Dental Materials Commons^™

Effects Of Different Denture Cleansers On The Tensile Bond Strength Of Denture Liners, Selda Keskin

The effect of two denture cleansers (Polident1 and Protefix1) on the tensile bond strength between four soft liner materials (Molloplast B1, Permaflex1, Sofreliner Tough Medium1, and GC Reline Soft1) and a conventional denture base resin was investigated. For each of the liner materials 35 test specimens were prepared according to test the requirements and assigned into seven groups (n¼5). Before tensile testing, five of the liner specimens were kept in water or soaked in two cleansing solutions during 2 and 7 d. Five other samples served as a control group subjected directly to tensile testing. The bond strength values were …

Tensile Bond Strength Of A Highly Cross-Linked Denture Tooth To The, Selda Keskin

This study compared tensile bond strengths between conventional compressionmolded heat (HC)-, auto (AP)-, and microwave-polymerized (MC) poly(methyl methacrylate)-based denture resins and a relatively new injection-molded, microwave-polymerized polyurethane based resin (MI) bonded to a highly cross-linked denture tooth. In the first part of the experiments, denture teeth were used as received. In the second part, they were treated with dichloromethane to see its effect on bonding of conventional denture bases (HCS and APS). Bond strength was tested in tension according to ADA specification No.15. The results showed that the HC group failed cohesively because of higher interface bonding (49.95 MPa) compared …

A Finite Element Study Of The Multilayered Structured Dental Post, Noor Hayaty Abu Kasim Abu Kasim N.H.

Noor Hayaty Abu Kasim Abu Kasim N.H.

Ideally, dental post should have stiffness that is similar to the crown at the coronal part and stiffness similar to the dentine at the apical part. This will reduce stress concentration at either coronal or the apical parts of the dentine and minimize the chance of interfacial loosening and enhance the reliability of post. Objective: To investigate the biomechanical behaviour of Multilayered Structured Dental Posts (MSDPs) using finite element analysis (FEA). Methods: Two models of MSDPs consist of multilayer design of xTi-yHA composition added to a zirconia layer (model A) and the same compositions added to alumina layer (model B) …

Influence Of Stainless Steel Orthodontic Brackets On Magnetic Resonance Imaging, Christian James Hoybjerg

Loma Linda University Electronic Theses, Dissertations & Projects

Introduction: Magnetic resonance imaging (MRI) machines provide 2D as well as 3D images that are excellent in contrasting soft-tissue in the maxillofacial region and are void of ionizing radiation. The drawbacks include the lack of depiction of cortical bony detail and image degradation caused by substances in the scanned area. Specifically, in the orthodontic field stainless steel brackets cause more distortion of MR images then any other bracket material. It is unknown what type of stainless steel alloy causes the most MRI distortion. The purpose of this study is to evaluate the degree of craniofacial MR distortion caused by various …

The Influence Of Work Of Fracture On Six Orthodontic Bonding Systems, Tyler S. Pritchard

Loma Linda University Electronic Theses, Dissertations & Projects

Introduction: Bonding is the primary method of attaching brackets to teeth in modem orthodontics. Thus, many studies have focused on the maximum shear bond strength values of orthodontic adhesives. In contrast, very little research has been performed considering the work of fracture of orthodontic bonding systems. Work of Fracture is defined as the area under the curve of a stress-strain graph. Previous shear bond strength studies measured the force necessary to produce bond failure. The purpose of this study was to measure the maximum shear force and displacement of six bonding systems and to calculate the work of fracture.

Materials …

Effect Of Auxiliary Preparation Elements On Resistance Form Of Complete Crowns, Manuel H. Guevara

Loma Linda University Electronic Theses, Dissertations & Projects

This study compared the effectiveness of six different auxiliary preparation elements on the resistance to lateral dislodgment of complete crown preparation lacking resistance form.

An ivorine mandibular first molar was prepared with the following characteristics: 20° TOC, 360° shoulder finish line of 1.0 mm width and axial wall of reduced height offering no geometric resistance form (Group A: control). Preparation modifications were Group B: MD grooves, Group C: BL groves (sic), Group D: MDBL grooves, Group E: MD small boxes, Group F: MD large boxes and Group G: 8° TOC at the cervical 2 mm of the axial walls. Ten …

The Effect Of Auxiliary Preparation Elements On The Resistance Form Of Complete Metal Crowns, Mostafa Nazari

Loma Linda University Electronic Theses, Dissertations & Projects

This study measured the resistance to dislodgment of complete metal crowns when they were fabricated for tooth preparations lacking resistance form. These preparations were modified with four different auxiliary preparation features.

An Ivorine mandibular first molar was prepared on a milling machine with the following characteristics: 20 degrees of total occlusal convergence (TOC), 360 degrees shoulder finish line of 1.0 mm width, and axial wall of reduced height offering no geometric resistance form. The following tooth preparation modifications were studied:

1. Two proximal grooves (two lingually positioned grooves, one on the mesial and one on the distal surface) (design B) (Figures …

Immediate Loading Of Unsplinted Implants In The Anterior Mandible For Overdentures, Phillip Roe

Loma Linda University Electronic Theses, Dissertations & Projects

In this one-year prospective study, eight completely edentulous patients were selected from the Loma Linda University School of Dentistry (LLUSD) patient population to participate. There were five male and three female patients, between the ages of 58 and 82 (mean age of 69.1 years). All participants received new maxillary and mandibular complete dentures prior to implant placement. Two 4.0 mm x 13 mm threaded implants with a fluoride-modified, micro-roughened, titanium surface were placed mesial to each mandibular canine position. Locator abutments were connected and torqued to 25 Ncm and primary closure was achieved with a nonresorbable suture material. The Locator …

A Finite Element Study Of The Multilayered Structured Dental Post, Ahmed A. Madfa

Ahmed A. Madfa

Ideally, dental post should have stiffness that is similar to the crown at the coronal part and stiffness similar to the dentine at the apical part. This will reduce stress concentration at either coronal or the apical parts of the dentine and minimize the chance of interfacial loosening and enhance the reliability of post. Objective: To investigate the biomechanical behaviour of Multilayered Structured Dental Posts (MSDPs) using finite element analysis (FEA). Methods: Two models of MSDPs consist of multilayer design of xTi-yHA composition added to a zirconia layer (model A) and the same compositions added to alumina layer (model B) …

Effect Of Filler Incorporation On The Fracture Toughness Properties Of Denture Base Poly(Methyl Methacrylate), Nidal Elshereksi

Nidal Elshereksi

Poly(methyl methacrylate) (PMMA) is the material of choice for denture base construction. In spite of its many good qualities, the application of PMMA as an ideal dental base material is still restricted by a few limitations. One of these is the difficulty in achieving intrinsic radiopacity in the material. The aim of the present study is to investigate the possibility of using barium titanate (BaTiO3) as a radiopacifier in PMMA. The formulation used in this study composed of PMMA 89.5 wt%, BaTiO3 10 wt% and benzoyl peroxide (BPO) 0.5 wt% as an initiator, methyl methacrylate (MMA) 90 wt% as a …

Effect Of Filler Incorporation On The Fracture Toughness Properties Of Denture Base Poly(Methyl Methacrylate), Nidal Elshereksi

Nidal Elshereksi

Poly(methyl methacrylate) (PMMA) is the material of choice for denture base construction. In spite of its many good qualities, the application of PMMA as an ideal dental base material is still restricted by a few limitations. One of these is the difficulty in achieving intrinsic radiopacity in the material. The aim of the present study is to investigate the possibility of using barium titanate (BaTiO3) as a radiopacifier in PMMA. The formulation used in this study composed of PMMA 89.5 wt%, BaTiO3 10 wt% and benzoyl peroxide (BPO) 0.5 wt% as an initiator, methyl methacrylate (MMA) 90 wt% as a …

The Current Status Of The Case Report: Terminal Or Viable, Noor Hayaty Abu Kasim Abu Kasim N.H.

Noor Hayaty Abu Kasim Abu Kasim N.H.

The case report, which has a long history in medicine, has seen its fortune wax and wane with time. We discuss the challenges facing the continued survival of the case report, including the inability of journals to cope with the increased load and increased cost of publication, ethical issues, the impact factor and the rise of evidence-based medicine. We highlight the important role that the case report will continue to play in medical research and education, as a means of sharing information and detecting novelty through observations. Most importantly, the case report serves as a stepping stone for young physicians …