Physical Sciences and Mathematics Commons^™

Impact Of The Municipal Solid Waste Incineration Plant In Warsaw On Air Quality, Robert Oleniacz

Robert Oleniacz

The only Polish municipal solid waste (MSW) incinerator has been operating within the Municipal Solid Waste Disposal Plant in Warsaw since 2000. In the paper selected results of the air quality impact assessment for this incinerator during an operating period of one year (2008) are presented. With respect to the incinerated waste amounts and emission levels, the analysed period can be considered typical for this facility. Assessment of the air quality impact was carried out by assessing air pollutant emissions in reference to the applicable emission limit values and by modeling atmospheric dispersion of these pollutants. It has been found …

Assessment Of The Impact Of Municipal Waste Incineration Plants On Air Quality And The Possibilities Of Its Reduction, Robert Oleniacz

Robert Oleniacz

The planned construction of new municipal waste incineration plants over the next few years in Poland results in protests of local communities, which arise mainly from fear of an increase in the air pollution in its vicinity. These protests extend the investment process and hinder the selection of incineration plant location, but on the other hand they necessitate the use of more efficient solutions to reduce their impact on the air quality.This paper characterizes the world's most widely used technology for municipal solid waste incineration (MSWI) and assesses the possible maximum impact on the air quality of an exemplary MSWI …

Co-Incineration Of Large Quantities Of Alternative Fuels In A Cement Kiln – The Problem Of Air Pollutant Emissions, Robert Oleniacz, Magdalena Kasietczuk

Robert Oleniacz

Over the last few years, a significant increase in the use of alternative fuels in the Polish cement industry has been observed. These are mainly waste and waste-derived fuels. The national leader in this field is Chełm cement plant (Poland), with the share of alternative fuels in the cement kiln heat balance reaching in 2012 the level of 78.5%. In this paper, an analysis of the emission rate of air pollutants from cement clinkering process in the above-mentioned cement plant in the years 1998–2012 was carried out, using the results of continuous and periodic measurements. The compliance with the emission …

Air Pollution Emissions During Baking Of Semi-Finished Graphite Products In A Tunnel Furnace, Marek Bogacki, Robert Oleniacz, Marian Mazur

Robert Oleniacz

The baking of semi-finished graphite products in a tunnel furnace is the source of many air pollutants present in both the gaseous and solid phases. The goal of this study was to assess emission rates into the air of the substances such as: CO, NOx, SO2, H2S, CH4, aliphatic hydrocarbons up to C6, benzene and its homologues (BTEX), total dust and tar substances, and polycyclic aromatic hydrocarbons (PAHs) contained in the dust. The research showed a small time-dependence of the emission rates for the majority of the substances analysed, which is, to a large extent, a result of the long …

Wpływ Procesu Współspalania Odpadów W Piecu Cementowym Na Jakość Powietrza / Impact Of Waste Co-Incineration Process In A Cement Kiln On Air Quality, Robert Oleniacz, Magdalena Kasietczuk

Robert Oleniacz

The work presents the general requirements for the control of emissions to air from waste co-combustion (co-incineration) plants, with particular emphasis on rotary kilns used for clinker production. Air emissions from the cement kiln during co-combustion of alternative fuels and the impact assessment on air quality are also presented. The object of the study was one of the Polish cement plant, which uses significant amounts of solid waste derived fuels (with over 70% share in the cement kiln heat balance). Assessment of the impact on air quality was made based on the results of the modeling of atmospheric dispersion of …

Emisja Zanieczyszczeń Pyłowo-Gazowych Z Procesu Wypalania Półproduktów Grafitowych W Piecu Tunelowym, Marek Bogacki, Robert Oleniacz, Marian Mazur, Przemysław Szczygłowski

Robert Oleniacz

The baking of semi-finished graphite products in a tunnel furnace is the source of many air pollutants present in both the gaseous and solid phases. The goal of this study was to assess emission rates into the air of the substances such as: CO, NOx, SO2, H2S, CH4, aliphatic hydrocarbons up to C6, benzene and its homologues (BTEX), total dust and tar substances, and polycyclic aromatic hydrocarbons (PAHs) contained in the dust. The research showed a small time-dependence of the emission rates for the majority of the substances analysed, which is, to a large extent, a result of the long …

Air Pollutant Emissions From Process Of Mixing Materials Used For Manufacturing Small Products From Carbon And Graphite, Marian Mazur, Marek Bogacki, Robert Oleniacz, Przemysław Szczygłowski

Robert Oleniacz

The paper characterises the method of preparing the HCC and Rubba-type materials used to manufacture small carbon and graphite products, and the composition of waste gases escaping from the mixers for these materials. For the process of mixing the two materials under examination, two measurement series were completed, mainly covering the period from when the binder was added to the properly pre-heated dry mass until the mixer discharged. The results shown apply only to those substances which occur just in the gaseous phase, that is CO, CO2, O2, H2, aliphatic hydrocarbons (C1-C6) and BTX (benzene, toluene, ethylbenzene and xylene) as …

Ocena Skuteczności Działania Suchego Systemu Oczyszczania Spalin Ze Spalania Odpadów Medycznych Opartego Na Wtrysku Sorbentu Wapniowo-Węglowego, Robert Oleniacz

Robert Oleniacz

The research object was a medical waste incineration plant with a capacity of 150 kg per hour equipped with a flue gas treatment system based on dry sorption process using a lime-carbon reagent with adsorbent removing in high-efficiency particulate collector. As the dry sorption agent was used a mixture of high reactive hydrated lime and activated carbon injected to combustion gases by pneumatic feeder. Activated carbon content in the mixture was 5-10 % by mass. Applied collector was ceramic filter with total filtration area of 120 m2 and guaranteed outlet dust concentration under 5 mg/Nm3. Among others things the aims …

Wpływ Dużej Spalarni Odpadów Przemysłowych I Niebezpiecznych Na Jakość Powietrza, Robert Oleniacz, Lidia Rusztowicz

Robert Oleniacz

Waste incineration causes unavoidable pollutant emissions to atmosphere and thus negative impact on air quality, but scale of the influence is often exaggerated. In the paper computation results of the atmospheric dispersion of pollutants were presented for one of the largest industrial and hazardous waste incineration plant existing in Poland (processing capacity: 3 ton per hour). These results confirm the fact that the incinerator meets the requirements of best available techniques (BAT) for the waste incineration and its impact on air quality is relatively small. This effect is caused mainly by proper operation of the rotary kiln incinerator, high efficiency …

Analiza Możliwości Ograniczenia Emisji Zanieczyszczeń Powietrza Z Instalacji Spalania Odpadów Medycznych W Tarnowie, Robert Oleniacz

Robert Oleniacz

The paper presents initial research of effects of some factors on the amount of gaseous pollutants formation during medical waste incineration in a two-stage starved air fluidised bed reactor. In the research was included the impact of such factors as oxygen contents in flue gases, frequency of waste loading, momentary mass flow of waste and temperature in the secondary combustion chambers. Measurements showed that the waste incineration in large amount periodically caused excessive emissions incomplete combustion products (CO, HC), especially during wrong operation of the combustion system. The work demonstrated that the essential importance for CO and HC formation reducing …

Emisja Zanieczyszczeń Z Procesu Grafityzacji Elektrod Węglowych W Piecach Lwg (Castnera). Cz. 2. Wybrane Substancje Pyłowe, Marian Mazur, Robert Oleniacz, Marek Bogacki, Przemysław Szczygłowski

Robert Oleniacz

The measurement results of quantity of dust pollutants originated and emitted to air from LWG (Castner) furnaces during graphitisation process of coal electrodes were presented in the paper. The investigation was carried out for total dust, total tar substances and polycyclic aromatic hydrocarbons (PAHs). The measurements were performed both before and after the flue gas control system (catalytic burning and wet cleaning). Thus changes of the substance concentrations in the gases for the cleaning system were estimated. As a result of the investigation was conclusion that the graphite process of coal electrodes in LWG stoves is not a significant source …

Emisja Zanieczyszczeń Z Pieca Achesona Do Grafityzacji Wyrobów Drobnych, Marian Mazur, Robert Oleniacz, Marek Bogacki, Przemysław Szczygłowski

Robert Oleniacz

Research results of the air pollutant emissions from the graphitisation process of fine products in the Acheson electric resistance furnace (discharge capacity 5,5 Mg) were presented in the paper. Research was performed for two kinds of raw material inputs (based on petroleum coke and pitch coke). Approximately 40-hours measurement series were carried out for each material including mainly such substances like carbon monoxide, hydrocarbons, nitrogen oxides, sulphur dioxide, hydrogen sulphide, carbon disulphide, ammonia, benzene, toluene, xylenes, total dust, tar substances and polycyclic aromatic hydrocarbons. Both average and maximum concentrations and mass streams in the flue gases and average emission factors …

Emisja Zanieczyszczeń Ze Spalania Odpadów Podestylacyjnych Z Produkcji Witaminy C W Piecu Fluidalnym, Robert Oleniacz

Robert Oleniacz

Some results of continuous or periodical measurements of selected air pollutant concentrations and mass streams in the flue gases from liquid waste incineration in a fluidized bed incinerator were presented in the paper. During the researches distillation tails from vitamin C production, that is waste traces from regeneration such solvents as for example ethylene chloride, chloroform or trichloroethylene were incinerated. As a result of the researches there was determined optimal temperature of the fluidized bad in which the waste incineration should be carried out to minimization of CO and NOx formation. Required effectiveness of HCl removal from combustion gases to …

Emisja Zanieczyszczeń Z Procesu Grafityzacji Elektrod Węglowych W Piecach Lwg (Castnera). Cz. 1. Wybrane Substancje Gazowe, Marian Mazur, Robert Oleniacz, Marek Bogacki, Przemysław Szczygłowski

Robert Oleniacz

The results of measurements of quantity pollutants originated and emitted to air from LWG (Castner) furnaces were introduced. The investigation was carried out during the graphitisation process of coal electrodes, until moment of end of ventilation the stove across applied installations of cleaning of cool gases (catalytic burning and the wet desulphurization). The measurement results of CO, CO2, HC+H2, SO2, H2S, CS2, NO, NO2, NH3 as well as chosen hydrocarbons (C1-C6) and aromatic hydrocarbons (BTX) were presented. In result of conducted investigations was qualified courses of changeability of concentrations in gases these substances before and for the cleaning system. The …

Emisja Chlorowodoru Ze Spalania Węgla W Kotle Pyłowym, Marian Mazur, Robert Oleniacz, Przemysław Szczygłowski, Marek Bogacki

Robert Oleniacz

Emission of hydrogen chloride (HCl) from coal combustion is not controlled just like for example sulpfur dioxide emission. But HCl emission is also important, because chlorine content in some types of coal can reach the similar level to sulfur content. In the paper the measurement results of HCl emission to the air during combustion of three types of coal with law content of chlorine were presented. The researches were carried out for a steam pulverized coal boiler (max. boiler efficiency – 430 t/h) during three various loads (respectively 65, 80 and 95 % of maximum efficiency) without flue gas desulfurization. …

Emisja Btx Towarzysząca Produkcji Wyrobów Węglowych I Grafitowych, Marian Mazur, Przemysław Szczygłowski, Robert Oleniacz, Marek Bogacki

Robert Oleniacz

The work presents results of direct measurements of benzene, toluene, ethyl benzene and xylenes (BTX or BTEX) emissions to the air from technological processes related with carbon and graphite manufacturing. The most important from all mentioned pollutants is benzene considered as one of the main factor of air pollution in the European Union. The highest concentrations of BTX were found in the fumes emitted from the tanks of liquid raw materials, while the highest levels of their emissions were from furnaces used for baking of green electrodes and other carbon products.

English title: BTX emission from production of graphite and …

Termiczne Przekształcanie Odpadów Medycznych W Instalacji Fluidalnej Firmy Seghers – Emisja Zanieczyszczeń Gazowych I Możliwości Jej Ograniczenia, Robert Oleniacz

Robert Oleniacz

The paper presents the results of measurements of concentrations and mass streams of selected components in the flue gases from the thermal treatment of medical waste in the Seghers incinerator based on fluidized bed reactor.

The tests were carried out at the measuring points located both before and after of the flue-gas cleaning system based on the injection of dry hydrated lime and carbon sorbent and a ceramic filter. In this way it was possible to determine the effectiveness of the removal of selected air pollutants in the dry cleaning system. Analysis of the results of measurements made ​​it possible …

Przebieg Zmienności Stężeń Wybranych Zanieczyszczeń W Gazach Odlotowych Z Procesu Mokrego Gaszenia Koksu, Marian Mazur, Robert Oleniacz, Marek Bogacki

Robert Oleniacz

Continuous measurement results of selected constituent concentrations in the gases emitted to the air during the coke wet quenching process were presented and discussed in the paper. The measurements were carried out for the standard wet quenching tower. The research covered such substances as carbon dioxide, carbon monoxide, hydrogen sulfide, nitrogen oxide, nitrogen dioxide and a total content of hydrocarbons and hydrogen (combustible gases). Changeability of the substance concentrations depending of the quenching process duration was analyzed. Among other things the beginning of these substances formation, appearance of the maximum and the range of observed concentrations were taken into consideration. …

Weryfikacja Emisji Pyłowej Z Huty Katowice I Zasięgu Jej Oddziaływania, Marian Mazur, Robert Oleniacz, Marek Bogacki, Agnieszka Łopata

Robert Oleniacz

Preliminary analysis of the results of atmospheric dispersion modeling for dust emission from the Katowice Steelworks (Poland) showed necessity of verification the particulate matter, lead and cadmium emission from the plant. The verification was limited to the substance emission sources influencing air pollution to the largest extent. Both scale of dust emission and its granulometric and chemical composition were re-evaluated. Further calculations of the air propagation for the pollutants were carried out and calculation results were compared with direct measurements. Thus the Katowice Steelworks impact on air quality and the level of total dust, lead and cadmium ground deposition was …

Czynniki Wpływające Na Skład Spalin I Wielkość Emisji Zanieczyszczeń Z Procesów Termicznego Przekształcania Odpadów Niebezpiecznych, Robert Oleniacz

Robert Oleniacz

The work summarizes factors influencing on air emissions from various full-scale hazardous waste incinerators (rotary kiln, multiple hearth furnace, starved-air incinerator, fluidized bed incinerator, liquid injection incinerator). Air pollutant emissions from hazardous waste incineration can be minimized not only by flue-gas cleaning. There are many factors that influence on flue-gas composition and the quantity of air pollutants formed during incineration: the type, the composition and the quantity of waste, the way of waste introducing to the incinerator, excess air ratio, combustion temperature, retention time of exhaust gases etc. Special attention was paid to the loading of waste and incineration conditions …

Struktura Emisji Związków Fluoru Z Hutnictwa Żelaza Na Przykładzie Huty Katowice, Marian Mazur, Robert Oleniacz, Marek Bogacki

Robert Oleniacz

As recently as a dozen or so years ago ferrous metallurgy was known as one of the biggest source of fluorine compound emissions to the atmosphere. Nevertheless production technology and raw material changes occurring in this industry cause continuous decreasing of their participation in the total fluorine emission. On the ground of investigations that have been carried out in the Katowice Steelworks (Poland) in the last few years, participation of particular technological processing in the water-soluble fluorine compound emissions (which are regarded as toxic) were presented in the paper, as well as a position of fuel combustion process (that take …

Emisja Związków Fluoru Z Hutnictwa Żelaza, Marian Mazur, Marek Bogacki, Robert Oleniacz

Robert Oleniacz

The article presents the results of the last few years of comprehensive researches related to the emission of fluorine compounds from iron metallurgy in Poland. Determined of the levels of flue-gas concentrations and air emissions for fluorine in the form of gaseous and solid compounds, including water-soluble compounds (considered to be toxic). The study also made it possible to analyze of raw materials used in these processes taking into account fluorine content and its impact on the amount of fluorine compounds emitted to the air.

English title: Emissions of fluorine compounds with iron metallurgy.

Spalanie Odpadów Niebezpiecznych W Piecach Cementowych. Część 2. Destrukcja Paliwa I Emisja Zanieczyszczeń, Robert Oleniacz

Robert Oleniacz

Conditions occurring in cement rotary kilns assure high destruction and removal efficiency (DRE) of the most stable substances, efficacious dry sorption of acid gases in the alkaline raw meal and heavy metals bounding in the clinker. Adequate operation of hazardous waste incineration in the process connected with cement clinker production does not cause increasing air pollutant emissions. Magnitude of the emissions often does not depend of this if there are using wastes in the cement kiln at all. The work presents a review of DRE levels and stack emissions for selected flue-gas constituents during hazardous waste co-combustion in cement kilns …

Emisja Zanieczyszczeń Ze Spalania Odpadów Niebezpiecznych W Piecu Obrotowym, Robert Oleniacz, Marian Mazur, Marek Bogacki

Robert Oleniacz

The article presents measurement results of air pollutant emissions from incineration of selected hazardous wastes in a full-scale rotary kiln equipped with afterburner and a wet installation for flue gas cleaning. This type of kiln is suitable for thermal disposal of many sorts of wastes, both solid and liquid. Four groups of waste were being incinerated during the tests: coke tars, medical (hospital) and pharmaceutical wastes added to greased cleaning materials, a sawdust and used gloves, varnish and lubrication wastes, as well as waste rubber and resins. The study was performed in order to answer the question: is the process …

Emisja Metali Ciężkich Ze Spalania Odpadów Niebezpiecznych, Robert Oleniacz, Marian Mazur, Marek Bogacki

Robert Oleniacz

The paper presents the results of measurements of air emissions of heavy metals from hazardous waste incineration in a multiple hearth furnace and a rotary kiln incinerator equipped with a single wet flue gas cleaning systems. In the multiple hearth furnace an industrial sewage sludge (from coke industry) was being incinerated. In the rotary kiln such wastes were being incinerated as: waste paints, varnish and lubricant, coal tars waste, contaminated cleaning rags, sawdust and used gloves, waste resins and plastics, rubber waste, outdated pharmaceuticals and medicines, and hospital waste. The research allowed us to determine the levels of pollutant concentrations …

Spalanie Odpadów Poszpitalnych I Farmaceutycznych W Piecu Obrotowym / Incineration Of Hospital And Pharmaceutical Wastes In A Rotary Kiln Incinerator, Robert Oleniacz, Marian Mazur, Marek Bogacki

Robert Oleniacz

The paper presents selected results of research on hospital and pharmaceutical waste incineration in a full-scale rotary kiln with variable loads of the kiln. As part of these studies measurements of air pollutant concentrations in flue gases and leaching tests of solid combustion products were carried out. Based on these studies, the maximum dose of hospital and pharmaceutical waste was proposed in the mixture with industrial wastes, which does not cause excessive air emissions. The average emission factors for the waste mixture loading were also determined.

Emisja Zanieczyszczeń Ze Spalania Odpadów Ściekowych W Piecu Półkowym, Robert Oleniacz, Marian Mazur, Marek Bogacki

Robert Oleniacz

The article presents incineration tests of silty-tar sludge produced in the wastewater treatment plant for coke industry. Sewage sludges were incinerated in a full-scale multiple hearth incinerator equipped with a wet flue-gas cleaning system (alkaline scrubber). Measurements of air pollutant emissions were carried out both before and after the cleaning system. The obtained results allow to conclude that the thermal utilization of sewage sludge in this type of installation might be just a little cumbersome for the environment, using the appropriate equipment for the purification of exhaust gases. The paper also specifies minimum exhaust gas cleaning performance that guarantees compliance …

Emisja Zanieczyszczeń Ze Spalania Odpadów Przemysłowych W Piecu Obrotowym, Robert Oleniacz, Marian Mazur, Marek Bogacki

Robert Oleniacz

The paper presents the results of measurements of the concentration of selected pollutants in the flue gases from the incineration of industrial wastes in a full-scale rotary kiln. The study included three waste mixtures introduced into the kiln: 1) coal tar waste (tar origin of coke); 1) waste paints, varnish and lubricant; 3) resin and rubber waste. The article also assesses the effectiveness of the existing wet flue gas cleaning system (alkaline scrubber) and specifies minimum exhaust gas purifying performance guarantees compliance with European emission standards for waste incineration.

English title: Pollutant emissions from incineration of industrial waste in a …

Emisja Chlorowodoru I Związków Fluoru Ze Spalania Odpadów Niebezpiecznych, Marian Mazur, Robert Oleniacz, Marek Bogacki

Robert Oleniacz

The paper presents the results of measurements of the concentration of hydrogen chloride (HCl) and fluoride compounds (as HF) in raw and purified combustion gases discharged from the incineration of selected hazardous wastes. The study included two installations operating on an industrial scale: a multiple hearth furnace and a rotary kiln incinerator equipped with a single wet flue gas cleaning systems. In the multiple hearth furnace was being incinerated sludge from coke industry. In the rotary kiln were being incinerated coal (coke) tars, contaminated cleaning rags, sawdust, used gloves, outdated pharmaceuticals and medicines, hospital waste, waste paints, varnish and lubricant, …

Termiczna Utylizacja Odpadów W Spalarni "Lobbe" W Dąbrowie Górniczej – Problemy Emisji Zanieczyszczeń, Marian Mazur, Ryszard Januszek, Robert Oleniacz

Robert Oleniacz

The paper presents selected results of comprehensive studies of air quality impact assessment carried out for the „LOBBE” incineration plant in Dąbrowa Górnicza (Poland) in 1995. It focused mainly on air emissions problems. Stack concentrations and emissions of selected air pollutants formed during thermal treatment processes of different kinds of waste materials and incinerators is performed. The study covered both sludge and slime incinerated in a multiple hearth furnace and four example groups of waste materials incinerated in a rotary furnace. The research have helped confirm the levels of air emissions as a function of the type of incinerated waste …