Physical Sciences and Mathematics Commons^™

Comparison In Factors Affecting Electrochemical Properties Of Thermal-Reduced Graphene Oxide For Supercapacitors, Peng Xiao, Da-Hui Wang, Jun-Wei Lang

Journal of Electrochemistry

In this paper, thermal-reduced graphene oxide (T-RGO) materials are synthesized by modified Hummer’s method, followed by thermal reduction under argon atmosphere at different temperatures. Electrochemical investigations show that, for T-RGO electrodes, good electrical conductivity is necessary and the surface functional groups play more significant role than the specific surface area in determining the electrochemical capacitance. The T-RGO obtained at 900 °C (T-RGO900) with a relatively high Brunauer-Emmett-Teller (BET) surface area (314 m²·g^-1) and a high electrical conductivity (2421 S·m^-1) shows a low specific capacitance of 56 F·g^-1. In comparison, the T-RGO obtained …

Electrostatic Force Microscopy And Electrical Isolation Of Etched Few-Layer Graphene Nano-Domains, D. Patrick Hunley, Abhishek Sundararajan, Mathias J. Boland, Douglas R. Strachan

Physics and Astronomy Faculty Publications

Nanostructured bi-layer graphene samples formed through catalytic etching are investigated with electrostatic force microscopy. The measurements and supporting computations show a variation in the microscopy signal for different nano-domains that are indicative of changes in capacitive coupling related to their small sizes. Abrupt capacitance variations detected across etch tracks indicates that the nano-domains have strong electrical isolation between them. Comparison of the measurements to a resistor-capacitor model indicates that the resistance between two bi-layer graphene regions separated by an approximately 10 nm wide etch track is greater than about 1×10¹² Ω with a corresponding gap resistivity greater than about …

Collective Edge Modes Near The Onset Of A Graphene Quantum Spin Hall State, Gunpathy Murthy, Efrat Shimshoni, H. A. Fertig

Physics and Astronomy Faculty Publications

Graphene subject to a strong, tilted magnetic field exhibits an insulator-metal transition tunable by tilt angle, attributed to the transition from a canted antiferromagnetic (CAF) to a ferromagnetic (FM) bulk state at filling factor ν=0. We develop a theoretical description for the spin and valley edge textures in the two phases, and the implied evolution in the nature of edge modes through the transition. In particular, we show that the CAF has gapless neutral modes in the bulk, but supports gapped charged edge modes. At the transition to the FM state the charged edge modes become gapless and are …

Kelvin Probe Force Microscopy On Graphene Thin Films For Solar Cell And Biosensing Applications, Faranak Sharifi

Electronic Thesis and Dissertation Repository

Graphene, a one atom thick planer sheet of carbon atoms, has attracted much attention in scientific and technological communities due to its remarkable electronic and physical properties. Graphene has been widely studied as an alternative to transparent conducting Indium Tin Oxide (ITO) electrodes in organic photovoltaics fabrication. Graphene platforms have also attracted interest in biological applications. However, large area graphene films are not yet widely commercialized because the fabrication techniques needed to prepare high quality graphene are expensive and non-scalable. More importantly, most of the low cost fabrication techniques require using toxic materials, which are not biocompatible for using graphene …

Preparation And Electrochemical Behavior Of Pbo/Gn/Ac, Yun-Fang Gao, Yan-Ping Wang, Qiu-Shi Yao, Fu-Hua Wang, Dong-Lei Ren, Xin Xu

Journal of Electrochemistry

The lead oxide/graphene/activated carbon (PbO/GN/AC) composite materials were prepared by impregnating commercial activated carbon and graphene in saturated lead nitrate solution followed by calcination. The structures and morphologies of the composite were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The results show that PbO crystals (about 200 nm) were dispersed uniformly on the surface of activated carbon and graphene. Electrochemical data indicate that the composite exhibited good electrochemical performances. The PbO/GN/AC composite possessed the higher over-potential of hydrogen evolution and the high specific capacitance of 312.6 F·g^-1, while the internal resistance …

Boosting Electrocatalytic Activity Of Nitrogen-Doped Graphene/Carbon Nanotube Composite For Oxygen Reduction Reaction, Yu Zhang, Jin-Song Hu, Wen-Jie Jiang, Lin Guo, Zi-Dong Wei, Li-Jun Wan

Journal of Electrochemistry

Developing low-cost catalysts with high electrocatalytic activity for oxygen reduction reaction (ORR) has recently attracted much attention because the sluggish ORR currently limits the performance and commercialization of fuel cells and metal-air batteries as well. Nitrogen doped carbon materials have been considered as a promising candidate for the replacement of high-cost and scarce Pt-based catalysts although their electrocatalytic activity still needs to be much improved. In this work, an improved nitrogen-doped graphene/carbon nanotubes composite (N-rGO/CNT) was developed as an efficient ORR electrocatalyst. It was found that the ORR activity of N-rGO/CNT composite could be significantly enhanced by introducing iron in …

High-Performance Sodium-Ion Batteries And Sodium-Ion Pseudocapacitors Based On Mos2/Graphene Composites, Yunxiao Wang, Shulei Chou, David Wexler, Hua-Kun Liu, S X. Dou

Shi Xue Dou

Sodium-ion energy storage, including sodium-ion batteries (NIBs) and electrochemical capacitive storage (NICs), is considered as a promising alternative to lithium-ion energy storage. It is an intriguing prospect, especially for large-scale applications, owing to its low cost and abundance. MoS2 sodiation/desodiation with Na ions is based on the conversion reaction, which is not only able to deliver higher capacity than the intercalation reaction, but can also be applied in capacitive storage owing to its typically sloping charge/discharge curves. Here, NIBs and NICs based on a graphene composite (MoS2/G) were constructed. The enlarged d-spacing, a contribution of the graphene matrix, and the …

Transport And Optical Properties Of Low-Dimensional Complex Systems, Andrii Iurov

Dissertations, Theses, and Capstone Projects

Over the last five years of my research work, I, my research was mainly concerned with certain crucial tunneling, transport and optical properties of novel low-dimensional graphitic and carbon-based materials as well as topological insulators. Both single-electron and many-body problems were addressed. We investigated the Dirac electrons transmission through a potential barrier in the presence of circularly polarized light. An anomalous photon-assisted enhanced transmission is predicted and explained in a comparison with the well-known Klein paradox. It is demonstrated that the perfect transmission for nearly-head-on collision in an infinite graphene is suppressed in gapped dressed states of electrons, which is …

Preparation Of Pt-Tio2/Graphene Composites With High Catalytic Activity Towards Methanol Oxidation And Oxygen Reduction Reaction, Li Qi, Ying Yin, Wen-Guang Tu, Bing-Bing Wu, Zhao-Sheng Wang, Jian-Guo Liu, Jun Gu, Zhi-Gang Zou

Journal of Electrochemistry

A series of graphene-supported TiO₂ nanoparticles (TiO₂/G) with different TiO₂ contents were prepared by a facile hydrothermal method, and then the Pt-TiO₂/G catalysts were successfully prepared by reducing Pt-precursor with microwave technique. Compared with Pt-G catalysts, the catalytic performance toward oxygen reduction reaction (ORR) and methanol oxidation reaction (MOR) of Pt-TiO₂/G catalysts was improved due to the addition of TiO₂. However, the excessive TiO₂ would lead to a poor catalytic performance of Pt-TiO₂/G catalysts because of the low electrical conductivity of TiO₂.

Theoretical Studies Of The Growth And Functionality Of Layered Materials, Wei Chen

Doctoral Dissertations

In this thesis, we present several projects on the growth and functionality of layered materials, using density functional theory (DFT) method and phenomenological modeling approach. Beyond the understanding of growth mechanisms and exploration of properties, we propose novel avenues to realize controllable growth processes and layered materials with desirable properties. The contents have three major parts:

(1) Graphene growth on Cu(111) and Ni(111) substrates. We first demonstrate that the inherent multi-orientational degeneracy of the graphene islands on Cu(111) in the early stages of nucleation could result in the prevalence of grain boundaries (GBs). Next, we propose a possible solution to …

Nanoscale Manipulation Of Pristine And Functionalized Freestanding Graphene Using Scanning Tunneling Microscopy, Matthew Ackerman

Graduate Theses and Dissertations

Over the past ten years the 2D material graphene has attracted an enourmous amount of attention from researchers from across diciplines and all over the world. Many of its outstanding electronic properties are present only when it is not interacting with a substrate but is instead freestanding. In this work I demonstrate that pristine and functionalized freestanding graphene can be imaged using a scanning tunneling microscope (STM) and that imaging a flexible 2D surface is fundamentally different from imaging a bulk material due to the attraction between the STM tip and the sample. This attraction can be used to manipulate …

Binding Of Solvated Peptide (Eplqlkm) With A Graphene Sheet Via Simulated Coarse-Grained Approach, Somayyeh Sheikholeslami, R. B. Pandey, Nadiya Dragneva, Wely Floriano, Oleg Rubel, Stephen A. Barr, Zhifeng Kuang, Rajiv Berry, Rajesh Naik, Barry Farmer

Faculty Publications

Binding of a solvated peptide A1 (¹E ²P ³L ⁴Q ⁵L ⁶K ⁷M) with a graphene sheet is studied by a coarse-grained computer simulation involving input from three independent simulated interaction potentials in hierarchy. A number of local and global physical quantities such as energy, mobility, and binding profiles and radius of gyration of peptides are examined as a function of temperature (T). Quantitative differences (e.g., the extent of binding within a temperature range) and qualitative similarities are observed in results from three simulated potentials. Differences in variations of both local and …

Quantitative Analysis Of Structure And Bandgap Changes In Graphene Oxide Nanoribbons During Thermal Annealing, Yu Zhu, Xianyu Li, Qinjia Cai, Zhengzong Sun, Gilberto Casillas, Miguel Jose-Yacaman, Rafael Verduzco, James Tour

Yu Zhu

Graphene oxide nanoribbons (GONRs) are wide bandgap semiconductors that can be reduced to metallic graphene nanoribbons. The transformation of GONRs from their semiconductive to the metallic state by annealing has attracted significant interest due to its simplicity. However, the detailed process by which GONRs transform from widebandgap semiconductors to semimetals with a near zero bandgap is unclear. As a result, precise control of the bandgap between these two states is not currently achievable. Here, we quantitatively examine the removal of oxygen-containing groups and changes in the bandgap during thermal annealing of GONRs. X-ray photoelectron spectroscopy measurements show the progressive removal …

A Seemless Three-Dimensional Carbon Nanotube Graphene Hybrid Material, Yu Zhu, Lei Li, Gilberto Casillas, Zhengzong Sun, Zheng Yan, Gedeng Ruan, Zhiwei Peng, Abdul-Rahman Raji, Carter Kittrell, Robert Hauge, James Tour

Yu Zhu

Graphene and single-walled carbon nanotubes are carbon materials that exhibit excellent electrical conductivities and large specific surface areas. Theoretical work suggested that a covalently bonded graphene/single-walled carbon nanotube hybrid material would extend those properties to three dimensions, and be useful in energy storage and nanoelectronic technologies. Here we disclose a method to bond graphene and single-walled carbon nanotubes seamlessly during the growth stage. The hybrid material exhibits a surface area 42,000m2 g1 with ohmic contact from the vertically aligned single-walled carbon nanotubes to the graphene. Using aberration-corrected scanning transmission electron microscopy, we observed the covalent transformation of sp2 carbon between …

Optimization Of Chemical Vapor Deposition Grown Graphene, Andrew Tan

Senior Theses

Graphene can be used as the active film in a gas sensor. To provide the best possible electrical properties, it is important that graphene films be single-layered and single-crystalline. A low vacuum chemical vapor deposition (CVD) chamber was constructed to grow graphene with these properties. The effect of growth parameters, such as annealing times and methane partial pressure, on the quality of graphene was investigated. Raman spectra of graphene were used to quantify the characteristics of the synthesized graphene. Graphene synthesized through CVD has two major peaks, the G (~1570cm^-1) and the 2D peak (~2700 cm^-1). …

Discrete Strain Engineering In Graphene, Cedric Marcus Horvath

Graduate Theses and Dissertations

Graphene has a number of fascinating mechanical and electrical properties. Strain engineering in graphene is the attempt to control its properties with mechanical strain. Previous research in this area has come up with an approach using a continuum theory to describe the strain induced gauge fields in graphene; however, this approach is only valid for small strains (5% at most). A discrete framework is being developed in Arkansas that can more accurately calculate the deformation (electrical) and (pseudo-)magnetic gauge fields created by large strains. Computational simulations were carried out and used to get discrete atomic positions for strained, suspended graphene …

Atomic-Scale Characterization And Manipulation Of Freestanding Graphene Using Adapted Capabilities Of A Scanning Tunneling Microscope, Steven Barber

Graduate Theses and Dissertations

Graphene was the first two-dimensional material ever discovered, and it exhibits many unusual phenomena important to both pure and applied physics. To ensure the purest electronic structure, or to study graphene's elastic properties, it is often suspended over holes or trenches in a substrate. The aim of the research presented in this dissertation was to develop methods for characterizing and manipulating freestanding graphene on the atomic scale using a scanning tunneling microscope (STM). Conventional microscopy and spectroscopy techniques must be carefully reconsidered to account for movement of the extremely flexible sample.

First, the acquisition of atomic-scale images of freestanding graphene …

Fabrication And Electrochemical Properties Of Graphene-Zno Nanocomposite, Chuan-Ling Men, Wan Wang, Jun Cao

Journal of Electrochemistry

In this work, the graphene-ZnO nanocomposite was successfully synthesized through a one-step solvothermal approach, using ethylene glycol as the solvent and reducing agent. The ZnO particles could be attached to the surfaces and edges of graphene sheet. The electrochemical performance of the nanocomposite was investigated by performing cyclic voltammetry, A.C. impedance and chronopotentiometry tests in 6 mol·L^-1 KOH. The results showed that the graphene-ZnO nanocomposite exhibited a nice electrochemical specific capacitance of 115 F·g^-1 determined in cyclic voltammetry test, or 71 F·g^-1 evaluated in chronopotentiometry test and good reversible charge/discharge behavior.

Aqueous Dispersions Of Reduced Graphene Oxide And Multi Wall Carbon Nanotubes For Enhanced Glucose Oxidase Bioelectrode Performance, Willo Grosse, Joffrey Champavert, Sanjeev Gambhir, Gordon G. Wallace, Simon E. Moulton

Gordon Wallace

Aqueous dispersions of reduced graphene oxide (rGO) and multi walled carbon nanotubes (MWCNT) were fabricated through a modified chemical reduction method. The significant advantage of the method developed here is the omission of any stabilising compound or organic solvent to obtain stable rGO-MWCNT dispersions. Significantly biological entities, in this case the enzyme glucose oxidase (GOx), can be successfully incorporated into the dispersion. These dispersions were characterised using XPS, SEM, zeta potential and particle size measurements which showed that the dispersion stability is not sacrificed with the addition of GOx, and significantly, the electrical properties of the rGO and MWCNTs are …

Fabrication Of Graphene Electrodes By Electrophoretic Deposition And Their Synergistic Effects With Pedot And Platinum, Widsanusan Chartarrayawadee, Simon E. Moulton, Chee O. Too, Gordon G. Wallace

Gordon Wallace

This research presents a useful electrophoretic deposition (EPD) technique for electrode fabrication from an aqueous colloidal solution of graphene to produce graphene electrodes by the deposition of graphene on to indium-tin oxide (ITO) coated glass. Resultant graphene electrodes are composited with conducting polymer (PEDOT), and platinum nanoparticles, to investigate their synergistic effects. Firstly, PEDOT is composited with graphene by electropolymerization on to the graphene layer. The graphene/PEDOT electrodes demonstrate an improvement in electrochemical response in tetrabutylammonium perchlorate/ acetonitrile solution. Secondly, graphene electrodes are composited with platinum by EPD of platinum nanoparticles on to the graphene layer. The resultant graphene/platinum electrodes …

Facile Synthesis Of Reduced Graphene Oxide/Mwnts Nanocomposite Supercapacitor Materials Tested As Electrophoretically Deposited Films On Glassy Carbon Electrodes, Widsanusan Chartarrayawadee, Simon E. Moulton, Chee O. Too, Byung C. Kim, Rao Yepuri, Anthony C. Romeo, Gordon G. Wallace

Gordon Wallace

This paper reports on a facile synthesis method for reduced graphene oxide (rGO)/multi-walled carbon nanotubes (MWNTs) nanocomposites. The initial step involves the use of graphene oxide to disperse the MWNTs, with subsequent reduction of the resultant graphene oxide/MWNTs composites using l-ascorbic acid (LAA) as a mild reductant. Reduction by LAA preserves the interaction between the rGO sheets and MWNTs. The dispersion-containing rGO/MWNTs composites was characterized and electrophoretically deposited anodically onto glassy carbon electrodes to form high surface area films for capacitance testing. Pseudo capacitance peaks were observed in the rGO/MWNTs composite electrodes, resulting in superior performance with capacitance values up …

Scalable One-Step Wet-Spinning Of Graphene Fibers And Yarns From Liquid Crystalline Dispersions Of Graphene Oxide: Towards Multifunctional Textiles, Rouhollah Jalili, Seyed Hamed Aboutalebi, Dorna Esrafilzadeh, Roderick L. Shepherd, Jun Chen, Sima Aminorroaya-Yamini, Konstantin Konstantinov, Andrew I. Minett, Joselito M. Razal, Gordon G. Wallace

Gordon Wallace

Key points in the formation of liquid crystalline (LC) dispersions of graphene oxide (GO) and their processability via wet-spinning to produce long lengths of micrometer-dimensional fibers and yarns are addressed. Based on rheological and polarized optical microscopy investigations, a rational relation between GO sheet size and polydispersity, concentration, liquid crystallinity, and spinnability is proposed, leading to an understanding of lyotropic LC behavior and fiber spinnability. The knowledge gained from the straightforward formulation of LC GO "inks" in a range of processable concentrations enables the spinning of continuous conducting, strong, and robust fibers at concentrations as low as 0.075 wt%, eliminating …

Carbon Nanotube-Reduced Graphene Oxide Composites For Thermal Energy Harvesting Applications, Mark S. Romano, Na Li, Dennis Antiohos, Joselito M. Razal, Andrew Nattestad, Stephen Beirne, Shaoli Fang, Yongsheng Chen, Rouhollah Jalili, Gordon G. Wallace, Ray Baughman, Jun Chen

Gordon Wallace

By controlling the SWNT-rGO electrode composition and thickness to attain the appropriate porosity and tortuosity, the electroactive surface area is maximized while rapid diffusion of the electrolyte through the electrode is maintained. This leads to an increase in exchange current density between the electrode and electrolyte which results in enhanced thermocell performance.

Organic Solvent-Based Graphene Oxide Liquid Crystals: A Facile Route Toward The Next Generation Of Self-Assembled Layer-By-Layer Multifunctional 3d Architectures, Rouhollah Jalili, Seyed Hamed Aboutalebi, Dorna Esrafilzadeh, Konstantin Konstantinov, Simon E. Moulton, Joselito M. Razal, Gordon G. Wallace

Gordon Wallace

We introduce soft self-assembly of ultralarge liquid crystalline (LC) graphene oxide (GO) sheets in a wide range of organic solvents overcoming the practical limitations imposed on LC GO processing in water. This expands the number of known solvents which can support amphiphilic self-assembly to ethanol, acetone, tetrahydrofuran, N-dimethylformamide, N-cyclohexyl-2-pyrrolidone, and a number of other organic solvents, many of which were not known to afford solvophobic self-assembly prior to this report. The LC behavior of the as-prepared GO sheets in organic solvents has enabled us to disperse and organize substantial amounts of aggregate-free single-walled carbon nanotubes (SWNTs, up to 10 wt …

Manganosite-Microwave Exfoliated Graphene Oxide Composites For Asymmetric Supercapacitor Device Applications, Dennis Antiohos, Kanlaya Pingmuang, Mark Romano, Stephen Beirne, Tony C. Romeo, Phil Aitchison, Andrew I. Minett, Gordon G. Wallace, Sukon Phanichphant, Jun Chen

Gordon Wallace

Graphene based materials coupled with transition metal oxides are promising electrode materials in asymmetric supercapacitors owing to their unique properties which include high surface area, good chemical stability, electrical conductivity, abundance, and lower cost profile over time. In this paper a composite material consisting of graphene oxide exfoliated with microwave radiation (mw rGO), and manganosite (MnO) is synthesised in order to explore their potential as an electrode material. The composite material was characterised by scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and Raman spectroscopy. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) were used to explore …

Covalently Linked Biocompatible Graphene/Polycaprolactone Composites For Tissue Engineering, Sepidar Sayyar, Eoin Murray, Brianna C. Thompson, Sanjeev Gambhir, David L. Officer, Gordon G. Wallace

Gordon Wallace

Two synthesis routes to graphene/polycaprolactone composites are introduced and the properties of the resulting composites compared. In the first method, mixtures are produced using solution processing of polycaprolactone and well dispersed, chemically reduced graphene oxide and in the second, an esterification reaction covalently links polycaprolactone chains to free carboxyl groups on the graphene sheets. This is achieved through the use of a stable anhydrous dimethylformamide dispersion of graphene that has been highly chemically reduced resulting in mostly peripheral ester linkages. The resulting covalently linked composites exhibit far better homogeneity and as a result, both Young's modulus and tensile strength more …

Reduced Graphene Oxide With Superior Cycling Stability And Rate Capability For Sodium Storage, Yunxiao Wang, Shulei Chou, Hua-Kun Liu, S X. Dou

Shi Xue Dou

Sodium ion battery is a promising electrical energy storage system for sustainable energy storage applications due to the abundance of sodium resources and their low cost. In this communication, the electrochemical properties of sodium ion storage in reduced graphene oxide (RGO) were studied in an electrolyte consisting of 1 M NaClO4 in propylene carbonate (PC). The experimental results show that the RGO anode allowed significant sodium ion insertion, leading to higher capacity at high current density compared to the previously reported results for carbon materials. This is due to the fact that RGO possesses higher electrical conductivity and is a …

A Facile Route To Synthesize Transition Metal Oxide/Reduced Graphene Oxide Composites And Their Lithium Storage Performance, Chongjun Zhao, Shulei Chou, Yunxiao Wang, Cuifeng Zhou, Hua-Kun Liu, S X. Dou

Shi Xue Dou

Transition metal oxide (Mn3O4, Fe2O3, Co3O4, and ZnO) and reduced graphene oxide (RGO) composites were successfully synthesized via a hydrothermal method using the direct reaction between the corresponding metal powder and graphene oxide (GO). In this process, the GO can be reduced by transition metal powder in water, and the nanosized metal oxide can be obtained, and homogeneously mixed with and wrapped by RGO to form a metal oxide/RGO composite at the same time. X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy, and scanning and transmission electron microscopy were used to characterize the as-prepared materials. The different experimental parameters, including reactants, …

Fusion Of Nacre, Mussel, And Lotus Leaf: Bio-Inspired Graphene Composite Paper With Multifunctional Integration, Da Zhong, Qinglin Yang, Lin Guo, S X. Dou, Kesong Liu, Lei Jiang

Shi Xue Dou

Multifunctional integration is an inherent characteristic for biological materials with multiscale structures. Learning from nature is an effective approach for scientists and engineers to construct multifunctional materials. In nature, mollusks (abalone), mussels, and the lotus have evolved different and optimized solutions to survive. Here, bio-inspired multifunctional graphene composite paper was fabricated in situ through the fusion of the different biological solutions from nacre (brick-and-mortar structure), mussel adhesive protein (adhesive property and reducing character), and the lotus leaf (self-cleaning effect). Owing to the special properties (self-polymerization, reduction, and adhesion), dopamine could be simultaneously used as a reducing agent for graphene oxide …

The Electrochemical Properties Of High-Capacity Sulfur/Reduced Graphene Oxide With Different Electrolyte Systems, Yunxiao Wang, Shulei Chou, Hua-Kun Liu, S X. Dou

Shi Xue Dou

The lithium/sulfur battery is a promising electrochemical system with high capacity, which is well-known to undergo a complex multistep reaction during the discharge process. Two types of electrolytes including poly (ethylene glycol) dimethyl ether (PEGDME)-based and 1.3 - dioxolane (DOL)/ dimethoxyethane (DME)-based electrolytes were investigated here. Furthermore, LiNO3 additive was introduced into the electrolyte in order to effectively eliminate the overcharge effect. The lithium sulfur battery with 1.0 M LiN(CF3SO2)2 in PEGME with 0.1 M LiNo3 shows highly stable reversible capacity of 624.8 mAh g-1 after 200 cycles and improved average coulombic efficiency of 98 percent.