Open Access. Powered by Scholars. Published by Universities.®
Physical Sciences and Mathematics Commons™
Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 14 of 14
Full-Text Articles in Physical Sciences and Mathematics
Mesoporous Hexagonal Co3o4 For High Performance Lithium Ion Batteries, Dawei Su, Xiuqiang Xie, Paul Munroe, S X. Dou, Guoxiu Wang
Mesoporous Hexagonal Co3o4 For High Performance Lithium Ion Batteries, Dawei Su, Xiuqiang Xie, Paul Munroe, S X. Dou, Guoxiu Wang
Australian Institute for Innovative Materials - Papers
Mesoporous Co3O4 nanoplates were successfully prepared by the conversion of hexagonal beta-Co(OH)(2) nanoplates. TEM, HRTEM and N-2 sorption analysis confirmed the facet crystal structure and inner mesoporous architecture. When applied as anode materials for lithium storage in lithium ion batteries, mesoporous Co3O4 nanocrystals delivered a high specific capacity. At 10 degrees C current rate, as-prepared mesoporous Co3O4 nanoplates delivered a specific capacity of 1203 mAh/g at first cycle and after 200 cycles it can still maintain a satisfied value (330 mAh/g). Fromex-situ TEM, SAED and FESEM observation, it was found that mesoporous Co3O4 nanoplates were reduced to Li2O and Co …
Study On Vanadium Substitution To Iron In Li2fep 2o7 As Cathode Material For Lithium-Ion Batteries, Jiantie Xu, Shulei Chou, Qinfen Gu, M F. Md Din, Hua-Kun Liu, S X. Dou
Study On Vanadium Substitution To Iron In Li2fep 2o7 As Cathode Material For Lithium-Ion Batteries, Jiantie Xu, Shulei Chou, Qinfen Gu, M F. Md Din, Hua-Kun Liu, S X. Dou
Australian Institute for Innovative Materials - Papers
A series of Li2Fe1-3x/2VxP 2O7 (x = 0, 0.025, 0.05, 0.075, and 0.1) cathode materials for LIBs were prepared by the sol-gel method. Structural characterization of Li2Fe1-3x/2VxP2O7 (x = 0, 0.025, 0.05, 0.075, and 0.1) samples was conducted by synchrotron X-ray diffraction. The morphology and oxidation states of Fe2+ and V 3+ in the Li2Fe1-3x/2VxP 2O7 samples were confirmed by scanning electron microscopy and magnetic susceptibility measurements, respectively. The electrochemical measurements indicated that Li2Fe1-3x/2VxP 2O7 (x = 0.025) delivered the higher reversible capacity of 79.9 mAh g-1 at 1 C in the voltage range of 2.0 - 4.5 V with …
Na3v2(Po4)3 Particles Partly Embedded In Carbon Nanofibers With Superb Kinetics For Ultra-High Power Sodium Ion Batteries, Junghoon Yang, Dongwook Han, Mi Ru Jo, Kyeongse Song, Yongil Kim, Shulei Chou, Hua-Kun Liu, Yong-Mook Kang
Na3v2(Po4)3 Particles Partly Embedded In Carbon Nanofibers With Superb Kinetics For Ultra-High Power Sodium Ion Batteries, Junghoon Yang, Dongwook Han, Mi Ru Jo, Kyeongse Song, Yongil Kim, Shulei Chou, Hua-Kun Liu, Yong-Mook Kang
Australian Institute for Innovative Materials - Papers
We here describe the extraordinary performance of NASICON Na3V2(PO4)3-carbon nanofiber (NVP-CNF) composites with ultra-high power and excellent cycling performance. NVP-CNFs are composed of CNFs at the center part and partly embedded NVP nanoparticles in the shell. We first report this unique morphology of NVP-CNFs for the electrode material of secondary batteries as well as for general energy conversion materials. Our NVP-CNFs show not only a high discharge capacity of approx. 88.9 mA h g-1 even at a high current density of 50 C but also approx. 93% cyclic retention property after …
Novel Germanium/Polypyrrole Composite For High Power Lithium-Ion Batteries, Xuanwen Gao, Wenbin Luo, Chao Zhong, David Wexler, Shulei Chou, Hua-Kun Liu, Zhicong Shi, Guohua Chen, Kiyoshi Ozawa, Jiazhao Wang
Novel Germanium/Polypyrrole Composite For High Power Lithium-Ion Batteries, Xuanwen Gao, Wenbin Luo, Chao Zhong, David Wexler, Shulei Chou, Hua-Kun Liu, Zhicong Shi, Guohua Chen, Kiyoshi Ozawa, Jiazhao Wang
Australian Institute for Innovative Materials - Papers
Nano-Germanium/polypyrrole composite has been synthesized by chemical reduction method in aqueous solution. The Ge nanoparticles were directly coated on the surface of the polypyrrole. The morphology and structural properties of samples were determined by X-ray diffraction, scanning electron microscopy and transmission electron microscopy. Thermogravimetric analysis was carried out to determine the polypyrrole content. The electrochemical properties of the samples have been investigated and their suitability as anode materials for the lithium-ion battery was examined. The discharge capacity of the Ge nanoparticles calculated in the Ge-polypyrrole composite is 1014 mAh g-1 after 50 cycles at 0.2 C rate, which is …
Α-Fe2o3/Graphene Nanocomposite As Anode Material For Sodium-Ion Batteries With Enhanced Capacity Retention, Zhijia Zhang, Yunxiao Wang, Shulei Chou, Huijun Li, Hua-Kun Liu, Jiazhao Wang
Α-Fe2o3/Graphene Nanocomposite As Anode Material For Sodium-Ion Batteries With Enhanced Capacity Retention, Zhijia Zhang, Yunxiao Wang, Shulei Chou, Huijun Li, Hua-Kun Liu, Jiazhao Wang
Australian Institute for Innovative Materials - Papers
Among the different energy storage systems, rechargeable lithium-ion batteries (LIBs) have been widely applied in various portable electronic devices due to their high energy densities, long cycle life, and lack of significant memory effect [1]. For wide-scale implementation of renewable energy, LIBs, however, face challenges related to their safety, lifetime, and cost. Based on the wide availability and low cost of sodium, sodium-ion batteries (SIBs) have the potential for meeting the demands of large-scale and sustainable applications. Many cathode materials have been proposed, whereas only a few anode materials have been investigated for SIBs [2]. The sodium ion (1.02 Å) …
Microemulsion-Assisted Synthesis Of Nanosized Li-Mn-O Spinel Cathodes For High-Rate Lithium-Ion Batteries, Xianhong Rui, Wenping Sun, Qingyu Yan, Tuti M. Lim, Maria Skyllas-Kazacos
Microemulsion-Assisted Synthesis Of Nanosized Li-Mn-O Spinel Cathodes For High-Rate Lithium-Ion Batteries, Xianhong Rui, Wenping Sun, Qingyu Yan, Tuti M. Lim, Maria Skyllas-Kazacos
Australian Institute for Innovative Materials - Papers
Li1.16Mn1.84O4 nanoparticles (50-90 nm) with cubic spinel structure are synthesized by combining a microemulsion process to produce ultrafine Mn(OH)2 nanocrystals (3-8 nm) with a solid-state lithiation step. The nanostructured lithium-rich Li1.16Mn1.84O4 shows stable cycling performance and superior rate capabilities as compared with the corresponding bulk material, for example, the nano-sized Li1.16Mn1.84O4 electrode shows stable reversible capacities of 74 mAhg-1 during the 1000th cycle at a high rate of 40 C between 3.0 and 4.5 V. In addition, Li1.16Mn1.84O4 nanoparticles also show high Li storage properties over an enlarged voltage window of 2.0-4.5 V with high capacities and stable cyclability, for …
Three-Dimensional-Network Li3v2(Po4) 3/C Composite As High Rate Lithium Ion Battery Cathode Material And Its Compatibility With Ionic Liquid Electrolytes, Jiantie Xu, Shulei Chou, Cuifeng Zhou, Qinfen Gu, Hua-Kun Liu, S X. Dou
Three-Dimensional-Network Li3v2(Po4) 3/C Composite As High Rate Lithium Ion Battery Cathode Material And Its Compatibility With Ionic Liquid Electrolytes, Jiantie Xu, Shulei Chou, Cuifeng Zhou, Qinfen Gu, Hua-Kun Liu, S X. Dou
Australian Institute for Innovative Materials - Papers
A high performance Li3V2(PO4)3 cathode material for lithium ion batteries was synthesized by the microwave-assisted hydrothermal method followed by a post annealing process. The synchrotron X-ray diffraction analysis results confirmed that single-phase Li3V2(PO4)3 with monoclinic structure was obtained. Scanning electron microscope and transmission electron microscope images revealed that the as-prepared Li3V 2(PO4)3 was composed of nanowires and microsized particles. Electrochemical results demonstrated that the Li 3V2(PO4)3 electrode measured at 10 C after 500 cycles can deliver discharge capacities of 85.4 mAh g-1 and 103.4 mAh g-1, with a capacity retention of 99.3% and 95.9%, in the voltage ranges of 3.0-4.3 …
Microwave Autoclave Synthesized Multi-Layer Graphene/Single-Walled Carbon Nanotube Composites For Free-Standing Lithium-Ion Battery Anodes, Chao Zhong, Jia-Zhao Wang, David Wexler, Hua-Kun Liu
Microwave Autoclave Synthesized Multi-Layer Graphene/Single-Walled Carbon Nanotube Composites For Free-Standing Lithium-Ion Battery Anodes, Chao Zhong, Jia-Zhao Wang, David Wexler, Hua-Kun Liu
Australian Institute for Innovative Materials - Papers
Multi-layer graphene sheets have been synthesized by a time-efficient microwave autoclave method and used to form composites in situ with single-walled carbon nanotubes. The application of these composites as flexible free-standing film electrodes was then investigated. According to the transmission electron microscopy and X-ray diffraction characterizations, the average d-spacing of the graphene-single-walled carbon nanotube composites was 0.41 nm, which was obviously larger than that of the as-prepared pure graphene (0.36 nm). The reversible Li-cycling properties of the free-standing films have been evaluated by galvanostatic discharge-charge cycling and electrochemical impedance spectroscopy. Results showed that the free-standing composite film with 70 wt% …
A Germanium/Single-Walled Carbon Nanotube Composite Paper As A Free-Standing Anode For Lithium-Ion Batteries, Jun Wang, Jiazhao Wang, Ziqi Sun, Xuanwen Gao, Chao Zhong, Shulei Chou, Hua-Kun Liu
A Germanium/Single-Walled Carbon Nanotube Composite Paper As A Free-Standing Anode For Lithium-Ion Batteries, Jun Wang, Jiazhao Wang, Ziqi Sun, Xuanwen Gao, Chao Zhong, Shulei Chou, Hua-Kun Liu
Australian Institute for Innovative Materials - Papers
Paper-like free-standing germanium (Ge) and single-walled carbon nanotube (SWCNT) composite anodes were synthesized by the vacuum filtration of Ge/SWCNT composites, which were prepared by a facile aqueous-based method. The samples were characterized by X-ray diffraction, field emission scanning electron microscopy, and transmission electron microscopy. Electrochemical measurements demonstrate that the Ge/SWCNT composite paper anode with the weight percentage of 32% Ge delivered a specific discharge capacity of 417 mA h g−1 after 40 cycles at a current density of 25 mA g−1, 117% higher than the pure SWCNT paper anode. The SWCNTs not only function as a flexible mechanical support for …
High-Performance Sodium-Ion Batteries And Sodium-Ion Pseudocapacitors Based On Mos2/Graphene Composites, Yunxiao Wang, Shulei Chou, David Wexler, Hua-Kun Liu, S X. Dou
High-Performance Sodium-Ion Batteries And Sodium-Ion Pseudocapacitors Based On Mos2/Graphene Composites, Yunxiao Wang, Shulei Chou, David Wexler, Hua-Kun Liu, S X. Dou
Australian Institute for Innovative Materials - Papers
Sodium-ion energy storage, including sodium-ion batteries (NIBs) and electrochemical capacitive storage (NICs), is considered as a promising alternative to lithium-ion energy storage. It is an intriguing prospect, especially for large-scale applications, owing to its low cost and abundance. MoS2 sodiation/desodiation with Na ions is based on the conversion reaction, which is not only able to deliver higher capacity than the intercalation reaction, but can also be applied in capacitive storage owing to its typically sloping charge/discharge curves. Here, NIBs and NICs based on a graphene composite (MoS2/G) were constructed. The enlarged d-spacing, a contribution of the graphene matrix, and the …
Enhanced Sodium-Ion Battery Performance By Structural Phase Transition From Two-Dimensional Hexagonal-Sns2 To Orthorhombic-Sns, Tengfei Zhou, Wei Kong Pang, Chaofeng Zhang, Jianping Yang, Zhixin Chen, Hua-Kun Liu, Zaiping Guo
Enhanced Sodium-Ion Battery Performance By Structural Phase Transition From Two-Dimensional Hexagonal-Sns2 To Orthorhombic-Sns, Tengfei Zhou, Wei Kong Pang, Chaofeng Zhang, Jianping Yang, Zhixin Chen, Hua-Kun Liu, Zaiping Guo
Australian Institute for Innovative Materials - Papers
Structural phase transitions can be used to alter the properties of a material without adding any additional elements and are therefore of significant technological value. It was found that the hexagonal-SnS2 phase can be transformed into the orthorhombic-SnS phase after an annealing step in an argon atmosphere, and the thus transformed SnS shows enhanced sodium-ion storage performance over that of the SnS2, which is attributed to its structural advantages. Here, we provide the first report on a SnS@graphene architecture for application as a sodium-ion battery anode, which is built from two-dimensional SnS and graphene nanosheets as complementary building blocks. The …
Cuo Single Crystal With Exposed {001} Facets-A Highly Efficient Material For Gas Sensing And Li-Ion Battery Applications, Dawei Su, Xiuqiang Xie, S X. Dou, Guoxiu Wang
Cuo Single Crystal With Exposed {001} Facets-A Highly Efficient Material For Gas Sensing And Li-Ion Battery Applications, Dawei Su, Xiuqiang Xie, S X. Dou, Guoxiu Wang
Australian Institute for Innovative Materials - Papers
Single crystal copper oxide nanoplatelets with a high percentage of {001} facets were synthesized by a facile hydrothermal approach. The as-prepared materials were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, field emission scanning electron microscopy, and high resolution transmission microscopy. Via density functional theory calculations, it was found that the {001} facets are active crystal planes. When the single crystal CuO nanoplatelets were applied as an anode material in Li-ion batteries, they demonstrated outstanding electrochemical performance with high lithium storage capacity, satisfactory cyclability, and excellent high rate capacity. When used as a sensing material in gas sensors, they exhibited …
Synthesis And Electrochemical Properties Of Wo3/C For Lithium Ion Batteries, Hong Gao, Shuijin S. Yang, Chuanqi Feng, Jiazhao Wang, Zaiping Guo
Synthesis And Electrochemical Properties Of Wo3/C For Lithium Ion Batteries, Hong Gao, Shuijin S. Yang, Chuanqi Feng, Jiazhao Wang, Zaiping Guo
Australian Institute for Innovative Materials - Papers
WO3/C nanorods were prepared by a combination of hydrothermal synthesis method and the solid phase reaction method, using (NH4)10H2(W2O7)6, H2C2O4·2H2O and glucose(carbon source) as raw materials. The effects of different proportions of glucose on the morphologies and electrochemical properties of the final products were systematically investigated. The results showed that the WO3/C nanorods prepared with the 10 wt.% glucose as carbon source exhibited the highest reversible specific capacity (807 mAh g-1) at current density …
Pristine Organo-Imido Polyoxometalates As An Anode For Lithium Ion Batteries, Rao Naumaan Nasim Khan, Nasir Mahmood, Chunlin Lv, Guohui Sima, Jin Zhang, Jian Hao, Yanglong Hou, Yongge Wei
Pristine Organo-Imido Polyoxometalates As An Anode For Lithium Ion Batteries, Rao Naumaan Nasim Khan, Nasir Mahmood, Chunlin Lv, Guohui Sima, Jin Zhang, Jian Hao, Yanglong Hou, Yongge Wei
Australian Institute for Innovative Materials - Papers
Here we have designed a strategy to improve the electronic conductivities of polyoxometalates (POMs) via property-oriented organic grafting for use in lithium-ion batteries (LIBs). POMs usually exhibit limited electronic conductivity that hinders their use in electronic applications. Organic grafting of POMs defines a valuable path for improving electronic conductivities of POMs, due to the enhanced metal to ligand charge transfer (MLCT) via d-π electronic interactions, and results in their feasible application in LIBs. Comparative practical and theoretical study of the effect of functional groups revealed that grafting of the remote electron withdrawing group (-SCN) on POMs via organo-imidoylization along with …