Oral and Maxillofacial Surgery Commons^™

Pterygoid Implant-Retained Bridge Following Multiple Failed Alveolar Implants In Posterior Maxilla, Kouder Dakhallah Dds, Anish Gupta Dds, Joey Wilmot, Brian Giammalva Dds

The Journal of the Michigan Dental Association

The replacement of multiple teeth with dental implants in the posterior maxilla is challenging due to factors including low density bone and sinus morphology. When considering restoration of this region, prosthetic design will dictate implant placement. Additionally, planning must consider spacing between adjacent implants, spacing between implants and adjacent teeth, and irregular alveolar ridge morphology. These key measurements translate to the final prosthesis design and will affect cleanability and future oral hygiene maintenance. These characteristics subsequently affect overall longevity of the implants and prosthesis.

In the following case, multiple closely-placed implants presenting with poor cleanability consequently failed, requiring removal and …

Fabrication Of Implant Supported Hybrid Denture Using Multi-Unit Abutments In A Patient With Generalised Aggressive Periodontitis, Anupama Aradya, Raghavendra Swamy K N, Chandan S N, Prashanth M B

International Journal of Health and Allied Sciences

This case report describes the prosthodontic rehabilitation of a geriatric patient with generalized aggressive periodontitis. The patient was advised to for full extraction. An implant supported hybrid prosthesis with multi-unit abutments was fabricated for the patient who chose a fixed kind of prosthesis. Implants were placed in the maxillary & mandibular arch. Frameworks were waxed, plastic castable abutments were used for casting, denture teeth were waxed to the hybrid framework and a final wax try-in to check and adjust the maxilla-mandibular relationships before processing, the prosthesis was placed. The clinical and radiologic results met expectations.

Peri-Implantitis Incidence And Effect Of Supportive Periodontal Therapy On Outcomes: Retrospective Cohort Study, Michael Ha

Theses and Dissertations

Purpose: Management of peri-implantitis is becoming an increasing component of dental practice. Dental implants can develop peri-implantitis lesions which occur in a non‐linear and accelerating pattern compared to a gradual periodontitis lesion. It is crucial to diagnose and treat this disease early, or ideally prevent it. Contemporary implants have a rough surface texture which is difficult to properly decontaminate as a crucial component for treatment prognosis. Evidence on the long-term effects of Periodontal implant maintenance therapy (PIMT) on implants is limited. This study aims to investigate the effect of periodontal maintenance on peri-implant tissue health.

Methods: A retrospective chart review …

Stress Analysis Comparing Effect Of Two Different Cad-Cam Implant Superstructure Materials (In-Vitro Study), Noura Turky Saad, Essam Osman, Ahmed M. Abdelhamid, Mohamed Shokry, Ehab A. Farghaly

BAU Journal - Creative Sustainable Development

Purpose: This study was conducted to evaluate the micro-strain around dental implant using two different CAD/CAM crown fabricated materials through strain gauge analysis. Materials and Methods: Five dental implants were fixed in a 5 previously drilled solid rigid polyurethane test blocks in the edentulous area with neighboring abutments mesial and distal printed out using special 3D Dental printer, Cyanoacrylate adhesive was then used to fix the printed-out part on to the polyurethane test blocks, creating the bounded saddle replicas. Ten CAD/CAM screw retained crowns were fabricated; five Enamic crowns from vita enamic blocks, and five zirconia crowns from presintered katana …

The Impact Of Impression Coping Geometrical Design On Accuracy Of Implant Impressions: An Experimental Study, Motaz Osman Osman, Neamat Hassan Abubakr, Ahmed Suliman, Hassan Ziada

Dental Medicine Faculty Research

Aim This in vitro study aimed to evaluate the effect of implant impression coping geometrical designs on the accuracy of open and closed impression techniques and in the parallel and nonparallel implant positions. Material and methods Three custom-made acrylic resin models of three tested implant systems (Straumann (R), SIC Invent (R), and Osstem (R)) with diverse coping geometrical designs were evaluated in simulated cases of two parallel and two nonparallel implants. The horizontal and vertical discrepancies were measured and analyzed. Results No statistically significant differences between the two impression techniques in either parallel or nonparallel implants were observed. The high …