Open Access. Powered by Scholars. Published by Universities.®
Physical Sciences and Mathematics Commons™
Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 8 of 8
Full-Text Articles in Physical Sciences and Mathematics
Microwave Autoclave Synthesized Multi-Layer Graphene/Single-Walled Carbon Nanotube Composites For Free-Standing Lithium-Ion Battery Anodes, Chao Zhong, Jia-Zhao Wang, David Wexler, Hua-Kun Liu
Microwave Autoclave Synthesized Multi-Layer Graphene/Single-Walled Carbon Nanotube Composites For Free-Standing Lithium-Ion Battery Anodes, Chao Zhong, Jia-Zhao Wang, David Wexler, Hua-Kun Liu
Australian Institute for Innovative Materials - Papers
Multi-layer graphene sheets have been synthesized by a time-efficient microwave autoclave method and used to form composites in situ with single-walled carbon nanotubes. The application of these composites as flexible free-standing film electrodes was then investigated. According to the transmission electron microscopy and X-ray diffraction characterizations, the average d-spacing of the graphene-single-walled carbon nanotube composites was 0.41 nm, which was obviously larger than that of the as-prepared pure graphene (0.36 nm). The reversible Li-cycling properties of the free-standing films have been evaluated by galvanostatic discharge-charge cycling and electrochemical impedance spectroscopy. Results showed that the free-standing composite film with 70 wt% …
A Germanium/Single-Walled Carbon Nanotube Composite Paper As A Free-Standing Anode For Lithium-Ion Batteries, Jun Wang, Jiazhao Wang, Ziqi Sun, Xuanwen Gao, Chao Zhong, Shulei Chou, Hua-Kun Liu
A Germanium/Single-Walled Carbon Nanotube Composite Paper As A Free-Standing Anode For Lithium-Ion Batteries, Jun Wang, Jiazhao Wang, Ziqi Sun, Xuanwen Gao, Chao Zhong, Shulei Chou, Hua-Kun Liu
Australian Institute for Innovative Materials - Papers
Paper-like free-standing germanium (Ge) and single-walled carbon nanotube (SWCNT) composite anodes were synthesized by the vacuum filtration of Ge/SWCNT composites, which were prepared by a facile aqueous-based method. The samples were characterized by X-ray diffraction, field emission scanning electron microscopy, and transmission electron microscopy. Electrochemical measurements demonstrate that the Ge/SWCNT composite paper anode with the weight percentage of 32% Ge delivered a specific discharge capacity of 417 mA h g−1 after 40 cycles at a current density of 25 mA g−1, 117% higher than the pure SWCNT paper anode. The SWCNTs not only function as a flexible mechanical support for …
Highly Conductive Carbon Nanotube-Graphene Hybrid Yarn, Javad Foroughi, Geoffrey M. Spinks, Dennis Antiohos, Azadehsadat Mirabedini, Sanjeev Gambhir, Gordon G. Wallace, Shaban Reza Ghorbani, Germanas Peleckis, Mikhail Kozlov, Marcio Lima, Ray Baughman
Highly Conductive Carbon Nanotube-Graphene Hybrid Yarn, Javad Foroughi, Geoffrey M. Spinks, Dennis Antiohos, Azadehsadat Mirabedini, Sanjeev Gambhir, Gordon G. Wallace, Shaban Reza Ghorbani, Germanas Peleckis, Mikhail Kozlov, Marcio Lima, Ray Baughman
Australian Institute for Innovative Materials - Papers
An efficient procedure for the fabrication of highly conductive carbon nanotube/graphene hybrid yarns has been developed. To start, arrays of vertically aligned multi-walled carbon nanotubes (MWNT) are converted into indefinitely long MWNT sheets by drawing. Graphene flakes are then deposited onto the MWNT sheets by electrospinning to form a composite structure that is transformed into yarn filaments by twisting. The process is scalable for yarn fabrication on an industrial scale. Prepared materials are characterized by electron microscopy, electrical, mechanical, and electrochemical measurements. It is found that the electrical conductivity of the composite MWNT-graphene yarns is over 900 S/cm. This value …
A Novel Carbon Nanotube Modified Scaffold As An Efficient Biocathode Material For Improved Microbial Electrosynthesis, Ludovic Jourdin, Stefano Freguia, Bogdan C. Donose, Jun Chen, Gordon G. Wallace, Jurg Keller, Victoria Flexer
A Novel Carbon Nanotube Modified Scaffold As An Efficient Biocathode Material For Improved Microbial Electrosynthesis, Ludovic Jourdin, Stefano Freguia, Bogdan C. Donose, Jun Chen, Gordon G. Wallace, Jurg Keller, Victoria Flexer
Australian Institute for Innovative Materials - Papers
We report on a novel biocompatible, highly conductive three-dimensional cathode manufactured by direct growth of flexible multiwalled carbon nanotubes on reticulated vitreous carbon (NanoWeb-RVC) for the improvement of microbial bioelectrosynthesis (MES). NanoWeb-RVC allows for an enhanced bacterial attachment and biofilm development within its hierarchical porous structure. 1.7 and 2.6 fold higher current density and acetate bioproduction rate normalized to total surface area were reached on NanoWeb-RVC versus a carbon plate control for the microbial reduction of carbon dioxide by mixed cultures. This is the first study showing better intrinsic efficiency as biocathode material of a three-dimensional electrode versus a flat …
Performance Enhancement Of Single-Walled Nanotube-Microwave Exfoliated Graphene Oxide Composite Electrodes Using A Stacked Electrode Configuration, Dennis Antiohos, Mark S. Romano, Joselito M. Razal, Stephen Beirne, Phil Aitchison, Andrew I. Minett, Gordon G. Wallace, Jun Chen
Performance Enhancement Of Single-Walled Nanotube-Microwave Exfoliated Graphene Oxide Composite Electrodes Using A Stacked Electrode Configuration, Dennis Antiohos, Mark S. Romano, Joselito M. Razal, Stephen Beirne, Phil Aitchison, Andrew I. Minett, Gordon G. Wallace, Jun Chen
Australian Institute for Innovative Materials - Papers
We report the development of a stacked electrode supercapacitor cell using stainless steel meshes as the current collectors and optimised single walled nanotubes (SWNT)-microwave exfoliated graphene oxide (mw rGO) composites as the electrode material. The introduction of mw rGO into a SWNT matrix creates an intertwined porous structure that enhances the electroactive surface area and capacitive performance due to the 3-D hierarchical structure that is formed. The composite structure was optimised by varying the weight ratio of the SWNTs and mw rGO. The best performing ratio was the 90% SWNT-10% mw rGO electrode which achieved a specific capacitance of 306 …
Tuning Three-Dimensional Tio2 Nanotube Electrode To Achieve High Utilization Of Ti Substrate For Lithium Storage, Zhijia Zhang, Qing-Yi Zeng, Shulei Chou, Xinjun Li, Huijun Li, Kiyoshi Ozawa, Hua-Kun Liu, Jiazhao Wang
Tuning Three-Dimensional Tio2 Nanotube Electrode To Achieve High Utilization Of Ti Substrate For Lithium Storage, Zhijia Zhang, Qing-Yi Zeng, Shulei Chou, Xinjun Li, Huijun Li, Kiyoshi Ozawa, Hua-Kun Liu, Jiazhao Wang
Australian Institute for Innovative Materials - Papers
Three-dimensional (3D) TiO2 nanotube arrays grown on Ti mesh were prepared via the anodization process. The diameters of the Ti and TiO 2/Ti wires and the length of the TiO2 nanotubes have linear relationships with the anodization processing time. When the anodization processing time is 600 min, the TiO2/Ti mesh anode materials showed good capacity retention and high specific area capacity, without the need for a current collector or binder, due to their high surface area, high substrate utilization, and large active material loading rate per unit area. At the current density of 50 μA cm-2, TiO2/Ti mesh with 600 …
Capacitive Behavior Of Latex/Single-Wall Carbon Nanotube Stretchable Electrodes, Hyeon Taek Jeong, Byung Kim, Robert Gorkin Iii, Michael J. Higgins, Gordon G. Wallace
Capacitive Behavior Of Latex/Single-Wall Carbon Nanotube Stretchable Electrodes, Hyeon Taek Jeong, Byung Kim, Robert Gorkin Iii, Michael J. Higgins, Gordon G. Wallace
Australian Institute for Innovative Materials - Papers
In this report single-wall carbon nanotubes (SWNTs) were coated onto latex using spray coating to produce a stretchable electrode. The electrochemical properties of the electrode were determined using cyclic voltammetry and electrochemical impedance spectroscopy and galvanostatic charge/discharge tests were also carried out. The impedance and charge/discharge curves of the latex/SWNTs electrode showed good capacitive behavior even after repetitive stretching to 100% strain. The highest capacitance value obtained for the unstretched SWNTs electrode was 119 F g−1 in 1 M Na2SO4 at 5 mV s−1. After the 100th stretch ≈ 80% of the original capacitance value was retained.
Fabrication Of Graphene Foam Supported Carbon Nanotube/Polyaniline Hybrids For High-Performance Supercapacitor Applications, Hongxia Yang, Nan Wang, Qun Xu, Zhimin Chen, Yumei Ren, Joselito M. Razal, Jun Chen
Fabrication Of Graphene Foam Supported Carbon Nanotube/Polyaniline Hybrids For High-Performance Supercapacitor Applications, Hongxia Yang, Nan Wang, Qun Xu, Zhimin Chen, Yumei Ren, Joselito M. Razal, Jun Chen
Australian Institute for Innovative Materials - Papers
A large-scale, high-powered energy storage system is crucial for addressing the energy problem. The development of high-performance materials is a key issue in realizing the grid-scale applications of energy-storage devices. In this work, we describe a simple and scalable method for fabricating hybrids (graphenepyrrole/ carbon nanotube-polyaniline (GPCP)) using graphene foam as the supporting template. Graphene-pyrrole (G-Py) aerogels are prepared via a green hydrothermal route from two-dimensional materials such as graphene sheets, while a carbon nanotube/polyaniline (CNT/PANI) composite dispersion is obtained via the in situ polymerization method. The functional nanohybrid materials of GPCP can be assembled by simply dipping the prepared …