Prosthodontics and Prosthodontology Commons^™

Evaluation Of Finger-Tightening Torque Applied To Implant Healing Abutments By Dental Providers With Varying Experience And Physical Characteristics: An In-Vitro Study., Bayan Abuhalimeh

Graduate Theses, Dissertations, and Problem Reports (ETD)

Aim: The primary objective of this project is to measure the actual torque applied by dental providers when finger-tightening a healing abutment and assess the variability among individuals. A secondary objective is to analyze the correlation between applied torque and: provider experience level (residents, general dentist, specialist); gender; age; and, physical attributes (e.g., grip strength, hand size, and dominant hand used for tightening). The null hypothesis is that there is no difference in the mean finger-tightening among the three groups of dental providers, and there are no significant differences in torque values among practitioners based on demographic and professional variables. …

Comparative Evaluation Of Bending Resistance And Retentive Torque Stability Of Zest Locator® And Straumann Novaloc® Abutments: An In Vitro Study, Hammad Ul Haq

Graduate Theses, Dissertations, and Problem Reports (ETD)

Abstract

Comparative Evaluation of Bending Resistance and Retentive Torque Stability of Zest Locator® and Straumann Novaloc® Abutments: An In Vitro Study

Hammad Ul Haq B.D.S.

Objective: To compare the mechanical performance of Locator® (Zest Anchors) and Novaloc® (Straumann) implant overdenture attachment systems connected to Straumann Bone Level Conical (BLC) implants under standardized cyclic and static off-axis loading conditions.

Materials and Methods: Ten Straumann BLC implants were divided into two groups (n = 5): Group 1 received Locator® abutments and Group 2 received Novaloc® abutments. All abutments were tightened to 35 N·cm and retightened after 10 minutes. Baseline removal torque values …

Implant Overdenture Abutment Loosening Under Hyperbaric Conditions, Zana Jamal Al-Saloum

Graduate Theses, Dissertations, and Problem Reports (ETD)

Objectives: To investigate the effect of various hyperbaric air pressures on the loosening of LOCATOR® (ZEST Anchors, LLC, Escondido, CA USA) overdenture abutments.

The pressure conditions tested are meant to simulate scuba diving conditions in edentulous patients that are restored with implant-retained tissue-supported overdentures. Another sub-goal of this study is to determine whether or not there is a difference in LOCATOR® loosening when the sample is exposed to six cycles/dives as opposed to one cycle/dive.

Methods: 36 ZimVie Tapered Screw Vent Implants with a 3.5mm diameter implant platform, and a 2.5mm diameter (and 1.5mm deep) internal hexagon were …

Accuracy Of Implant Placement Utilizing Stereolithographic Guides Printed With And Without Cross-Arch Stabilization Struts, Caitlin Libby Dds

Graduate Theses, Dissertations, and Problem Reports (ETD)

Objectives: The purpose of this study was to assess the accuracy of implant placement using stereolithographic guides printed with and without stabilization struts by comparing the post-operative position to the planned implant position.

Methods: A pre-operative cone-beam computed tomography (CBCT) of a drillable maxillary model was obtained and data was uploaded into coDiagnostiX for preoperative planning. The implant position was planned in an edentulous space of #5 using a 3.3x10mm Bone Level Tapered (BLT) implant (Straumann). Ten surgical guides were designed utilizing a stabilization strut (Group A), while ten guides were designed without the stabilization strut (Group B). Twenty guides …

Accuracy Of Digital Impressions At Varying Implant Depths: An In-Vitro Study, Vivia Sequeira

Graduate Theses, Dissertations, and Problem Reports (ETD)

Introduction: Implants placed at variable depths may vary the amount of visible scannable surface of a scan body. Intraoral scanner technology uses advanced optical principles to record the surface of the scan body to accurately capture the implant position.

Purpose: To investigate the effect implant placement depth has on the accuracy of digital implant impressions using an intraoral scanner.

Materials & Methods: A partially edentulous gypsum master model was fabricated to allow the positioning of a single implant analog at different depths. Four groups based on the planned implant depths of 0, 3, 6 and 7mm and corresponding visibility of …

Accuracy Of Blx And Blt Guided Implants In The Edentulous Maxilla: An In Vivo Study, Benjamin Andrew Kordusky

Graduate Theses, Dissertations, and Problem Reports (ETD)

Objectives: To determine the accuracy of dental implants placed using a dual scan CBCT protocol with a SLA 3D printed mucosa supported surgical guide using a flapless surgical approach with regard to sleeve position, type of implant, and regional location in the maxillary arch.

Methods: Nine patients received 4 dental implants utilizing a fully guided, flapless approach with a mucosa supported SLA surgical guide with 3 fixation pins. Implants were immediately loaded using an attachment placed in an existing Maxillary complete denture. Accuracy of implant positions were evaluated by the Treatment Evaluation module of coDiagnostiX (DentalWings, Montreal, Canada). Statistical analysis …

The Visual And Spectrophotometric Effect Of External Bleaching On Omnichroma Resin Composite And Natural Teeth, Michael Brian Evans

Graduate Theses, Dissertations, and Problem Reports (ETD)

Objective: To determine the visual and spectrophotometric effect external tooth bleaching has on natural tooth structure and OMNiCHROMA composite at various number of treatments. Variables were compared to determine if there is a detectable difference between the composite and the tooth before and after bleaching.

Methods: Preparation and restoration of 25 previously extracted teeth was completed. OMNiCHROMA composite was used. Each tooth was measured visually with a VITA shade guide and a colorimeter. Measurements were recorded before bleaching, after 5 and 10 treatments. Statistical analysis was completed and ΔE values between the composite and tooth were compared between the 3 …

The Effect Of Occlusal Pressure On Vertical Force Generation On Dentate And Edentulous Subjects, Matthew Thomas Harper

Graduate Theses, Dissertations, and Problem Reports (ETD)

Objectives: To determine 1) the difference in lower extremity power obtained from a vertical jump in individuals who are dentate or edentulous (implants or dentures) and 2) the difference occlusal pressure makes on lower body force output. Variables included jump height, maximum kicking force, maximum push off force, take off velocity, flight time, jump impulse, and maximum velocity. Groups included dentate, implant overdenture, and conventional denture.

Methods: Counter movement jumping with force plate collection was utilized to test the three populations in this study. The three populations were dentate, mandibular implant overdenture opposing maxillary complete denture, and conventional maxillary and …