Physical Sciences and Mathematics Commons^™

Obstacles And Solutions To Studying Functional Adhesives Using Vibrational Sum-Frequency Generation Spectroscopy, Angela Renee Andersen

Theses and Dissertations

Important aspects of adhesion occur at interfaces, including structures that may be different from those in the bulk materials. However, probing the orientation of molecules in functional adhesives poses a significant challenge because adhesive molecules are always located at a buried interface. The limited penetration depth of surface-specific analysis prohibits the study of buried interfaces using those techniques. The large quantity of bulk molecules relative to the adhesive molecules interacting at the interface results in the bulk signal swamping out adhesive signal in bulk analysis techniques. An interface-specific technique is required to study functional adhesives. One such technique that has …

Enhancing The Performance Of Organic Thin Film Transistors By Cross-Linking The Organic Gate Dielectric, Soheila Naderi Gohar

Electronic Thesis and Dissertation Repository

Amongst various surface modification techniques, hyperthermal hydrogen induced cross-linking (HHIC) has been used to modify the surface of polymeric samples. In this novel and innovative technique neutral hydrogen projectiles with appropriate kinetic energy are produced to generate carbon radicals on the impacted surface through the collision-induced C-H bond breaking. Subsequently, this phenomenon results in cross-linking hydrocarbon chains in the treated polymeric samples.

Verifying the validity of cross-linking process through experiments is the target of first part of presented dissertation. Spin-coated poly(methyl methacrylate) (PMMA) films on silicon wafer were exposed to hydrogen projectiles for different durations, while the other conditions related …

Measurements Of The Temperature Dependence Of Radiation Induced Conductivity In Polymeric Dielectrics, Jodie Corbridge Gillespie

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Radiation Induced Conductivity (RIC) is the change in conductivity of a material due to bombardment from incident high energy radiation. This study is to determine the effect of RIC and RIC's temperature dependence in polymeric dielectrics, specifically Kapton HN, Kapton E, PTFE Teflon, Tefzel, and Low Density Polyethylene (LDPE). Interest in these materials arises from applications for use in future spacecraft, specifically the James Webb Space Telescope (JWST).

One major issue in the design of JWST, as in all spacecraft, is the charging and arcing of exposed materials, resulting in fatal damage to the electronics and/or the craft itself. Particles …

Synthesis And Characterization Of Biodegradable Poly(Vinyl Esters) With Hdac Inhibitory Activity, Kyle Lawrence Horton

Wayne State University Theses

HDAC inhibitors are known to have anti-inflammatory properties. HDAC inhibitors are used in combination with Oct4 to generate induced pluripotent stem cells. I hypothesized that polyesters based on simple aliphatic HDAC inhibitors like valproic acid (VPA) and phenylbutyric acid (PBA) can serve as alternatives to existing polyester biomaterials with improved anti-inflammatory properties and as scaffolds for generation of iPSCs when used in combination with layer-by-layer thin films delivering reprogramming transcription factors. Vinyl ester of phenylbutyric acid (VEPA) and vinyl ester of valproic acid (VEVA) were synthesized from their carboxylic acid precursors using an iridium complex catalyst at yields as high …

Design, Synthesis And Characterization Of Chain-End Functionalized Glyco-Polymer For Efficient Proteomic Analysis, Satya Nandana Narla

ETD Archive

No abstract provided.

The Enhancement Of Peroxide-Cured Fluoroelastomer Rubber To Metal Bonding, Richard Hunter Cooke Iii

Browse all Theses and Dissertations

A "combi-cured&" fluoroelastomer (FKM) rubber formulation was designed to yield 100% cohesive rubber failure when cured to cold-rolled steel with derivatives of polymeric silane adhesives. Three different categories of adhesives were tested: Unsaturated Polymeric Silane with Phosphonium Salt (UPSP-D), Unsaturated Polymeric Silane (UPS-L), and Saturated Polymeric Silane (SPS-L). Adhesion Inserts molded using ASTM Method D429 Method C all consistently yielded 100% cohesive rubber failure and showed adhesion strength in the range of 700 to 800 psi after being pulled at 2" per minute until break. After obtaining consistent 100% rubber failure, a design of experiment (DOE) was implemented to determine …