Physical Sciences and Mathematics Commons^™

Use Of Sodium Bismuthate Chromatography For Separation Of Americium From Curium And Other Elements In Spent Nuclear Fuel, Jason Michael Richards

UNLV Theses, Dissertations, Professional Papers, and Capstones

A novel method for partitioning americium from curium has been developed using sodium bismuthate as both an oxidant and a separation medium. The presence of americium and curium in nuclear waste increases the heat load in geological repositories and leads to larger waste volumes. These elements are also the source of most of the long-term radiotoxicity of the waste. However, the heat load and long-term radiotoxicity contribution from americium is much greater than that from curium. The contribution of curium to the heat load and radiotoxicity of the waste is significant on the same time scale as longer-lived fission products …

Solvent Extraction And Extraction Chromatography Of Homologs And Pseudohomologs Of Rutherfordium Using Teha And Tehp, Jeffrey Rolfes

UNLV Theses, Dissertations, Professional Papers, and Capstones

Studies of the chemical properties of the heaviest elements have always been difficult due to the short half-lives and low cross sections involved. To solve this problem, atom-at-a-time methods are necessary to determine the properties of these short-lived isotopes. Extremely fast kinetics for the chemical reactions studied (on the same order as the nuclide’s half-life) are required, and the system should have the potential for automation. Solvent extraction, with its selectivity and quick kinetics, has historically been used for these investigations into characteristics of super heavy elements. Another technique, extraction chromatography, offers potentially a way of investigating rutherfordium’s properties, without …

Development Of Chemical Separation Methods Using Transition Metals For Nuclear Forensic And Medicinal Applications, Lucas Peter Boron-Brenner

UNLV Theses, Dissertations, Professional Papers, and Capstones

Insufficient data exists on the effects of prompt fast neutron activation on metals found commonly in nuclear devices and the urban environment. Different metals such as Ti, Au, Fe, and Cu were activated using the Flattop Criticality Benchmark at the Device Assembly Facility on the Nevada Test Site using a known neutron spectrum and flux to determine a baseline cross section value. Cross section information gathered from these neutron activation measurements could provide information that helps government and law enforcement agencies to correctly trace the origin of a nuclear device’s fuel or component features.

Based on activation products produced in …

Development Of Microdialysis Probes In Series Approach Toward Eliminating Microdialysis Sampling Calibration: Miniaturization Into A Pdms Microfluidic Device, Randy Espinal Cabrera

Graduate Theses and Dissertations

A new microdialysis sampling method and microfluidic device were developed in vitro. The method consisted of using up to four microdialysis sampling probes connected in series to evaluate the relative recovery (RR) of different model solutes methyl orange, fluorescein isothiocyanate (FITC)-dextran average mol. wt. 4,000 (FITC-4), FITC-10, FITC-20, and FITC-40. Different flow rates (0.8, 1.0, and 1.5 µL/min) were used to compare experimentally observed relative recoveries with theoretical estimations. With increasing the number of probes in series, the relative recovery increases and ~100% (99.7% ± 0.9%) relative recovery for methyl orange was obtained. For larger molecules such as fluorescein isothiocyanate …

Designed Polymer Brush Interfaces For Plutonium Separations And Polyethylene Nanocomposites, Julia G. Pribyl

Theses and Dissertations

Modification of surfaces with polymer brushes has become an important area of research for developing materials with a variety of advanced properties. Flat or continuous surfaces modified with polymer brushes can serve as surfaces where chemical reactions or separations take place, and discrete nanoparticles covered in a polymer brush can disperse within a miscible surrounding polymer, generating a composite which retains the processability of the polymer but becomes endowed with the properties of the filler as well. Presented herein are new synthetic approaches to modify both continuous surfaces as well as discrete particles with polymer brushes for complex applications. In …