Nanotechnology Commons^™

Numerical Investigation Of Liquefaction Mitigation In-Sandy Soils Under Earthquake Loading Using Vertical Gravel Drains., Marawan M. Shahien M. Shahein, Ahmed Nasr, Baher Mohamed Abd El Fattah

Journal of Engineering Research

Liquefaction is one of the most dramatic defects of granular soil. This phenomenon is mostly observed when loose sand is subjected to a dynamic load or earthquake. In this study, the liquefaction that affected the loose soil evaluated, and some recommendations are introduced. (2-D) Numerical analysis using Plaxis (8.2) was conducted to simulate the behavior of the loose soil under dynamic loads. The studied model was carried out on multi-layers soil supported by stone columns subjected to dynamic loads. It was found that stone columns enhanced the soil behavior and reduced the damage that occurred. Liquefaction of the loose soil …

Chemical Kinetic Investigation: Exploring The Impact Of Various Concentrations Of Hho Gas With A 40% Biodiesel/Diesel Blend On Hcci Combustion, Mai H. Aboubakr, Medhat Elkelawy Prof. Dr, Eng., Hagar Alm-Eldin Bastawissi, Ayman Refat Abd Elbar

Journal of Engineering Research

This study uses the Chemkin software program to evaluate the effect of different quantities of oxyhydrogen gas [HHO] added to 40% biodiesel and diesel mix [B40], including B40, B40+5HHO, B40+10HHO, and B40+15HHO, on the HCCI combustion process's efficiency. The information collected includes cylinder pressure, cylinder temperature, accumulated gas phase heat release, heat loss rate, UHC, and mole fractions of O2, CO, CO2, diesel [NC7H16], biodiesel [C5H10O2], and oxyhydrogen [H2O]. The finding is that, when compared to a blend of biodiesel and diesel, using oxyhydrogen in the biodiesel/diesel mix boosts the properties of the HCCI engine.

Exploring The Influence Of Various Factors, Including Initial Temperatures, Equivalence Ratios, And Different Biodiesel/Diesel Blend Ratios, On Homogeneous Charge Compression Ignition (Hcci) Combustion, Mai H. Aboubakr, Medhat Elkelawy Prof. Dr, Eng., Hagar Alm-Eldin Bastawissi, Ayman Refat Abd Elbar

Journal of Engineering Research

This paper discusses the impact of three study cases that change with different values: the first case is four initial temperature values [313, 323, 333, and 343 K], the second case is three equivalence ratios [0.2, 0.3, and 0.4], and the third case uses various concentrations of biodiesel and diesel mixes [D100, B20, B40, B60, B80, and B100]. The purpose is to use the Chemkin software program to determine the effectiveness of each case in the HCCI combustion process. The results included cylinder pressure, cylinder temperature, accumulated gas phase heat release, heat loss rate, UHC, and mole fractions of O …

Survey And Analysis Of Safety Components And Costs In Construction Projects In Egypt, Emad E. Etman Prof., Haytham Sanad Prof., Asmaa Ibrahim Khater

Journal of Engineering Research

The difficulty of determining the factors that achieve safety on Egyptian construction sites as a result of multiple and different criteria and different relative weights of the criteria represents a challenge to achieve safety and a secure environment on construction sites. This issue has been of interest for many decades and continues to be a topic of discussion today because of construction project management is rapidly modernizing. The paper aims to identify the safety standards most commonly used on construction sites, and determine their relative weights as seen by the target audience and also estimate the cost of safety measures …

Enhancing Decision In Information System Through Weighted Preliminary Pretopology Analysis, Mustafa Elsayed, Rifet Agassi

Journal of Engineering Research

It is clear from adequate study of the past decades that there has been rapid growth in the information system, which relies mainly on programming systems. This has led to the necessity of dealing with high efficiency with the information system necessary for decision support. Information systems are a mixture of software and hardware to store and process all the data required and are presented in a useful form to extract information by applying topological concepts. In this paper a pretopological space from an information system is to be constructed. The computation of decision accuracy stands as a pivotal stage …

تحسين كفاءه التوازن الحرارى لمستخدمى الفراغات السكنيه, Alamera Kamal Elden Elfeky, Elamira Elfeky, Walaa Ahmed Nour, Lobna Abdallah Agha

Journal of Engineering Research

human belonging to nature Considered innate, and known as Biophilie, it has direct and strong relation with human heath and his welfare which affected by quality of internal environment where we Live and work as we spend most of our time in this environment. Biophelic design Aim to improve heath and welfare of human. natural. and reconnect him with his natural environment beside achieving the aesthetic aspect of his place.

in our present time, gap appeared in relation between human and environment as a result of modern design solution, as it has negative effect on human heath and safety, to …

Towards Environmentally Sustainable Preservation Of Heritage Buildings, Rozal Rozal Yousef Hanna1, Ayman Gamal El-Din Abd El- Tawab2, Walaa Abou El- Haggag Mehanna3

Journal of Engineering Research

The construction industry, characterized by its intricate processes and extensive stakeholder networks, stands at the cusp of a digital revolution. The adoption of blockchain-smart contract (BCSC) technology is at the heart of this transformation. This research delves deep into the BCSC within the construction arena to provide comprehensive insight into its probable applications, inherent challenges, and potential future trajectories. Leveraging the PRISMA analysis technique, a curated collection of relevant academic research articles was assembled, shedding light on the existing body of knowledge regarding the application of BCSC technology in construction. The authors developed an innovative user interface tool customized to …

Review: Protection Of Wooden Structures With Nano-Titanium Dioxide Coating, Zienab Zienab A. Ahmed1*, And M. M. Mosallem2

Journal of Engineering Research

Wood is widely used for various purposes with good performance. Wood works as the main material for furniture, monuments, decorations and constructions. which has the close relationship with human. Durability of wood is important in ensuring an appropriate life for the structure being designed. Wooden construction deteriorates easily due to UV radiation and weather conditions. Many of wood types need a preservative treatment. Several compounds are available for chemical protection, but not all are completely safe for human health. New technologies with low environmental impact and economically feasible are developed, which improves the life cycle of wood. Titanium dioxide is …

Urbanism Strategies For Linking Existing And New Cities, Naglaa J. Q. Mo’Men Abdel-Qader Ebrahim1, Mohsen Bayad2

Journal of Engineering Research

New cities, designed for urban growth outside existing metropolitan regions, face challenges in street infrastructure due to rapid expansion. Efficient control of mobility is crucial as cities grow. Sustainable transportation involves factors like infrastructure, public transit, delivery networks, affordability, efficiency, air quality, health, and reduced emissions. Commuting between established and new urban areas is common, leading to issues like urban sprawl, longer travel times, and congestion in developing countries. The challenge is to improve accessibility while addressing air quality, traffic, congestion, noise, built environment, emissions, and sprawl. This study aims to explore factors influencing mobility choices in Egypt, focusing on …

Manufacturing Of Aligned Electrospun Nanofiber Yarns For Their Enhanced Mechanical And Piezoelectric Properties, Adaugo Mary-Frances Enuka

Theses and Dissertations

Electrospinning is a widely used technique for producing nanofibers with diverse applications. This method uses polymer solutions and strong electric fields to generate nano-sized fibers with unique properties. This study presents a novel manufacturing approach that enables the production of electrospun poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) nanofiber yarns using an automated parallel track system and an adjustable roll-to-roll collector. This research examines the impact of an automated post-drawing system on the polymer chain orientation, crystallinity, tensile strength, morphology, and piezoelectric properties of PVDF-HFP nanofiber yarn. The results reveal that the post-drawing process significantly improves molecular alignment, increases tensile strength, and enhances the …

Building For Safety: Design Considerations For Refuge Areas In Tall Buildings From Quality Management Perspective, Enass. A. Salama, Heba. M. Gaber, Ahmed. M. Selim

Journal of Engineering Research

New El Alamein City is one of the largest urban projects in Egypt, and the largest project on the north coast. Tall buildings (super high-rise buildings) are considered the prevailing trend by architectural designers to obtain the maximum view of the Mediterranean Sea. The provision of safety evacuation in emergencies for these buildings’ occupants is a crucial challenge from the Quality management point of view. In contrast, there are no sufficient architectural design guidelines for the tall buildings provided by the Egyptian code for protecting buildings from fire, especially the design of the refuge areas. This study aims to investigate …

Effect Of Organic Compounds Additives For Biodiesel Fuel Blends On Diesel Engine Vibrations And Noise Characteristics, Medhat Elkelawy Prof. Dr, Eng., Hagar Alm-Eldin Bastawissi Prof. Dr. Eng., E. A. El Shenawy Prof. Dr., Mahmoud Soliman Eng.

Journal of Engineering Research

The extensive consumption of petroleum fuel directly correlates with both hazardous exhaust emissions affecting human health and contributing to global warming. Initially, biodiesel fuels were proposed as a viable alternative to address these issues. This perspective finds support in numerous published studies that highlight how the significant catalytic effect of nanoparticles allows for their integration into biodiesel blends, resulting in improved combustion characteristics, reduced exhaust emissions, and enhanced performance. This study investigates the impact of additives on biodiesel fuel properties and its effects on engine performance metrics such as brake power, brake thermal efficiency, exhaust gas concentration, engine vibration, and …

Investigation Into The Impact Of Ammonia Hydroxide On Performance And Emissions In Compression Ignition Engines Utilizing Diesel/Biodiesel Blends, Medhat Elkelawy Prof. Dr, Eng., Hagar Alm-Eldin Bastawissi, Mohammed Osama Elsamadony Dr. Eng., Abdallah Salem Abdalhadi

Journal of Engineering Research

In recent times, there has been a surge in scientific endeavors aimed at combating global warming. Various methods have been employed to address this issue, including the substitution of fossil fuels with more environmentally sustainable alternatives and the combination of different fuel types. This can be achieved through the integration of innovative injection systems and the simultaneous combustion of alternative fuels alongside fossil fuels, or by modifying fuel injection systems such as in the PCCI, RCCI, or HCCI systems. In a particular research investigation, a blend of ammonia hydroxide and diesel, with volume percentages of 7.5% and 92.5% respectively, was …

Enhancing Diesel Engine Performance By Directly Injecting Blends Of Ammonium Hydroxide And Including Liquid Petroleum Gas As A Partially Premixed Charge, Medhat Elkelawy Prof. Dr, Eng., Hagar Alm-Eldin Bastawissi, Mohammed Osama Elsamadony Dr. Eng., Abdallah Salem Abdalhadi

Journal of Engineering Research

Recently, scientists have made significant strides in addressing or mitigating environmental issues. Researchers have adopted various approaches to tackle these issues, such as replacing fossil fuels with more environmentally friendly alternatives or blending multiple fuel types. This can be achieved by either integrating these two trends through the use of new injection systems and simultaneous combustion of alternative fuels with fossil fuels or by modifying fuel injection systems, exemplified by the PCCI, RCCI, or HCCI systems. Consequently, these methods have proven effective in reducing environmental pollutants, enhancing thermal efficiency, and decreasing specific fuel consumption. In this study, ammonia hydroxide and …

Experimental Investigation On Combustion And Emission Characteristics Of Co-Combustion Of Pulverized Biomass With Diesel Fuel In An Industrial Burner, Medhat Elkelawy Prof. Dr, Eng., Hagar Alm-Eldin Bastawissi, Ahmed Abou El-Yazied Prof. Dr., Saad El-Malla Dr. Eng.

Journal of Engineering Research

This study presents the combustion and emission results obtained from a laboratory furnace equipped with a 35 kW industrial burner that utilizes co-combustion of pulverized biomass and diesel fuel. The experiment compared the co-combustion of pulverized biomass and diesel fuel with diesel fuel alone. Three different loading ratios of pulverized biomass from residual beet samples were used. Temperatures were measured at various positions inside the furnace to analyze combustion performance. It was observed that increasing the biomass loading ratios led to higher flame temperatures and improved combustion compared to diesel fuel alone. The concentrations of pollutants such as Co, HC, …

Cfd Study On Two-Phase Flow Patterns In A Pipe With 90º Elbow In Different Operating Conditions, Hagar Alm-Eldin Bastawissi, Mohammed Ahmed Khafagy, E. A. El Shenawy Prof. Dr., Ahmed M. Salem Dr

Journal of Engineering Research

Recently, CFD has offered a technological solution for modelling multi-phase flow in which we can make endless simulations with reduced expenses and effort in high accuracy results; we shall also mention that experimental studies have limitations for safety considerations when experimenting with flow in high temperature or pressure values or medium nature as in nuclear or chemical flows.In this paper, we used the ANSYS FLUENT CFD program to simulate the two-phase flow in a pipe to study the effect of attaching a 90-degree elbow fitting to the piping system, seeking to find out the change in the pattern and resulting …

تقنيات الاضاءة الصناعية وتأثيرها فى الفراغ السكنى على السلوك الانسانى, Samah Kamal Elfeky, Walaa Ahmad Nour, Lobna Abdelfatah Agha

Journal of Engineering Research

* Lighting is considered of main items in daily life begining from natural Lighting to industrial lighting. with all of it's different shapes . it is considerdone of the most important data that point Blank spaces and works to show architectural spaces, aesthetic values through being sharp and weak, ensure borders show texture or hide Features, suggest wideness, narrowness of space as the most beautiful design don't see beautiful without good lighting which designed carefully.Due to diversity of human activities, architictums spaces and it is wideness. Increased dependence on industrial Lighting to strengthen Job of performance, beauty of internal, external …

Nanoparticles For Applications In Specific Diagnostics And Precision Medicine, Naxhije Berisha

Dissertations, Theses, and Capstone Projects

Heterogeneity is common in the expression of cancer and treatment response. Precision medicine enables healthcare providers to tailor medical care to an individual's distinct genetic and environmental makeup. This customization has the potential to result in more efficient treatments while minimizing side effects. We believe that by studying the interface of nanotechnology and cancer medicine we can elucidate innovative solutions that address the challenges of disease heterogeneity. This includes advancements in drug delivery, formulations development, and diagnostic sensing. We highlight three studies that use nanotechnology for applications in precision medicine. In Chapter 2, we highlight design optimization of drug formulations …

The Influence Of Green Building Design On Tourists' Intention To Stay In Eco-Friendly Hotels: A Study On Perceptions And Preferences, Enas Al Sayed Salama Dr., Gehad Nasr Abdelsalam Dr.

Journal of Engineering Research

Green building design involves integrating sustainable and environmentally friendly practices into the construction and operation of buildings, including hotels, with the goal of minimizing the adverse impact on the environment. This paper delves into the pivotal role of green building design and eco-service provision within the context of green hotels. The aim is to investigate the interconnections among tourists' environmental concerns, their perceived significance of green building design, and their intention to choose green hotels.

To enhance the understanding of tourist behavior and its implications for tourism in Egypt, a questionnaire was administered in Sharm El Sheikh, a prominent Egyptian …

Experimental Study Of Bent Glass Curtain Walls., Sarah Said Abd El Kariem, Moustafa El Shami, Mahmoud El Nagar

Journal of Engineering Research

A Bent Laminated Glass is commonly used in the residential and commercial structures, its methodology is not present in the curves and tables at the ASTM E1300. Therefore, it has become a need for architects to use basis for this type of glass. To the best of authors ‘knowledge, no one study the bent laminated glass in details. A variety of safety glass that has lately gained popularity in the construction sector is modern laminated glass. Given that it offers a safe failover capability, it is perfect for the automotive industry. Double-lite glass is produced using two or more …

Market Analysis And Bidding Strategy Of Hybrid Renewable Energy Systems Considering Emissions, Fatma Elzahraa, Mohamed Elnemr, Samir Dawoud

Journal of Engineering Research

The competition in the electricity markets makes it difficult to choose a suitable strategy for maximizing profit while reducing harmful emissions. To have an adequate energy price for consumers while minimizing the harmful emissions to the atmosphere and maximizing profits of all participants in the electricity market needs an aggressive bidding strategy. Developing these bidding strategies with the integration of renewable energy (RE) in the electricity market became important. This research studies various bidding strategies for maximizing profits in the deregulated energy market since participants are keen on developing bidding strategies considering emissions. These bidding strategies will consider the integration …

Effects Of Fuel Equivalence Ratio And Swirl Vane Angles On Premixed Burner Turbulent Flame Combustion Characteristics, Medhat Elkelawy Prof. Dr. Eng., E. A. El Shenawy Prof. Dr., Hagar Alm-Eldin Bastawissi Prof. Dr. Eng., Ibrahim Ali Mousa Eng., Mohamed M. Abdel-Raouf Ibrahim Dr. Eng.

Journal of Engineering Research

A turbulent flow field has a major effect on the premixed flame structure and temperature distribution that specifically determines the effectiveness of the burned fuel and the amounts of produced emissions. However, the premixed flame tangential and axial velocity distribution through the flame length help to predict the combustion and emissions attributes of the burned fuel. In this regard, an experimental and analytical investigation on premixed turbulent burners at different equivalence fuel-air ratios with different swirl vane angles has been achieved in the present work to assess the combustion performance and emissions characteristics. A theoretical methodology was carried out to …

Enhancing The Performance Of Conventional Solar Still Using The Nano-Doped Paint (Ndp) Coating, Hagar Alm-Eldin Bastawissi Prof.Dr, Nermin Elgendy Engineer, Ayman R. El-Tohamy

Journal of Engineering Research

Nations are throughout the entire globe continuously confronting the problem of potable water shortage. Recently, it has been thought that using solar energy to desalinate brackish water offers a practical answer to the world's water crises. The output of these stills, is meager, and academics haven't done much to boost it in any way. Solar distillers have been proposed as an efficient method to produce potable water. In recent years, saltwater has produced drinking water by various ways. The efficiency of a solar distiller is significantly influenced by various factors, most important factor of them is the absorber surface. In …

Engine Performance And Emissions Improvement Study On Direct Injection Of Diesel/Ammonia Dual Fuel By Adding Cng As Partially Premixed Charge, Medhat Elkelawy Prof. Dr, Eng., Hagar Alm-Eldin Bastawissi Prof. Dr., Mohammed Osama Elsamadony Dr. Eng., Abdallah Salem Abdalhadi Eng.

Journal of Engineering Research

Researchers have recently moved on in their studies to find a solution to prevent or reduce this problem. There have been directions taken by researchers to solve the problem, including, replacing fossil fuels with environmentally friendly types or by combining two or more types of fuel. This is by modifying fuel injection systems as appears in the PCCI, RCCI, or HCCI systems, or working to integrate the two trends by using new injection systems and burning alternative fuels with fossil fuels. Therefore, the trend has good results on the specific consumption of fuel, raising thermal efficiency, and working to reduce …

Experimental Study On The Impact Of Secondary Air Injection And Different Swirl Van Angles On Premixed Turbulent Flame Propagation And Emission Behaviors, Medhat Elkelawy Prof. Dr. Eng., E. A. El Shenawy Prof. Dr., Hagar Alm-Eldin Bastawissi Prof. Dr. Eng., Ibrahim Ali Mousa Eng., Mohamed M. Abdel-Raouf Ibrahim Dr. Eng.

Journal of Engineering Research

The objective of the present paper is to investigate experimentally the flame characteristics utilizing different secondary air inlet direction for different primary air swirl numbers and equivalence fuel-air ratios. In this study, an experimental test rig was carried out to investigate the flame temperature and emission behavior with flame length at the equivalence fuel-air ratios taken0.96, 0.80, 0.70, and 0.60, and swirl vane angles were varied as 20, 30, 45, and 60° to generate different swirl numbers of 0.26, 0.416, 0.71 and 1.23, respectively. In addition to the introduction of secondary air in test combustor, whereas the primary air and …

The Effect Of An Existing Tunnel And A Newly Excavated Tunnel On Ground Loss Beneath Sand Slope-3d Numerical Study, Ashraf Nazir, Ahmed Nasr, Asmaa Saeed

Journal of Engineering Research

Abstract- Most researchers perform their numerical models for tunnels by modeling perfectly horizontal ground surfaces above the tunnels. The prediction of surface settlement of a sandy slope due to the interaction mechanism between the slope and the tunnels is one of the critical problems in urban areas. As a result, in this work, a numerical analysis using PLAXIS 3D TUNNEL has been performed to investigate the effect of tunnel excavation on the deformation of a shallow sandy slope, and empirically by the Herzog method. The study also assesses the influence of parameters on slope deformation that have not been …

Development Of Iron Oxide Nanozyme For Cancer Therapy, Zhongchao Yi

Theses and Dissertations--Biomedical Engineering

Cancer therapies that leverage reactive oxygen species (ROS) have shown potential for cancer inhibition due to their ability to induce oxidative stress in tumor cells. Iron oxide nanoparticles (IONPs) have garnered significant attention as a promising platform for ROS-dependent disease treatment, owing to their remarkable biocompatibility and Fenton catalytic activity. However, the low catalytic activity of IONPs has been a major hurdle in their clinical translation. To overcome this challenge, IONPs of different compositions are examined for their Fenton reaction under pharmacologically relevant conditions in this work. The results show that wüstite (Fe_1-xO) nanoparticles exhibit higher catalytic activity …

Photoluminescence Switching In Quantum Dots Connected With Carboxylic Acid And Thiocarboxylic Acid End-Group Diarylethene Molecules, Ephraiem S. Sarabamoun, Pramod Aryal, Jonathan M. Bietsch, Maurice Curran, Sugandha Verma, Grayson Johnson, Lucy U. Yoon, Amelia G. Reid, Esther H. R. Tsai, Charles W. Machan, Christopher Paolucci, Guijun Wang, Joshua J. Choi

Chemistry & Biochemistry Faculty Publications

We contrast the switching of photoluminescence (PL) of PbS quantum dots (QDs) cross-linked with photochromic diarylethene molecules with different end groups, 4,4′-(1-cyclopentene-1,2-diyl)bis[5-methyl-2-thiophenecarboxylic acid] (1C) and 4,4′-(1-cyclopentene-1,2-diyl)bis[5-methyl-2-thiophenethiocarboxylic acid] (2T). Our results show that the QDs cross-linked with the carboxylic acid end group molecules (1C) exhibit a greater amount of switching in photoluminescence intensity compared to QDs cross-linked with the thiocarboxylic acid end group (2T). We also demonstrate that regardless of the molecule used, greater switching amounts are observed for smaller quantum dots. Varying these parameters allows for the fabrication of photoswitches with tunable PL change. We relate these observations to the …

Compton Scattering Of Mammographic Soft X-Ray Beams By Alkali And Transition Metal Salt Filters Produce X-Ray Interference Zones That May Have Treatment Potential For Localized Cancer Lesions, Subhendra N. Sarkar, Eric Lobel, Sabina Rakhmatova, Derbie Desir, Somdat Kissoon, Daler Djuraev, Katie Tam

Publications and Research

In breast x-ray imaging scattered radiation adds 50% of harmful radiation dose from anisotropic Compton scattering mechanism. We have been working with double layered inorganic salt materials that can induce Compton scattering to the incident mammographic x ray beams (in 20-30 kVp range) with adequate isotropy (angular control). Typically metal nitrates and alkali halide salt layers are shown here to cause low energy radiation interference zones with high and low photon intensities and local flux heterogeneity in terms of flux covariance. Spatial variation of low energy photon flux creates concentrated and sparse radiation zones that may be used to induce …

Levofloxacin Incorporated Extracellular Matrix Nanoparticles For Pulmonary Cystic Fibrosis Infections, Raahi Patel

Theses and Dissertations

Cystic fibrosis (CF) is a progressive genetic disorder that affects around 40,000 people in the United States. CF is characterized by a mutation in the CFTR protein that causes dysregulated ion transport across epithelial cells, producing viscous mucus in the lung that increases bacterial invasion, causing persistent infections and subsequent inflammation. Pseudomonas aeruginosa and Staphylococcus aureus are two of the most common infections in CF patients that are resistant to antibiotics. One antibiotic approved to treat these infections is levofloxacin (LVX) that functions to inhibit bacterial replication, but can be further developed into tailorable particles. Nanoparticles are an emerging inhaled …