Occupational Health and Industrial Hygiene Commons^™

Noise Induced Hearing Loss Accountability On Jobsites Within The Construction Industry, Joseph O. Lamphere

Construction Management

Noise induced hearing loss is a major issue on jobsites within the construction industry. Every day workers are exposed to hazardous levels of noise, but they are not being properly managed to mitigate this issue. Workers have misconceptions about the topic, but more surprisingly are sometimes indifferent to the effects; believing hearing loss is inevitable, or it can be cured with a hearing aide. Construction has inherent dangers that workers have to deal with every day. Hearing loss might not be on the top of their lists, but the effects are permanent, and they cannot be cured with a hearing …

Nanoparticle Penetration Of Respirator Masks At Construction Sites, Jefferson W. Doehling

Honors College Theses

This experimental investigation studies the effectiveness of N95 respirators at blocking particles between 11.5 and 154 nm in diameter during 4 different construction activities. It is well known that large amounts of dust and debris are generated during construction activities. New research has found that significantly more nanoparticles are generated during construction activities than previously thought. Consequently, the N95 respirators commonly worn to protect against these particles are only rated to block 95% particles larger than 0.3 microns in size. In this investigation, two respirator models were tested, a NIOSH TC-84A-0007 pleated N95 respirator and a NIOSH 42CFR84 foldable N95 …

Assessment Of Ergonomics In Indian Dental Practice: A Workplace Analysis, Divya Gadde

Masters Theses & Specialist Projects

Dental practice requires unique working conditions such as prolonged working hours, strained body postures and laborious, high finesse dental techniques. However, it can be more efficiently performed by the application of ergonomics, rather than physically forcing the worker's body to fit the job. Posture is highly influenced by factors such as inadequate working level, incorrect patient positioning, and poor visual comfort. In order to eliminate musculoskeletal disorders it is necessary to control these and other factors, and design the human work environment to be more ergonomic. The aim of this study was to assess ergonomics within Indian dental practice and …

Occupational Noise Dose Reduction Via Behavior Modification Using In-Ear Dosimetry Among Usaf Personnel Exposed To Continuous Impulse Noise, Jesse A. Trawick

Theses and Dissertations

The purpose of this research was to investigate the use of in-ear noise dosimetry and worker feedback to reduce noise exposures among combat arms instructors and heavy equipment operators in the Air Force. Specifically, this thesis sought to determine how effectively hearing protection devices (HPDs) are being utilized currently, and whether providing at-ear noise exposure data to workers results in reduced noise exposures or changes in worker attitude. These questions were addressed by performing a six-month field study using dosimeters to record worker noise exposures under HPDs. Subjects served as their own control, receiving feedback in only the latter half …

Effects Of Motion Segment Simulation And Joint Positioning On Spinal Loads In Trunk Musculoskeletal Models, F. Ghezelbash, A. H. Eskandari, A. Shirazi-Adl, N. Arjmand, Z. El Ouaaid, A. Plamondon

Études primaires

Musculoskeletal models represent spinal motion segments by spherical joints/beams with linear/nonlinear properties placed at various locations. We investigated the fidelity of these simplified models (i.e., spherical joints with/without rotational springs and beams considering nonlinear/linear properties) in predicting kinematics of the ligamentous spine in comparison with a detailed finite element (FE) model while considering various anterior-posterior joint placements. Using the simplified models with different joint offsets in a subject-specific musculoskeletal model, we computed local spinal forces during forward flexion and compared results with intradiscal pressure measurements. In comparison to the detailed FE model, linearized beam and spherical joint models failed to …

Improving Workers' Safety And Health In The Zimbabwean Mining And Quarrying Industry, Bernard Mabika

Walden Dissertations and Doctoral Studies

Lack of effective occupational safety and health (OSH) strategies is a reason that

workplace accidents in the mining and quarrying industry remain high, making the

industry one of the riskiest operations worldwide. The purpose of this multiple case study

was to explore successful strategies mining and quarrying leaders in Zimbabwe used to

improve OSH. The key research question addressed successful strategies leaders in the

mining and quarrying industry use to improve employee occupational safety and health in

Zimbabwe. Six successful business leaders from 3 mining and quarrying mines in

Zimbabwe demonstrated an exception to unsafe practices, particularly through their

exceptional …

Characterization Of Jet Fuel Combustion Emissions During A C-130 Aeromedical Evacuation Engines Running Onload, Michelle L. Page

Theses and Dissertations

The purpose of this research was to characterize jet fuel combustion emissions (JFCE) in an occupational setting. Prior research demonstrated that aircraft emit hazardous species, especially at engine start-up and ground idle. Complaints of eye, nose, and throat irritation from occupational exposures near aircraft exist. In this study JFCE were tested during an aeromedical evacuation engines running patient onload (ERO) on a C-130 Hercules at the 179^th Airlift Wing, Mansfield-Lahm Air National Guard. Ultrafine particles, VOC, formaldehyde, carbon monoxide (CO), sulfuric acid, and metals were sampled simultaneously in approximate crew and patient breathing zones. Testing methods were portable condensation …

The Effect Of Magnification Loupes On Dental Hygienists' Posture While Exploring, Emily Ludwig, Gayle B. Mccombs, Susan L. Tolle, Daniel M. Russell

Dental Hygiene Faculty Publications

Purpose: The purpose of this study was to determine the effects of dental magnification loupes on posture during instrumentation.

Methods: A convenience sample of 27 right-handed dental hygienists, with no prior history of injuries or disabilities of the head, neck, or trunk region, enrolled in the study. Baseline posture calibration was taken and tri-axial accelerometers were placed on four locations of the head and trunk (occipital region of head; cervical vertebrae C5; thoracic vertebrae T5; lumbar vertebrae L1) to measure acceleration and the orientation of the body to gravity. Participants were randomly assigned to wear self-supplied magnification loupes during either …

Optimal Configurations For Aerosol Monitoring With Multi-Rotor Small Unmanned Aerial Systems, Inna D. Chavez

Theses and Dissertations

Applicability of aerosol sampling on multi-rotor unmanned aerial systems (UAS) platform was investigated. Multi-rotor UAS have impacts of wind speed, turbulence, and orientation possibly contributing to sampling bias. The SKC IMPACT sampler, Tecora C.A.Th.I.A., and modified three-dimensionally printed Universal Inlet for Airborne-Particle Size-Selective Sampling were selected based on particle size-selectivity and operational independence to wind. Airflow visualizations concluded that below UAS fuselage was optimal sampler placement. Tests were conducted with Arizona Road Dust in a still-air chamber, and aerosolized sugar in a wind tunnel. Inlet mounting was evaluated in, upright, upside-down, and horizontal orientations. Horizontal orientations of all inlets resulted …

Development Of A Medium Scale Apparatus For Testing & Teaching Dispersed Dust Flame Effects, David Petrow

Online Theses and Dissertations

Combustible dust explosions and flash fires are a leading cause of property damage, injuries, and death in industries around the world. An example of a disastrous dust explosion occurred at CTA Acoustics in Corbin, KY in 2003. This explosion cost the lives of seven workers and injured 37 more. A mobile inexpensive dust dispersion apparatus (DDA) was designed, built, and tested to reproduce medium scale dust flash fires. By using fuel amounts varying from 0.45kg to 4.54kg the DDA created dust clouds ranging from 2.5m to 7.5m in diameter. With these measurements, the characterization of dust hazards and validation of …

Accuracy And Repeatability Of Single-Pose Calibration Of Inertial Measurement Units For Whole-Body Motion Analysis, Xavier Robert-Lachaine, Hakim Mecheri, Christian Larue, André Plamondon

Études primaires

Portable inertial measurement units (IMUs) are suitable for motion analysis outside the laboratory. However, IMUs depend on the calibration of each body segment to measure human movement. Different calibration approaches have been developed for simplicity of use or similarity to laboratory motion analysis, but they have not been extensively examined. The main objective of the study was to determine the accuracy and repeatability of two common single-pose calibrations (N-pose and T-pose) under different conditions of placement (self-placement and passive placement), as well as their similarity to laboratory analysis based on anatomical landmarks. A further aim of the study was to …

Difference Between Male And Female Workers Lifting The Same Relative Load When Palletizing Boxes, André Plamondon, Christian Larivière, Denys Denis, Hakim Mecheri, Iuliana Nastasia

Études primaires

A few biomechanical studies have contrasted the work techniques of female and male workers during manual material handling (MMH). A recent study showed that female workers differed from males mostly in the strategy they used to lift 15-kg boxes from the ground, especially regarding task duration, knee and back postures and interjoint coordination. However, the lifting technique difference observed in females compared to males was perhaps due to a strength differences. The objective of this study was to test whether female workers would repeat the same lifting technique with a load adjusted to their overall strength (females: 10 kg; males: …

Effect Of Local Magnetic Field Disturbances On Inertial Measurement Units Accuracy, Xavier Robert-Lachaine, Hakim Mecheri, Christian Larue, André Plamondon

Études primaires

Inertial measurement units (IMUs), a practical motion analysis technology for field acquisition, have magnetometers to improve segment orientation estimation. However, sensitivity to magnetic disturbances can affect their accuracy. The objective of this study was to determine the joint angles accuracy of IMUs under different timing of magnetic disturbances of various durations and to evaluate a few correction methods. Kinematics from 12 individuals were obtained simultaneously with an Xsens system where an Optotrak cluster acting as the reference system was affixed to each IMU. A handling task was executed under normal laboratory conditions and imposed magnetic disturbances. Joint angle RMSE was …

Validation Of Inertial Measurement Units With An Optoelectronic System For Whole-Body Motion Analysis, Xavier Robert-Lachaine, Hakim Mecheri, Christian Larue, André Plamondon

Études primaires

The potential of inertial measurement units (IMUs) for ergonomics applications appears promising. However, previous IMUs validation studies have been incomplete regarding aspects of joints analysed, complexity of movements and duration of trials. The objective was to determine the technological error and biomechanical model differences between IMUs and an optoelectronic system and evaluate the effect of task complexity and duration. Whole-body kinematics from 12 participants was recorded simultaneously with a full-body Xsens system where an Optotrak cluster was fixed on every IMU. Short functional movements and long manual material handling tasks were performed and joint angles were compared between the two …

Exploring The Cause Of Injury Or Death In Grain Entrapment, Engulfment And Extrication, Salah F. Issa

Open Access Dissertations

Grain entrapments and engulfments are one of most common hazards associated with grain storage facilities. Since the 1970’s over 1,880 incidents have been documented in agricultural confined spaces of which 65% of all recorded incidents were grain entrapments and engulfments. There have been several studies conducted on the contributing factors behind these incidents; however, there have been very few attempts to understand the environmental, physiological or psychological factors the victims experience while entrapped, engulfed, or extricated. This includes understanding how secondary injuries are caused by grain or during extrication by first responders. The research effort was divided into three segments. …

Use Of A Modified Greenscreen Tool To Conduct A Screening-Level Comparative Hazard Assessment Of Conventional Silver And Two Forms Of Nanosilver., Jennifer Sass, Lauren Heine, Nina Hwang

Environmental and Occupational Health Faculty Publications

BACKGROUND: Increased concern for potential health and environmental impacts of chemicals, including nanomaterials, in consumer products is driving demand for greater transparency regarding potential risks. Chemical hazard assessment is a powerful tool to inform product design, development and procurement and has been integrated into alternative assessment frameworks. The extent to which assessment methods originally designed for conventionally-sized materials can be used for nanomaterials, which have size-dependent physical and chemical properties, have not been well established. We contracted with a certified GreenScreen profiler to conduct three GreenScreen hazard assessments, for conventional silver and two forms of nanosilver. The contractor summarized publicly …

A Biomechanical Comparison Between Expert And Novice Manual Materials Handlers Using A Multi-Joint Emg-Assisted Optimization Musculoskeletal Model Of The Lumbar Spine, Denis Gagnon, André Plamondon, Christian Larivière

Études primaires

Expertise is a key factor modulating the risk of low back disorders (LBD). Through years of practice in the workplace, the typical expert acquires high level specific skills and maintains a clean record of work-related injuries. Ergonomic observations of manual materials handling (MMH) tasks show that expert techniques differ from those of novices, leading to the idea that expert techniques are safer. Biomechanical studies of MMH tasks performed by experts/novices report mixed results for kinematic/kinetic variables, evoking potential internal effect of expertise. In the context of series of box transfers simulated by actual workers, detailed internal loads predicted by a …

Subject-Specific Biomechanics Of Trunk: Musculoskeletal Scaling, Internal Loads And Intradiscal Pressure Estimation, F. Ghezelbash, A. Shirazi-Adl, N. Arjmand, Z. El-Ouaaid, A. Plamondon

Études primaires

Development of a subject-specific computational musculoskeletal trunk model (accounting for age, sex, body weight and body height), estimation of muscle forces and internal loads as well as subsequent validation by comparison with measured intradiscal pressure in various lifting tasks are novel, important and challenging. The objective of the present study is twofold. First, it aims to update and personalize the passive and active structures in an existing musculoskeletal kinematics-driven finite element model. The scaling scheme used an existing imaging database and biomechanical principles to adjust muscle geometries/cross-sectional-areas and passive joint geometry/properties in accordance with subjects’ sex, age, body weight and …

Student Absenteeism And The Comparisons Of Two Sampling Procedures For Culturable Bioaerosol Measurement In Classrooms With And Without Upper Room Ultraviolet Germicidal Irradiation Devices, Chunxiao Su, Josephine Lau, Shawn G. Gibbs

Durham School of Architectural Engineering and Construction: Faculty Publications

Upper room ultraviolet germicidal irradiance (UVGI) has been shown to reduce the concentration of bioaerosols in controlled chambers. However, there is a lack of experimental results on the reduction of bioaerosol concentrations by UVGI devices in actual uncontrolled buildings. This study was carried out in an American elementary school in the Midwest. Two sampling procedures were carried out in six selected classrooms with similar dimensions that were separated into two groups: (1) UVGI exposure group and (2) non-UVGI control group. Two-stage Tisch culturable impactors were utilized to collect airborne culturable bacteria and fungi. Monthly samples were collected during unoccupied period …

Review Of Sampling And Evaluation Techniques For Diesel Exhaust Particulate Matter In The Mining Industry And The Application Of A Vapor Phase Organic Carbon Correction Factor, Ryley Bosch

Graduate Theses & Non-Theses

The health effects associated with diesel exhaust exposure have been documented for decades. However, methods used to assess diesel exhaust have experienced considerable revision over the past twenty years. The latest sampling methodology considers particulate matter elemental carbon (EC) and organic carbon (OC) analysis along with the vapor phase OC analysis. The objective of this study was to evaluate the influence of vapor phase OC on the current National Institute for Occupational Safety and Health (NIOSH) method 5040 sampling and evaluation techniques for diesel exhaust particulate matter.

A pilot study was conducted as part of a larger study evaluation biodiesel …

An Evaluation Of Carbon Concentrations Associated With Biodiesel Particulate Matter In An Underground Metal Mine, David Evans

Graduate Theses & Non-Theses

Exposure to diesel particulate matter from diesel exhaust has been shown to have adverse health effects in humans. In 2012 The International Agency for Research on Cancer classified diesel exhaust as a group 1 know human carcinogen. Because of the associated health effects, there has been a strong push to reduce the amount of diesel exhaust present in the mining industry. Biodiesel is one to the more common and promising control options used to reduce the amount of diesel particulate matter that is generated during fuel combustion. The use of biodiesel over petroleum diesel has been shown to reduce not …

An Axisymmetric Finite Element Model To Study The Earplug Contribution To The Bone Conduction Occlusion Effect, Martin K. Brummund, Franck Sgard, Yvan Petit, Frédéric Laville, Hugues Nélisse

Études primaires

An axisymmetric linear elasto-acoustic finite element (FE) model of an occluded human external ear is proposed to simulate the bone conduction occlusion effect (OE). The model consists of a cylindrical ear canal cavity surrounded by layers of biological tissues (skin, cartilage and bone) in which an earplug is inserted. Geometrical and material properties are taken from the literature. OEs are predicted for foam and silicone earplug FE-models using COMSOL Multiphysics (COMSOL®, Sweden). The FE-model is shown to predict the experimental OE measured in two healthy human reference groups wearing foam or silicone earplugs, satisfactorily. Deviations between model and experiment are …

Exposure Assessment And Risk Management Of Engineered Nanoparticles : Investigation In Semiconductor Wafer Processing, Michele Shepard

Legacy Theses & Dissertations (2009 - 2024)

Engineered nanomaterials (ENMs) are currently used in hundreds of commercial products and industrial processes, with more applications being investigated. Nanomaterials have unique properties that differ from bulk materials. While these properties may enable technological advancements, the potential risks of ENMs to people and the environment are not yet fully understood. Certain low solubility nanoparticles are more toxic than their bulk material, such that existing occupational exposure limits may not be sufficiently protective for workers. Risk assessments are currently challenging due to gaps in data on the numerous emerging materials and applications as well as method uncertainties and limitations.

Injury Prevention With Physical Therapy, Karen Kott, Margaret F. Lemaster

Rehabilitation Sciences Faculty Publications

(First paragraph) Ergonomics is the study of human performance (positioning and movement) and workplace design, such as equipment, ambience, and placement. The purpose of ergonomics is to maximize productivity by increasing safety, improving work quality, reducing operator fatigue and discomfort, and decreasing the risk of work -related musculoskeletal disorders (MSDs).^1-3

Adequate Ventilation: How Is It Defined And Does It Adequately Warn Consumers?, Christopher Blankenship

Theses, Dissertations and Capstones

The purpose of this research was to clarify and define the term “adequate ventilation.” Upon looking at regulations, court cases, and other elements, it is clear that the term is inadequate to inform consumers and does not instruct consumers on how to achieve proper ventilation. To find out if consumers understand this, random persons were asked to define it. The answers were given a numerical value to show the knowledge trend. The outcome showed that most people do not understand how to achieve proper ventilation. Conclusion: Diagrams showing how to set up a room with ventilation and new instructions are …

Assessment Of Neck And Shoulder Muscle Coactivations And The Effect On The Musculoskeletal System, Regina Derria Pope-Ford

Dissertations

Musculoskeletal disorders (MSDs) constitute one of the most important occupational health issues in healthcare workers who are susceptible to upper extremity disorders. Yet MSDs in the healthcare professions have not been studied extensively beyond the lower back. The focus population for this research is the field of dentistry where neck and shoulder disorders have been documented to have a high prevalence. Though quantitative data has been collected, many prior studies have focused on self-reported information. The goal of this research is to provide insight into the inter-relationship of muscles in the upper extremities. One way to accomplish this is to …

Quantifying The Ergonomic Impact On Healthcare Workers Using A Needle-Free Injector Device, Humberto Jose Olivero Lara

USF Tampa Graduate Theses and Dissertations

Background: Jet injectors are advantageous over needle injectors by eliminating sharps hazards. The Government Accountability Office estimates 29% preventable sharp injuries with an estimated direct cost of more than $500 million out of the CDC's reported incidence of 385,000 needle stick injuries per year among US hospital healthcare workers. Yet the forces required to set and trigger devices using spring mechanisms for medication delivery have not been explored. This laboratory experiment measured forces exerted by healthcare workers (HCWs) using a particular jet injector approved by FDA in 2011.

Objectives: In order to quantify the ergonomic impact on HCWs using a …

Characterization Of Graphite Composite Material Particulates From Usaf Aircraft Maintenance Operations, Richard E. Yon

Theses and Dissertations

Due to the benefits of their material properties, advanced composite materials (ACM) are increasingly being used as structural components on aircraft, especially within the United States Air Force. As a result, the potential exists for occupational exposures to structural maintenance employees while repairing and fabricating aircraft components. Two field studies were conducted for this thesis in order to characterize ACM aerosol size distribution, determine the feasibility of utilizing direct reading instruments (DRIs) in the field, and ensure workers are protected with adequate controls. In order to characterize exposure, traditional integrated air sampling and DRIs were positioned together near an ACM …

Retrospective Geospatial Modeling Of Pm10 Exposures From Open Burning At Joint Base Balad, Iraq, John P. Rinker

Theses and Dissertations

Predicting, determining, and linking theater-related source-specific exposures to health effects has proven difficult. The purpose of this research is to delineate retrospective exposure zones using spatially interpolated particulate air sampling point data from Joint Base Balad, create burn pit exposure isopleths from dispersion model outputs, and merge into a combined exposure model in GIS. Interpolated monitoring results and dispersion modeled results were combined to compare modeled exposures across base. Burn pit contribution to total PM10 was also modeled. The combined dispersion and interpolation map showed elevated concentrations within a 1 kilometer buffer of the burn pit. Buildings within this area …

Apparent Total Evaporative Resistance Values From Human Trials Over A Range Of Metabolic And Heat Stress Levels, Matthew David Dooris

USF Tampa Graduate Theses and Dissertations

Failure to maintain thermal equilibrium can cause uncontrollable increases in body core temperature beyond critical upper limits. In selecting clothing, consideration must be given to the heat transfer properties of clothing that may restrict the cooling capacity of the human body under heat stress conditions, most importantly, apparent total evaporative resistance (R_e,T,_a). This study calculated and compared R_e,T,_a for five clothing ensembles under varying heat stress conditions, including three relative humidity (RH) levels and three stages of heat stress to determine if R_e,T,_a values varied or remained the same with …