of unanchored SRP at low load levels generally governs the performance of RC structures strengthened with externally bonded SRP. Therefore, a novel yet simple spike-shaped anchorage system was proposed in this study to prevent the debonding failure of SRP and to improve the interfacial shear capacity. Experimental investigation through single-lap shear tests of SRP-concrete joints showed that the anchorage system changed the failure mode from composite debonding to fiber rupture. In addition, the anchorage system substantially …

Precious Plastics - Plastic Brick Machine Fabrication, Timothy Ukaobasi Kanu, Evi Paraskevi Troulis

Architectural Engineering

The goal of this research is to determine the structural parameters of the recycled plastic polypropylene when molded into bricks resembling CMU blocks. To accomplish this, three mechanisms had to be assembled: the shredder, the injector, and the 1x1 mold. A tensile and compression test were to be performed on the plastic brick, and the values would be used to compare the tensile and compressive strength of PP plastic bricks, as well as their modulus of elasticity and stress vs. Strain performance. These values would be analyzed to determine whether it would be feasible to build an entire plastic wall. …

Reduction Of Embodied Carbon In Buildings Through Use Of Low Carbon Strategies And Standardization And Enforcement Of Life Cycle Assessment, Bhargavi Sai Sudhakar

Master's Projects and Capstones

The building and construction industry is energy intensive and as of 2021, this industry is responsible for 37% of the total global greenhouse gas emissions. In previous studies of conventional buildings, the operational energy of a building contributed to 80% and the embodied energy contributed to 20% of the total life cycle energy. With increase in policies and standards that focus on reducing the operational energy, low energy and certified green buildings have emerged where the operational energy has considerably reduced. The relative and absolute share of embodied energy in these energy efficient buildings have increased due to excessive use …

A Review Of Current Construction Guidelines To Inform The Design Of Rammed Earth Houses In Seismically Active Zones, David Thompson, Charles Augarde, Juan Pablo Osorio

Articles

Sustainability in the materials we use for construction is a prime concern, focusing on reducing the embodied energy and carbon footprints of the materials used. The cement used in concrete products is responsible for a significant proportion of Man's CO2 emissions and its production requires substantial energy input, as do fired clay products. For this reason, products formed from unfired earthen materials are of increasing interest and the current challenges include devising means of robust design for strength and to address durability concerns. One form of earthen construction that employs an in-situ method is rammed earth, and it is a …

Assessment Of Carbon Dioxide Emission And Its Impact On High-Rise Mixed-Use Buildings In Egypt, Ahmed Salah Hamza

Theses and Dissertations

With Egypt's vision of 2030 focusing on sustainable development with a true emphasis on Carbon Dioxide (CO₂) emission reduction in the newly built cities and high-rise buildings, efforts are exerted on various levels towards accomplishing the vision’s goals. This is achieved through multiple tools and models associated with aiding the reduction of carbon emissions, yet not a clear one was introduced for the mixed-use buildings in Egypt.

Through this work, a significant gap was identified with respect to high-rise buildings carbon emission assessment in Egypt. This was a main driving force for this work in an attempt to …

Use Of Biomimicry Design Approach In Constructing Sustainable Resilient Structures (Case Study: Port Of Beirut), Farouk Bader, Marwan Halabi, Hiba Mohsen, Maged Youssef

BAU Journal - Creative Sustainable Development

Resiliency is not the same as sustainability, nor its substitute, but definitely the two concepts complement each other’s. Sustainability is the avoidance of depletion of natural resources to maintain ecological balance whereas resiliency is to recover, adapt and keep going in the face of setbacks. While designing with green approach is important but what will happen to leed points if the building becomes uninhabitable due to disasters, that’s where resiliency comes into play. The 2019 statistics showed that natural disasters accounted for 133 billion dollars losses and manmade ones accounted for other 7 billion in addition to 11,755 people worldwide …

Computational Design Of Nonlinear Stress-Strain Of Isotropic Materials, Askhad M.Polatov, Akhmat M. Ikramov, Daniyarbek Razmukhamedov

Chemical Technology, Control and Management

The article deals with the problems of numerical modeling of nonlinear physical processes of the stress-strain state of structural elements. An elastoplastic medium of a homogeneous solid material is investigated. The results of computational experiments on the study of the process of physically nonlinear deformation of isotropic elements of three-dimensional structures with a system of one- and double-periodic spherical cavities under uniaxial compression are presented. The influence and mutual influence of stress concentrators in the form of spherical cavities, vertically located two cavities and a horizontally located system of two cavities on the deformation of the structure are investigated. Numerical …

Comparing The Environmental Impacts Of Using Mass Timber And Structural Steel, Khang Hoang Nguyen, Steelee Knight Morgan

Construction Management

Although mass timber has seen a gradual rise in demand in the past, there has been a lack of extensive research on the environmental impacts of using mass timber as a primary structural framing material. This paper compares structural steel, and mass timber’s total embodied carbon emissions. Accurate estimates were made using plans and specs for different projects retrieved from semi-structured interviews. The estimates were input through the EC3 Calculator to provide extensive total carbon emissions measurements between each construction material. Using structural steel framing increased the project’s overall environmental impact by roughly 84% compared to using mass timber. The …

Analysis Of Burning Wood In The Transient State And The Application To Structural Design, Roberta Veliz, Kimberly Guzman

Architectural Engineering

Determining the extent of the contribution of exposed timber on compartment fire dynamics in open floor plans is a complex process. Designers traditionally used compartmentalization design methods which create spaces where flashover is likely, given the fuel load and ventilation conditions. However, due to the large geometric dimensions and spread of fuel, fires in open floor plans are more likely to remain as localized or traveling fires. As such, an understanding of not only ignition potential but also flame spread is critical to characterizing the contribution of exposed timber. An integral step in characterizing the potential contribution is through an …

Mandela Splash Pad Pre-Construction Plan, Levi Sandbulte

Theses/Capstones/Creative Projects

In the construction industry, it is the responsibility of the general contractor to take the architect’s ideas and turn it into a real building. Many times this requires ample communication and several drafts. This efficient execution of this process is vital to the completion of a successful project. In this project, I practice this communication process. The challenge presented by the owner is to build an affordable splash pad, and without impacting the construction schedule of the Early Childhood Development Center (ECDC) that is being built on the same property at the same time. This proposal gives the owner a …

Northeastern Species In Hybrid Cross Laminated Timber, Hamid Kaboli

Doctoral Dissertations

Known in the building industry throughout the world, Cross Laminated Timber (CLT) is a massive timber building material with outstanding structural, fire, and seismic properties. CLT is a cost-competitive, sustainable construction material is a good candidate as a substitute material for concrete, masonry, and steel, in mid-rise and high-rise buildings. CLT is perpendicular layers of dimensional lumbers usually laminated together and forming a massive structural panel. This dissertation explores the viability of utilizing Massachusetts grown Eastern Hemlock and Eastern White Pine in CLT panels as pure or in conjunction with other high-value wood products. 59% of Massachusetts’ lands are covered …

Latex Modified Concrete - Very Early Strength, Bobby Steele

Purdue Road School

INDOT came out with specifications for a very early strength concrete to use on bridge deck overlays. This concrete is fast setting, which allows overlays to be performed over a weekend and benefits the traveling public with a short duration of traffic interference. Cure time to reach the strength requirement is 3 hours. E&B Paving performed the first application with the new spec on August 26, 2018. Many changes were also made to the INDOT Specification Section 722.

High Performance Mortar With 100% Recycled Aggregate Using Titanium Dioxide Nanoparticles, Molly Schrager, Vito Francioso, Arjun Kadakia, Mirian Velay-Lizancos

The Summer Undergraduate Research Fellowship (SURF) Symposium

Concrete and mortar are materials commonly used in construction. Their main compounds are cement, aggregates (sand and gravel) and water. In an effort to increase the sustainability of these materials, the idea of using recycled aggregates from ground old concrete and using it to make mortar and concrete has gained more interest. It has two advantages: it reduces the need to mine for raw materials and lessens the amount of old and defective concrete that is typically put in landfills. But, the use of recycled concrete aggregate lowers the strength of mortars and concretes because the residual compounds in the …

Direct Strength Approach To Predict The Flexural Strength Of Cold-Formed Z-Section Purlins On Sloped Roofs, Ali Parva, Michael W. Seek

Engineering Technology Faculty Publications

In this study, the strength of cold-formed Z-section purlins is predicted considering the effects of roof slope in real roof systems. The study applies to simple span purlins with torsion restraints at support locations and at paired locations along the length of the member. A previously developed method has shown through comparisons to base tests that when the biaxial bending and torsion stresses are incorporated into the analysis, the Direct Strength Method can accurately predict the strength of a purlin. These stress distributions can deviate substantially from the constrained bending approximation typically assumed in analysis and therefore impacts the local …

Lateral Strength And Ductile Behavior Of A Mortise-Tenon Connected Timber Frame, Alexandros Kouromenos

Master's Theses

The primary goals of this project were to examine the amount of lateral force resisted by a single-bay mortise-tenon connected timber moment frame, and to introduce ductile behavior into the mortise-tenon connections by adding a steel sleeve around a traditional wood peg. This research aimed to provide proof that traditional timber frames are capable of ductile racking while reliably complying with ASCE 7-10 building code drift speci! cations, implying an increase in the ASCE 7-10 ductility factor (R) for wood frames when used as lateral force resisting elements. A secondary goal was to promote traditional heavy timber framing as a …

Compact Facility For Testing Steady And Transient Thermal Performance Of Building Walls, Aimee Byrne, Gerard Byrne, Anthony Robinson

Articles

Energy efficiency retrofit of buildings represents a key effort in reducing EU energy demand by 20% by 2020. However, predictions tend to overestimate savings by large percentages. The shortfall in savings can be attributed to incorrect predictive techniques, comfort takeback along with other behavioural and workmanship variables. Common predictive techniques related to heat loss tend to be based on the U-value of the building envelope. This paper presents the design of a more straightforward and compact version of the traditional Hot-Box apparatus (measures U-value) which instead determines the thermal resistance of samples of building envelope. U-value includes the need to …

Seeing Red: Characterizing Historic Bricks At Sylvester Manor, Long Island, Ny 1652-1735, Martin John Schmidheiny

Graduate Masters Theses

The goal of this project is to develop a basic material characterization of the bricks excavated at the site of Sylvester Manor on Shelter Island, New York. In the early Manor period of 1650-1690, this early Northern provisioning plantation supplied Barbadian sugar operations and pursued mercantile interests independent of state control. Accounting for the range of production defects and material characteristics of the bricks suggests on-site or local manufacture as a regional ceramic industry developed. Qualitative visual analysis and petrographic thin-sections were used to characterize the internal composition, variation and production evidence in the bricks. Interpreting the results of this …

Compression Testing And Failure Modes Of Steel-Concrete Composite (Sc) Structures For Nuclear Containment, Patrick Michael Wanamaker, Amit H. Varma

The Summer Undergraduate Research Fellowship (SURF) Symposium

Although being able to provide much cleaner power than burning coal and other fossil fuels, nuclear power plants are still a tough sell to the general public due to their history of being spontaneously dangerous. The containment structures surrounding these nuclear plants, however, can play a huge role in reducing the risks associated with them. Relatively new designs for these containment assemblies, known as SC (steel-concrete composite) structures, aim to increase the strength and durability of the containment facilities while keeping costs down. By varying the spacing between shear studs, the ratio of concrete to steel, and the ratio of …

Materials Education And Research In Art And Design: A New Role For Libraries (Website), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Program Sheet), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Program Booklet), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Survey Stats), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Collection Creation And Administration: A New Role For Libraries (White Paper), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

The Problem/Opportunity: To define, identify, and guide design-based materials collections in academic settings and foster community among those with existing collections and/or those considering creating and supporting one.

Contents and topics:

1. What is a materials collection?
2. Why have a materials collection?
3. Acquisition strategies
4. Organizational approaches
5. Programming possibilities
6. Symposium summary
7. Resources

Vulnerability Of Progressive Collapse In Reinforced Concrete Flat-Plate Buildings, Jinrong Liu

College of Engineering: Graduate Celebration Programs

• Progressive collapse is the spread of initial local failure, causing partial or
  even total collapse of a building.
• Flat plate structure is widely used for office and residential buildings.
• There is a large inventory of older flat plate building without continuous slab bottom reinforcement through columns.
• Limited knowledge exists regarding the risk of disproportionate collapse in
  older flat-plates under sudden column removal during abnormal events.
• Reliable mechanical model is needed for structural evaluation.

Quantum Man, Julian Voss-Andreae

The STEAM Journal

According to quantum physics, the world is fundamentally quite different than it seems. Drawing inspiration from the underlying nature of reality, former quantum physicist Julian Voss-Andreae created an image of a walking human as a quantum object. Made up of parallel sheets of steel, the sculpture is a metaphor for the counter-intuitive world of quantum physics. Symbolizing the dual nature of matter with the appearance of classical reality on the surface and cloudy quantum behavior underneath, the sculpture seems to consist of solid steel when seen from the front, but dissolves into almost nothing when seen from the side.

Design And Performance Of Load Bearing Shear Walls Made From Composite Rice Straw Blocks, Kevin Robert Camann

Master's Theses

Although rice straw and other grains have been used in building since pre-history, in the past two decades, there has been a move to utilize this rapidly renewable, locally available, agricultural byproduct as part of the sustainable construction movement. Up to this point, this has been done by simply stacking up the full straw bales. Stak Block, invented by Oryzatech, Inc., is a modular, interlocking block made of a composite of rice straw and binding agent that serves as an evolution in straw construction. This study investigates the feasibility of using these Stak Blocks as a structural system. The report …

Damage Characterization Of Beam-Column Joints Reinforced With Gfrp Under Reversed Cyclic Loading, Aly M. Said

Civil and Environmental Engineering and Construction Faculty Research

The use of fiber reinforced polymer (FRP) reinforcement in concrete structures has been on the rise due to its advantages over conventional steel reinforcement such as corrosion. Reinforcing steel corrosion has been the primary cause of deterioration of reinforced concrete (RC) structures, resulting in tremendous annual repair costs. One application of FRP reinforcement to be further explored is its use in RC frames. Nonetheless, due to FRP's inherently elastic behavior, FRP-reinforced (FRP-RC) members exhibit low ductility and energy dissipation as well as different damage mechanisms. Furthermore, current design standards for FRP-RC structures do not address seismic design in which the …

Behaviour Of Reinforced Self-Consolidating Concrete Frames, Aly Said, Moncef Nehdi

Civil and Environmental Engineering and Construction Faculty Research

Multi-storey reinforced concrete (RC) structural frames represent some of the most congested structural elements. Placing and consolidating concrete in such structural frames imposes substantial challenges. This offers a unique area of application for self-consolidating concrete (SCC) because of its inherent ability to flow under its own weight and fill congested sections, complicated formwork and hard-to-reach areas. Research is, however, needed to demonstrate the ability of SCC structural frames adequately to resist vertical and lateral loads. In the present study, full-scale 3 m high beam-column joints reinforced as per the Canadian Standards CSA A23·3-94 and ACI-352R-02 were made with normal concrete …

Miami Furniture Study, Center For Economic Development

Center for Economic Development Technical Reports

This research project, under the guidance of Dr. John Mullin and Professor Zenia Kotval, sought to study and examine Miami's fledgling furniture cluster as well as key elements of the American furniture industry. I believe that this report presents an honest unbiased "snapshot" of the American furniture industry and the City of Miami's furniture design district. All of the information contained within this report has been cited and referenced to the best of my ability.