Digital Commons Network^™

Update To Ansi/Ans-6.4.3-1991 For Low-Z And Compound Materials And Review Of Particle Transport Theory, Luis Durani

UNLV Theses, Dissertations, Professional Papers, and Capstones

The ANSI/ANS-6.4.3-1991 Gamma-Ray Attenuation Coefficients and Buildup Factors for Engineering Materials Standard (herein known as ANS Standard), contains derived gamma-ray attenuation coefficients and buildup factors for selected engineering materials and elements for use in shielding calculations (ANSI/ANS-6.1.1, 1991). The current status of the ANS Standard is withdrawn due to the lack of any updates since its last publication. Since the last update of the ANS standard, more accurate codes for particle transport and cross sectional data have become available. As a result, this study was carried out to update gamma-ray buildup factors for iron and water as a function of …

Two-Tank Indirect Thermal Storage Designs For Solar Parabolic Trough Power Plants, Joseph E. Kopp

UNLV Theses, Dissertations, Professional Papers, and Capstones

The performance of a solar thermal parabolic trough plant with thermal storage is dependent upon the arrangement of the heat exchangers that ultimately transfer energy from the sun into steam. The steam is utilized in a traditional Rankine cycle power plant. The most commercially accepted thermal storage design is an indirect two-tank molten salt storage system where molten salt interacts with the solar field heat transfer fluid (HTF) through a heat exchanger. The molten salt remains in a closed loop with the HTF and the HTF is the heat source for steam generation. An alternate indirect two tank molten salt …

Fracture Toughness, Crack-Growth-Rate And Creep Studies Of Alloy 276, Joydepp Pal

UNLV Theses, Dissertations, Professional Papers, and Capstones

Austenitic nickel-base Alloy 276 had been proposed to be a candidate structural material within the purview of the nuclear hydrogen initiative program. A mechanistic understanding of high temperature tensile deformation of this alloy has already been presented in an earlier investigation. The current investigation has been focused on the evaluation of crack-growth behavior, fracture toughness, stress-corrosion-cracking and creep deformation of this alloy as functions of different metallurgical and mechanical variables. The results of crack-growth study under cyclic loading indicate that this alloy exhibited greater cracking tendency with increasing temperature at a constant load ratio (R). However, the effect of temperature …

Study Of Corrosion Of Materials In The Sulfur-Iodine Hydrogen Production Cycle, Thao Trung Ho

UNLV Theses, Dissertations, Professional Papers, and Capstones

Hydrogen is of great interest since the availability of traditional fossil fuels is in decline. Strictly speaking, hydrogen is not a primary source of energy but is an energy carrier, since energy typically must be used from another source (electricity, natural gas, coal, etc.) to produce it. Of hydrogen production techniques, the Sulfur-Iodine thermochemical water splitting process (S-I cycle), which was proposed by General Atomics (GA), is promising with its simplicity and high efficiency. Most of the chemicals are recycled except water. However, the S-I cycle operates in a harsh, corrosive environment in the presence of a mixture of iodine …

Studying The Impacts Of Primary Incidents On Freeways To Identify Secondary Incidents, Rohit Reddy Saddi

UNLV Theses, Dissertations, Professional Papers, and Capstones

Freeway incidents are associated with different impacts such as traffic congestion, delays, fuel consumption, secondary incidents etc. Secondary incidents are caused due to primary incidents and require the same personnel who are already engaged. This thesis studies various impacts caused by primary incident in space and time occurring on the freeways and these results are applied to identify secondary incidents. Three types of impacts are identified and proposed in this study. Dynamic nature of queue length in the direction of accident is studied. Dynamic nature of congestion in the opposite direction of the freeway till the accident is cleared is …

Substituent Effect On The Electronic And Assembling Properties Of Asymmetric Phenazine Derivatives, Bin Cao

UNLV Theses, Dissertations, Professional Papers, and Capstones

Currently, one-dimensional (1-D) nanostructures have drawn much interest because of their potential applications for nanoscale optoelectronic devices. Self-assembly (SA) based on π-conjugated systems through various intermolecular interactions has been widely used to produce 1-D nanostructure. Morphology of the assembled structures can be modified by incorporating substituents, which provide additional secondary interactions. Meanwhile, those substituents also influence the electronic properties of the molecules. Previous studies have made little effort to systematically study subsistent effects on both electronic and SA properties.

The primary objective of this research is to generate controllable 1-D structures through SA, and to provide a fundamental understanding of …

Novel Techniques In Iris Recognition, David Walker

UNLV Theses, Dissertations, Professional Papers, and Capstones

Using Daugman's algorithm and comparable alternatives, we find that we are able to identify an iris with as little as less than half of the iris information available, and an equal error rate comparable with that of popular biometrics like the fingerprint and face recognition biometrics. Different experiments were done based on percentage of iris shown, the resolution of the iris, and the position of the iris covered to determine if partial iris recognition is a viable biometric. It was found after over 500,000 different iris comparisons amongst five different experiments that regardless of the model used and the resolution, …

Spectral Analysis Of Pathological Acoustic Speech Waveforms, Priyanka Medida

UNLV Theses, Dissertations, Professional Papers, and Capstones

Biomedical engineering is the application of engineering principles and techniques to the medical field. The design and problem solving skills of engineering are combined with medical and biological science, which improves medical disorder diagnosis and treatment. The purpose of this study is to develop an automated procedure for detecting excessive jitter in speech signals, which is useful for differentiating normal from pathologic speech. The fundamental motivation for this research is that tools are needed by speech pathologists and laryngologists for use in the early detection and treatment of laryngeal disorders. Acoustical analysis of speech was performed to analyze various features …

Optimization Of Solid Oxide Fuel Cell Interconnect Design, Krishna C. Pulagam

UNLV Theses, Dissertations, Professional Papers, and Capstones

Performance of solid oxide fuel cells (SOFC) is dependent of a set of complex physical and chemical processes occurring simultaneously. Interconnect for SOFC is important as it provides electrical connection between anode of one individual cell to the cathode of neighboring one. It also acts as a physical barrier to protect the air electrode material from the reducing environment of the fuel on the fuel electrode side, and it equally prevents the fuel electrode material from contacting with oxidizing atmosphere of the oxidant electrode side. A three-dimensional numerical model has been developed to evaluate the SOFC including the current collector, …

Experimental And Numerical Study Of A Proton Exchange Membrane Electrolyzer For Hydrogen Production, Sachin S. Deshmukh

UNLV Theses, Dissertations, Professional Papers, and Capstones

Hydrogen as a fuel source has received attention from researchers globally due to its potential to replace fossil based fuels for energy production. Research is being performed on hydrogen production, storage and utilization methods to make its use economically feasible relative to current energy sources. The PEM electrolyzer is used to produce hydrogen and oxygen using water and electricity. Focus of our study is to provide a benchmark experiment and numerical model of a single cell electrolyzer that can assist in improving the current state of understanding of this system. Parametric analysis of an experimental cell was performed to understand …

Tensile Strength And Failure Criterion Of Analog Lithophysal Rock, James A. Nott

UNLV Theses, Dissertations, Professional Papers, and Capstones

This project determines the tensile strength of lithophysal analog rock and presents failure criteria that can be used by geotechnical engineers to evaluate underground structures in rock. The physical and mechanical properties that are related to the failure criterion, such as porosity, compressive strength and modulus of elasticity, are also discussed. Experimental tensile tests were made using direct uniaxial and indirect Brazilian tests. Three 4-inch specimens were fabricated and tested in direct uniaxial tensile tests using Hydro-Stone TB. The results showed that the elastic tensile modulus of elasticity was within two percent of existing data for the compressive modulus of …

Analysis And Design Of Low Power Cmos Ultra Wideband Receiver, Abdul Bhuiyan

UNLV Theses, Dissertations, Professional Papers, and Capstones

This research concentrates on the design and analysis of low power ultra wideband receivers for Multiband Orthogonal Frequency Division Multiplexing systems. Low power design entails different performance tradeoffs, which are analyzed. Relationship among power consumption, achievable noise figure and linearity performance including distortion products (cross-modulation, inter-modulation and harmonic distortion) are derived. From these relationships, circuit design proceeds with allocation of gain among different sub circuit blocks for power optimum system.

A power optimum RF receiver front-end for MB-OFDM based UWB systems is designed that covers all the MB-OFDM spectrum between 3.1 GHZ to 9.6 GHZ. The receiver consists of a …

Effects Of Mechanical And Metallurgical Variables On Creep, Fracture Toughness And Crack Growth Behavior Of Alloy 617, Muhammad Hasibul Hasan

UNLV Theses, Dissertations, Professional Papers, and Capstones

Nickel base Alloy 617 has been identified to be a suitable structural material for heat exchanger applications in both hydrogen and electricity generation using nuclear heat. A maximum operating temperature of 950°C has been specified by department of energy (DOE) for both applications to achieve a maximum possible efficiency. Therefore, an extensive investigation has been pursued to evaluate time-dependent-deformation (Creep) of this alloy as functions of temperature and applied load. The results indicate that this alloy exhibited severe creep deformation, characterized by development of an instantaneous tertiary creep region at 850 and 950°C under applied stresses corresponding to its 35% …

Mitigation Of Impact Vibrations Using Impedance Mismatch In Cylindrical Structures, Sachiko Sueki

UNLV Theses, Dissertations, Professional Papers, and Capstones

The focus of this work is to study the phenomenon of material impedance mismatch to determine its effect on the mitigation of high frequency accelerations in projectile and long bar structures within linear ranges of materials. In this study, the acceleration responses of structures with various materials and material combinations were studied experimentally, numerically and by the Finite Element Analysis (FEA). Air-gun tests conducted by the US Army Research Laboratory were modeled using FEA to simulate the acceleration pulse and shock waves experienced by artillery components during a launch. After the prototype of projectile was selected, further studies were conducted …

Parametric Study Of Stimulus-Response Behavior Incorporating Vehicle Heterogeneity In Car-Following Models, Saidi Siuhi

UNLV Theses, Dissertations, Professional Papers, and Capstones

The objective of this study was to develop a family of car-following models that address the shortcomings of car-following models developed by General Motors (GM) in the 1950s. The developed models consist of separate models for acceleration, deceleration, and steady-state responses for congested freeway traffic conditions. The study calibrated the models using individual vehicle trajectory data collected on a segment of Interstate 101 in Los Angeles, California. Furthermore, the study validated the models using individual vehicle trajectory data collected on a segment of Interstate 80 in Emeryville, California. The study used nonlinear regression with robust standard errors to estimate the …

Evaluation Of Rapid Electric Battery Charging Techniques, Ronald Baroody

UNLV Theses, Dissertations, Professional Papers, and Capstones

Battery powered electric vehicles are gaining popularity worldwide. This is trend is driven by several factors including the need to reduce air and noise pollution, and dependence on fossil fuels. The main drawback of today's electric vehicle is its limited range, and the long time duration that is required to charge the electric batteries. This thesis addresses the latter problem.

In recent years, significant progress (through research and development) has been made to accelerate the charging time of the electric vehicle batteries through pulse charging rather than supplying continuous current and/or voltage. Some patented fast charging techniques demonstrated reduced charging …

Metal Induced Crystallization Of Silicon Thin Films, Sandeep Kumar Raju Sangaraju

UNLV Theses, Dissertations, Professional Papers, and Capstones

Low temperature crystallization of thin film silicon is important for many industrial applications including flat panel displays and silicon thin film solar cells. Unfortunately this remains a major challenge since crystallization temperature of silicon is above 1,000 degrees Celsius, thus limiting to substrates that can tolerate high temperatures. The inability to deposit crystalline thin films on glass substrates is the reason why flat panel display industry uses amorphous silicon for LCD active matrix displays. Thus the ability to deposit crystallized thin film silicon at low temperatures will have significant impact on thin film silicon applications. It has been observed that …

Islanded Operation Of A Distribution Feeder With Distributed Generation, Chandu Venu

UNLV Theses, Dissertations, Professional Papers, and Capstones

A distribution system that is equipped with distributed generators, such as roof-mounted photovoltaic systems, can operate as a microgrid (i.e., separated from the grid) under some specific conditions. A key feature of a microgrid is its ability to separate and isolate itself from the utility seamlessly with little or no disruption to the loads within the microgrid. Then, when the utility grid returns to normal, the microgrid automatically resynchronizes and reconnects itself to the grid, in an equally seamless manner. This thesis addresses the conditions necessary for proper microgrid operation: these include local generation-load mismatch, local energy storage, load switching, …

Design And Characterization Of A Shock And Vibration Mitigation Seat System, George Samaan Ladkany

UNLV Theses, Dissertations, Professional Papers, and Capstones

Extensive research has been conducted into the development of pneumatic seatbladder systems for shock and vibration mitigation for use in current U.S military vehicle envelopes. This research expands on the previous work through an elaborate experimental characterization of four prototype air bladder seat cushion systems. The experimental characterization conducted included shock testing, continuous vibration, and internal dynamic pressure measured during the shock event.

The shock testing was conducted both at the Army Research Lab as well at UNLV. The shock testing conducted at UNLV was performed on a drop tower designed and constructed during the time of this research. The …

Quantity-Based Cost Forecasting System For Street Construction Projects, Nipesh Pradhananga

UNLV Theses, Dissertations, Professional Papers, and Capstones

Construction projects typically are not withdrawn after going into the competitive bidding process. The decision of contracting authorities regarding which projects will proceed to the bidding stage depends, in part, upon the early estimates of probable cost. Efforts are made to make this estimate as realistic as possible. Irrespective of the estimate of probable cost, the actual project cost is established by the amount of the winning bid.

This study analyzed historical bid data of street construction projects undertaken by the Public Works Department, Clark County, Nevada, from 1991 through 2006. The focus of this study was on utilizing statistical …

Extents And Limits Of Radioscopic Detection Of Nuclear Materials In Cargo Containers With Two Megavoltage Energy Barriers, Vijay Kumar Mandava

UNLV Theses, Dissertations, Professional Papers, and Capstones

The megavoltage X-ray technology is utilized for detecting nuclear materials in cargo containers. Interlaced response is obtained by switching rapidly between 6MeV and 9 MeV beams. It is known that the ratio of penetration levels of cargo contents taken at nominal and dual energies provides the information about atomic numbers of materials, and thus can also indicate the threat group. However, the identification is not straightforward if combinations of materials are present. The latter can lead to misdetections. It is imperative to know what are the extent and the limit of the currently employed technology, and how to carry out …

Zirconia-Magnesia Inert Matrix Fuel And Waste Form: Synthesis, Characterization And Chemical Performance In An Advanced Fuel Cycle, Kiel Steven Holliday

UNLV Theses, Dissertations, Professional Papers, and Capstones

There is a significant buildup in plutonium stockpiles throughout the world, because of spent nuclear fuel and the dismantling of weapons. The radiotoxicity of this material and proliferation risk has led to a desire for destroying excess plutonium. To do this effectively, it must be fissioned in a reactor as part of a uranium free fuel to eliminate the generation of more plutonium. This requires an inert matrix to volumetrically dilute the fissile plutonium. Zirconia-magnesia dual phase ceramic has been demonstrated to be a favorable material for this task. It is neutron transparent, zirconia is chemically robust, magnesia has good …

Performance Evaluation Of Network-On-Chip Interconnect Architectures, Xinan Zhou

UNLV Theses, Dissertations, Professional Papers, and Capstones

With a communication design style, Network-on-Chips (NoCs) have been proposed as a new Multi-Processor System-on-Chip paradigm. Simulation and functional validation are essential to assess the correctness and performance of the NoC design. In this thesis, a cycle-accurate NoC simulation system in Verilog HDL is developed to evaluate the performance of various NoC architectures. First, a library of NoC components is developed based on an existing design. Each NoC architecture to be evaluated is constructed from the library according to the topology description which specifies the network topology, network size, and routing algorithm. The network performance of four NoC architectures under …

Optimal Design Of Discrete-Time Delta Sigma Modulators, Matthew Edward Jackson

UNLV Theses, Dissertations, Professional Papers, and Capstones

In this thesis, optimal signal transfer functions (STFs) and noise transfer functions (NTFs) for discrete time delta sigma (ΔΣ) modulators are determined. For a given oversampling rate (OSR), these STFs and NTFs are optimized with respect to a weighted combination of the ΔΣ modulator's signal-to-noise ratio (SNR) and dynamic range (DR). This optimization problem is solved using a novel hybrid orthogonal genetic (HOG) algorithm that uses customized genetic operators to improve algorithm performance and accuracy when applied to multimodal, non-differentiable performance surfaces. To generate optimal system functions, the HOG algorithm is implemented as a constrained global optimizer to minimize cost …