Operations Research, Systems Engineering and Industrial Engineering Commons^™

Deep Learning Object-Based Detection Of Manufacturing Defects In X-Ray Inspection Imaging, Juan C. Parducci

Mechanical & Aerospace Engineering Theses & Dissertations

Current analysis of manufacturing defects in the production of rims and tires via x-ray inspection at an industry partner’s manufacturing plant requires that a quality control specialist visually inspect radiographic images for defects of varying sizes. For each sample, twelve radiographs are taken within 35 seconds. Some defects are very small in size and difficult to see (e.g., pinholes) whereas others are large and easily identifiable. Implementing this quality control practice across all products in its human-effort driven state is not feasible given the time constraint present for analysis.

This study aims to identify and develop an object detector capable …

Parametric Study Of Residual Stresses In Wire And Arc Additive Manufactured Parts, Hisham Khaled Jamil Abusalma

Mechanical & Aerospace Engineering Theses & Dissertations

Wire and Arc Additive Manufacturing (WAAM) is a cost-effective additive manufacturing process due to its capability to fabricate large metal parts with high deposition rate and low equipment cost. Although this method is gaining popularity in manufacturing industry, more research is needed to understand process parameters’ effects on residual stress (RS) distribution and part distortion. As such, a 3D thermo-elastic-plastic transient model was established in ABAQUS and employed to investigate the effect of process parameters such as the torch speed, the deposition power and the interlayer dwell time on RS distribution and distortion in WAAM part. The numerical model utilized …

Development Of A Dsm-Based Model For Managing The Design Of Complex Systems Considering The Impact Of Technological Obsolescence, Gershom Kwaku Obeng

Mechanical & Aerospace Engineering Theses & Dissertations

Obsolescence has been a constant issue for process planners and designers and if not properly accounted for, obsolescence can become an expensive issue. As systems become more complex, interconnected, and nonhomogeneous, separate studies of single groups of equipment are no longer sufficient in modeling the obsolescence of the systems that they make up. The purpose of this dissertation is to model the likelihood of a process's design becoming obsolescent given the obsolescent behavior of the equipment used to complete the process. The methodology discussed in this work is based on a combination of using a systems engineering tool called the …

A Unified Enterprise-Wide Cost Modeling Framework For Engineering Applications Based On Systems Engineering Principles, Yousuf S. Mohammed

Mechanical & Aerospace Engineering Theses & Dissertations

In the present research the problem of enterprise-wide cost modeling is approached from a systems engineering standpoint. What this does is to use each stage of product life cycle to obtain useful information that helps in estimating the cost of the system. Once a generic framework is developed for estimating the core cost, layers of other factors that affect the cost are applied to the core cost, such as risk and uncertainty, maintainability, supply-chain and socioeconomic conditions. The cost model is expanded to accommodate a product domain ranging from a simple object to a system in the following hierarchy: System, …

Modeling Multilevel Supply Chain Systems To Optimize Order Quantities And Order Points Through Mathematical Models, Discrete Event Simulation And Physical Simulations, Alok K. Verma

Mechanical & Aerospace Engineering Theses & Dissertations

Managing supply chains in today's distributed manufacturing environment has become more complex. To remain competitive in today's global marketplace, organizations must streamline their supply chains. The practice of coordinating the design, procurement, flow of goods, services, information and finances, from raw material flows to parts supplier to manufacturer to distributor to retailer and finally to consumer requires synchronized planning and execution. Efficient and effective supply chain management assists an organization in getting the right goods and services to the place needed at the right time, in the proper quantity and at acceptable cost. Managing this process involves developing and overseeing …

Optimization-Based Architecture For Managing Complex Integrated Product Development Projects, Hisham Mohamed El-Sayed Abdelsalam

Mechanical & Aerospace Engineering Theses & Dissertations

By the mid-1990's, the importance of early introduction of new products to both market share and profitability became fully understood. Thus, reducing product time-to-market became an essential requirement for continuous competition. Integrated Product Development (IPD) is a holistic approach that helps to overcome problems that arise in a complex product development project. IPD emphasis is to provide a framework for an effective planning and managing of engineering projects. Coupled with the fact that about 70% of the life cycle cost of a product is committed at early design phases, the motivation for developing and implementing more effective methodologies for managing …

Generic Cost Estimation Framework For Design And Manufacturing Evaluation, Uday A. Kilkami

Mechanical & Aerospace Engineering Theses & Dissertations

A major drawback of current cost estimation models is their incapability of embracing effectively complete product development stage. Parametric estimation works well in early stages of design, but in detail design stage, a more complete estimation is provided by process model based and detail estimation techniques. A major paradigm shift is proposed in this work whereby ‘Cost’ is to be considered as a design parameter from scientific perspective, and it is to be treated as a design consequence rather than as an operational outcome. A comprehensive framework using System Analysis fundamentals is designed to study ‘Process Cost’ aspects of part …

An Integrated Engineering-Computation Framework For Collaborative Engineering: An Application In Project Management, Hisham Mohamed El-Sayed Abdelsalam

Mechanical & Aerospace Engineering Theses & Dissertations

Today's engineering applications suffer from a severe integration problem. Engineering, the entire process, consists of a myriad of individual, often complex, tasks. Most computer tools support particular tasks in engineering, but the output of one tool is different from the others'. Thus, the users must re-enter the relevant information in the format required by another tool. Moreover, usually in the development process of a new product/process, several teams of engineers with different backgrounds/responsibilities are involved, for example mechanical engineers, cost estimators, manufacturing engineers, quality engineers, and project manager. Engineers need a tool(s) to share technical and managerial information and to …

Setpoint Tracking Predictive Control In Chemical Processes Based On System Identification, Sinchai Chinvorarat

Mechanical & Aerospace Engineering Theses & Dissertations

A Kraft recovery boiler in a pulp-paper mill provides a means for recovery of the heat energy in spent liquor and recovery of inorganic chemicals while controlling emissions. These processes are carried out in a combined chemical recovery unit and steam boiler that is fired with concentrated black liquor and which produces molten smelt. Since the recovery boiler is considered to be an essential part of the pulp-paper mill in terms of energy resources, the performance of the recovery boiler has to be controlled to achieve the highest efficiency under unexpected disturbances.

This dissertation presents a new approach for combining …