Open Access. Powered by Scholars. Published by Universities.®
Physical Sciences and Mathematics Commons™
Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 7 of 7
Full-Text Articles in Physical Sciences and Mathematics
Contribution Of Radicals And Ions In Catalyzed Growth Of Single-Walled Carbon Nanotubes From Low-Temperature Plasmas, Z Marvi, S Xu, G Foroutan, Kostya Ostrikov
Contribution Of Radicals And Ions In Catalyzed Growth Of Single-Walled Carbon Nanotubes From Low-Temperature Plasmas, Z Marvi, S Xu, G Foroutan, Kostya Ostrikov
Australian Institute for Innovative Materials - Papers
The growth kinetics of single-walled carbon nanotubes (SWCNTs) in a low-temperature, low-pressure reactive plasma is investigated using a multiscale numerical simulation, including the plasma sheath and surface diffusion modules. The plasma-related effects on the characteristics of SWCNT growth are studied. It is found that in the presence of reactive radicals in addition to energetic ions inside the plasma sheath area, the effective carbon flux, and the growth rate of SWCNT increase. It is shown that the concentration of atomic hydrogen and hydrocarbon radicals in the plasma plays an important role in the SWCNT growth. The effect of the effective carbon …
Superior Critical Current Density Obtained In Mg11b2 Low Activation Superconductor By Using Reactive Amorphous 11b And Optimizing Sintering Temperature, Fang Cheng, Yongchang Liu, Zongqing Ma, Huijun Li, Md Shahriar Hossain
Superior Critical Current Density Obtained In Mg11b2 Low Activation Superconductor By Using Reactive Amorphous 11b And Optimizing Sintering Temperature, Fang Cheng, Yongchang Liu, Zongqing Ma, Huijun Li, Md Shahriar Hossain
Australian Institute for Innovative Materials - Papers
The un-doped Mg11B2 and Cu-doped Mg11B2 bulks using 11B as a boron precursor were fabricated by solid-state reaction and sintered at different temperature in present work. By analyzing the sintering process, it was found that 11B original powder is more reactive and can react with Mg severely even at low temperature before Mg melting, which leads to the formation of refined Mg11B2 grains. Consequently, the critical current density of Mg11B2 sample prepared in this work is higher than that of natural MgB2. Furthermore, it was found that proper Cu addition …
Significantly Enhanced Critical Current Density In Nano-Mgb2 Grains Rapidly Formed At Low Temperature With Homogeneous Carbon Doping, Yongchang Liu, Feng Lan, Zongqing Ma, Ning Chen, Huijun Li, Shaon Barua, Dipakkumar Patel, Md S. Hossain, S Acar, Jung Ho Kim, S X. Dou
Significantly Enhanced Critical Current Density In Nano-Mgb2 Grains Rapidly Formed At Low Temperature With Homogeneous Carbon Doping, Yongchang Liu, Feng Lan, Zongqing Ma, Ning Chen, Huijun Li, Shaon Barua, Dipakkumar Patel, Md S. Hossain, S Acar, Jung Ho Kim, S X. Dou
Australian Institute for Innovative Materials - Papers
High performance MgB2 bulks using carbon-coated amorphous boron as a boron precursor were fabricated by Cu-activated sintering at low temperature (600 °C, below the Mg melting point). Dense nano-MgB2 grains with a high level of homogeneous carbon doping were formed in these MgB2 samples. This type of microstructure can provide a stronger flux pinning force, together with depressed volatility and oxidation of Mg owing to the low-temperature Cu-activated sintering, leading to a significant improvement of critical current density (Jc) in the as-prepared samples. In particular, the value of Jc for the carbon-coated (Mg …
Conductive Surfaces With Dynamic Switching In Response To Temperature And Salt, Alissa Hackett, Jenny Malmström, Paul J. Molino, Julien Gautrot, Hongrui Zhang, Michael J. Higgins, Gordon G. Wallace, David E. Williams, Jadranka Travas-Sejdic
Conductive Surfaces With Dynamic Switching In Response To Temperature And Salt, Alissa Hackett, Jenny Malmström, Paul J. Molino, Julien Gautrot, Hongrui Zhang, Michael J. Higgins, Gordon G. Wallace, David E. Williams, Jadranka Travas-Sejdic
Australian Institute for Innovative Materials - Papers
This work demonstrates polymer brushes grafted from conductive polymer films which display dynamic surface switching dependent on salt, temperature and electrode potential. The electroactivity presented by the conductive polymer and the responsiveness of the grafted brushes leads to an interface with multiple control parameters. Here, we demonstrate this concept by grafting of uncharged brushes of poly(ethylene glycol)methyl ether methacrylates from conducting polymer poly(3,4-ethylenedioxythiophene) (PEDOT), and observe a temperature- and salt-induced switch of brush conformation, and their effect on the electrochemistry of the material. The switching conditions can be tailored by copolymerizing monomers with different numbers of ethylene glycol units. In …
Harvesting Temperature Fluctuations As Electrical Energy Using Torsional And Tensile Polymer Muscles, Shi Hyeong Kim, Marcio Dias Lima, Mikhail E. Kozlov, Carter S. Haines, Geoffrey M. Spinks, Shazed Aziz, Changsoon Choi, Hyeon Jun Sim, Xuemin Wang, Hongbing Lu, Dong Qian, John D. W Madden, Ray H. Baughman, Seon Jeong Kim
Harvesting Temperature Fluctuations As Electrical Energy Using Torsional And Tensile Polymer Muscles, Shi Hyeong Kim, Marcio Dias Lima, Mikhail E. Kozlov, Carter S. Haines, Geoffrey M. Spinks, Shazed Aziz, Changsoon Choi, Hyeon Jun Sim, Xuemin Wang, Hongbing Lu, Dong Qian, John D. W Madden, Ray H. Baughman, Seon Jeong Kim
Australian Institute for Innovative Materials - Papers
Diverse means have been deployed for harvesting electrical energy from mechanical actuation produced by low-grade waste heat, but cycle rate, energy-per-cycle, device size and weight, or cost have limited applications. We report the electromagnetic harvesting of thermal energy as electrical energy using thermally powered torsional and tensile artificial muscles made from inexpensive polymer fibers used for fishing line and sewing thread. We show that a coiled 27 μm-diameter nylon muscle fiber can be driven by 16.7 °C air temperature fluctuations to spin a magnetic rotor to a peak torsional rotation speed of 70 000 rpm for over 300 000 heating-cooling …
Harvesting Temperature Fluctuations As Electrical Energy Using Torsional And Tensile Polymer Muscles, Shi Hyeong Kim, Marcio Dias Lima, Mikhail E. Kozlov, Carter S. Haines, Geoffrey M. Spinks, Shazed Aziz, Changsoon Choi, Hyeon Jun Sim, Xuemin Wang, Hongbing Lu, Dong Qian, John D. W Madden, Ray H. Baughman, Seon Jeong Kim
Harvesting Temperature Fluctuations As Electrical Energy Using Torsional And Tensile Polymer Muscles, Shi Hyeong Kim, Marcio Dias Lima, Mikhail E. Kozlov, Carter S. Haines, Geoffrey M. Spinks, Shazed Aziz, Changsoon Choi, Hyeon Jun Sim, Xuemin Wang, Hongbing Lu, Dong Qian, John D. W Madden, Ray H. Baughman, Seon Jeong Kim
Australian Institute for Innovative Materials - Papers
Diverse means have been deployed for harvesting electrical energy from mechanical actuation produced by low-grade waste heat, but cycle rate, energy-per-cycle, device size and weight, or cost have limited applications. We report the electromagnetic harvesting of thermal energy as electrical energy using thermally powered torsional and tensile artificial muscles made from inexpensive polymer fibers used for fishing line and sewing thread. We show that a coiled 27 μm-diameter nylon muscle fiber can be driven by 16.7 °C air temperature fluctuations to spin a magnetic rotor to a peak torsional rotation speed of 70 000 rpm for over 300 000 heating-cooling …
Improvement In Structure And Superconductivity Of Bulk Fese0.5te0.5 Superconductors By Optimizing Sintering Temperature, Ning Chen, Yongchang Liu, Zongqing Ma, Liming Yu, Huijun Li
Improvement In Structure And Superconductivity Of Bulk Fese0.5te0.5 Superconductors By Optimizing Sintering Temperature, Ning Chen, Yongchang Liu, Zongqing Ma, Liming Yu, Huijun Li
Australian Institute for Innovative Materials - Papers
Sintering temperature plays a vital role in the evolution of phase structure and microstructure in polycrystalline FeSe0.5Te0.5 bulks fabricated by the two-step sintering method, and thus significantly influences their superconducting properties. Elevated sintering temperature (600-700°C) at second step facilitates the substitution of Te into the superconducting phase, which leads to the increased lattice distortion and thus contributes to the enhancement of superconductivity (the value of Tc reaches 15.6K). At the same time, the accelerated growth of the superconducting grains and the improved homogeneity motivated by elevated sintering temperature serve as the main reason for the sharp superconducting transition.