Engineering Commons^™

Development Of An Analytical Model For Beams With Two Dimples In Opposing Directions, Mofareh H. Ghazwani

Masters Theses

Structures such as beams and steel plates can produce potentially high levels of unwanted vibrations and noises in the environment. A method of improving the vibration and acoustic characteristics of beams based on introducing dimples on its surfaces will be presented in this study. This method focuses on creating two dimples in the same and opposite direction on beam’s surface where the effect of dimples on the change in beam’s natural frequencies is the problems of interest.

A boundary value model (BVM) is developed for a beam with two dimples and subjected to various boundary conditions using Hamilton’s Variational Principle. …

The Stability And Ecophysiological Realism Of Calibrated Parameters In A Detailed Vegetation Model (Waves), R. W. Vervoort, J. D. Henry, M. Gharun, M. A. Adams

International Congress on Environmental Modelling and Software

WAVES is a daily time-step one-dimensional vegetation, water and energy transfer model that has been used extensively across Australia (and globally) to simulate ecohydrological processes. In particular it has been used extensively for assessing future recharge under climate change. A literature review suggests parameter values from the user manual are most commonly used in research. This suggests that further investigation into the stability and equifinality of the parameters might be warranted, specifically since the model is used for scenario studies. This study made use of an extensive sapflow and soil moisture data set for 7 tree vegetation sites in the …

The Development Of A Prosthetic Training Software For Upper Limb Amputees, Tyler Kayne Sullins

USF Tampa Graduate Theses and Dissertations

The purpose of this study was to develop an intuitive software that aids in the field of prosthetic training and rehabilitation by creating an individualized visualization of joint angles. This software is titled “the prosthetic training software (PTS) for individualized joint angle representation”, and it enables the individualized portrayal of predicted or pre-recorded joint angles. The PTS is an intuitive program for clinicians and prosthesis users that produces an animation of a virtual avatar reflecting the user’s segment lengths and amputation for rehabilitation and training purposes.

The PTS consists of a graphical user interface (GUI) and a 3D visualization of …

Electrokinetics And Vacuum Combined Dewatering Of Oil Sand Tailings, Rui Zhang

Electronic Thesis and Dissertation Repository

One of the challenges faced by the oil sand industry is the dewatering of mature fine oil sands tailings (MFT) due to the low permeability. Vacuum pressure or electrokinetic (EK) dewatering is effective to meet this objective. This research was focused on the experimental study and analytical modelling to explore the influence of combined vacuum and EK treatment on MFT. In this study, systematical experiments on MFT recovered from the northern Alberta were carried out. At first, the characterization and EK cell tests were conducted to measure the basic properties and the coefficient of electroosmotic permeability (ke) of MFT. Secondly, …

Sysml Based Cubesat Model Design And Integration With The Horizon Simulation Framework, Shaun Luther

Master's Theses

This thesis examines the feasibility of substituting the system input script of Cal Poly’s Horizon Simulation Framework (HSF) with a Model Based Systems Engineering (MBSE) model designed with the Systems Modeling Language (SysML). A concurrent student project, SysML Output Interface Creation for the Horizon Simulation Framework, focused on design of the HSF Translator Plugin which converts SysML models to an HSF specific XML format. A SysML model of the HSF test case, Aeolus, was designed. The original Aeolus HSF input script and the translated SysML input script retained the format and dependency structure required by HSF. Both input scripts …

Ncma Groundwater Model Using Usgs Modflow-2005/Pest, Brian Matthew Wallace

Master's Theses

A numerical model for the NCMA aquifer complex is presented. The objective of the study is to develop a numerical groundwater model for the NCMA aquifer system to enhance the understanding of subsurface groundwater flow. Infiltration, streamflow, pumping, and return flows are implemented to characterize the aquifer complex over time. The numerical model is calibrated to municipal and monitoring well data, average monthly water balances, and hydraulic contours. Transient aquifer inflows and outflows are assessed in the results of the study and are compared to balance terms from previous studies. The 2007 Todd Engineers Study subsurface inflows and outflows generate …

An Automatic Algorithm For Textured Digital Elevation Model Formation Using Aerial Texel Swaths, Taylor C. Bybee

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The process of creating a 3D terrain map of an area is a challenging, computationally intensive task. There are two main camps of established methods doing this, with varying degrees of accuracy and cost. Using the established methods, there is a trade-off between accuracy and cost. The first method involves using many aerial images to detect disparity between points in the images. This is a difficult task as it requires a lot of computer processing with varying degrees of reliability. In addition, this method does not make any direct distance measurements. Secondly, using high-precision and high-cost lasers and positioning equipment, …

Potential Effects Of Climate Change On Ecologically Relevant Streamflow Regimes, Sulochan Dhungel, David G. Tarboton, Jiming Jin, Charles P. Hawkins

Civil and Environmental Engineering Faculty Publications

We assessed the climate-driven changes in ecologically relevant flow regimes expected to occur by the year 2100 in streams across the conterminous United States. We used long-term daily flow measurements from 601 gauged streams whose watersheds were in relatively natural condition to characterize spatial variation in 16 flow regime variables selected for their ecological importance. Principal component analysis of these 16 variables produced five uncorrelated factors that described patterns of spatial covariation in flow regimes. These five factors were associated with low flow, magnitude, flashiness, timing, and constancy characteristics of the daily flow regime. We applied hierarchical clustering to the …

Model Based Vehicle Simulation For Electrically Actuated Transmission Test Cells, Kenneth L. Gruel

Masters Theses

The Eaton Vehicle Group is responsible for the development of a large family of automotive products, including manual and automated manual transmissions for light, medium, and heavy duty vehicles. To further expand the transmission testing capabilities at Vehicle Group headquarters, the Vehicle Simulator system was developed and integrated into an existing motor-based test cell. System development time and cost were reduced by leveraging readily available vehicle models and real-time hardware. The Vehicle Simulator system allows a user to control the speed and torque settings of the test cell motors in manual mode, or switch the motors to vehicle emulation mode. …

Bayesian Learning And Predictability In A Stochastic Nonlinear Dynamical Model, John Parslow, Noel Cressie, Edward P. Campbell, Emlyn Jones, Lawrence Murray

Professor Noel Cressie

Bayesian inference methods are applied within a Bayesian hierarchical modelling framework to the problems of joint state and parameter estimation, and of state forecasting. We explore and demonstrate the ideas in the context of a simple nonlinear marine biogeochemical model. A novel approach is proposed to the formulation of the stochastic process model, in which ecophysiological properties of plankton communities are represented by autoregressive stochastic processes. This approach captures the effects of changes in plankton communities over time, and it allows the incorporation of literature metadata on individual species into prior distributions for process model parameters. The approach is applied …

Small Scale-Wind Power Dispatchable Energy Source Modeling, Jordan J. Cannon, David Moore, Stephen Eason, Adel El-Shahat

Department of Electrical & Computer Engineering Faculty Research & Publications

Due to the importance of Wind energy as an intermittent renewable resource in Micro-Grids applications; this paper is proposed. So this research proposal seeks to model and analyze components of a wind turbine generator (WTG) system to store energy and supply loads with the stored energy. Focus is placed on the storage of energy into a lead acid battery and using the battery with the inverter as a dispatchable energy source. The storage device and inverter acts as a steam power plant generator. The small-scale system consists of wind turbine, wind generator, loads, dc-dc converter, ac-dc inverter, controller and battery. …

3d Printed Teeth: Anatomically Correct Primary Replicas, Anh Nguyen, Stefan Harris

Capstone Design Expo Posters

The current method of molding teeth, especially primary teeth, cannot accurately reproduce internal tooth structures. Therefore, there is a need for primary teeth to be made anatomically accurate on-demand with the ability to customize a model for specific patients. This project aims that any tooth extracted digitally from a Dental Cone Beam computed tomography (CBCT) scan of a child's mouth can be 3D printed into an accurate replicate with which dental students can practice. Constraints include viable materials that can be printed by a 3D printer, represent tooth anatomy and provide desirable mechanical properties compatible with the dental drilling operation. …

Individual-Level Simulation Model For Cost Benefit Analysis In Healthcare, Nagesh Shukla, Vu Lam Cao, Van Hoang Phuong, Marian D. Shanahan, Alison Ritter, Pascal Perez

SMART Infrastructure Facility - Papers

Illicit drug use creates significant burden at societal, family and personal levels. Every year substantial resources are allocated for treatment and the consequences of illicit drug use in Australia and around the world. Heroin is one of the major forms of illicit drugs. Several independent heroin treatment strategies or interventions exist and state-of-the art research demonstrates their efficacy and relative costeffectiveness. However, assessing total potential gains and burden from providing all treatment interventions or varying the mix of heroin treatments has never been attempted. This paper proposed an individual-level simulation model (ISM) which addresses net social benefit over a lifetime …

Case Study: A Model Based Systems Engineering (Mbse) Framework For Characterising Transportation Systems Over The Full Life Cycle, William R. Scott, Richard Fullalove, Gary Arabian, Allan P. Campbell

SMART Infrastructure Facility - Papers

Development of transport infrastructure has significant challenges including acquisition lag, phased evolution, multiple disparate stakeholders and environment-specific issues. The Asset Standards Authority (ASA) at TfNSW is introducing MBSE to address these challenges. Instrumental to the introduction is the development of a framework that structures the available data and provides guidance and traceability between the data sets. This framework combines the enterprise-level drivers with the lower level drivers such as standards to outline a generic conceptual design for a transport system. This conceptual design is then used to guide future system development. The outcome is future project information based on greater, …

Analytic Performance Model For State-Based Mac Layer Cooperative Retransmission Protocols, Brett Hagelstein, Mehran Abolhasan, Daniel R. Franklin, Farzad Safaei, Wei Ni

Faculty of Engineering and Information Sciences - Papers: Part A

Cooperative retransmission can significantly improve link reliability over lossy and time-varying wireless links. However, comparing retransmission protocols is challenging, and generally requires simplistic assumptions specific to each protocol. In this paper, we develop a general model to evaluate cooperative retransmission protocols with distributed, slot-based contention algorithms. Specifically, we propose to calculate the relay time-out probabilities at a MAC time-slot scale, formulate retransmission outcomes as functions of the time-out probabilities, and derive the probability of a retransmission process for every data frame. We also propose a Markov extension of our model to characterise the dependency between retransmissions of multiple frames. This …

Microstructure And Micro-Texture Evolution During The Dynamic Recrystallisation Of A Ni-30fe-Nb-C Model Alloy, Parvez Mannan, Ahmed A. Saleh, Azdiar A. Gazder, Gilberto Casillas, Elena V. Pereloma

Faculty of Engineering and Information Sciences - Papers: Part A

The evolution of microstructure and micro-texture during discontinuous dynamic recrystallisation of an austenitic Ni-30Fe-Nb-C model alloy subjected to interrupted plane strain compression at strains (ε) of 0.23, 0.35, 0.68, 0.85 and 1.2 was investigated using electron backscattering diffraction and transmission electron microscopy. Throughout the strain range, the majority of dynamic recrystallisation events comprised nucleation in necklace-like arrangements located at and along grain boundaries via bulging. At ε ≥ 0.68, discrete nucleation events were also observed within grain interiors. Grain growth during dynamic recrystallisation is characteristic of strain induced boundary migration. The initial texture comprised Cube-RD ({013}〈100〉), Cube-ND ({001}〈310〉) and Cube …

A Data-Driven Predictive Model For Residential Mobility In Australia - A Generalised Linear Mixed Model For Repeated Measured Binary Data, Mohammad-Reza Namazi-Rad, Payam Mokhtarian, Nagesh Shukla, Albert Munoz

Faculty of Engineering and Information Sciences - Papers: Part A

Household relocation modelling is an integral part of the Government planning process as residential movements influence the demand for community facilities and services. This study will address the problem of modelling residential relocation choice by estimating a logit-link class model. The proposed model estimates the probability of an event which triggers household relocation. The attributes considered in this study are: requirement for bedrooms, employment status, income status, household characteristics, and tenure (i.e. duration living at the current location). Accurate prediction of household relocations for population units should rely on real world observations. In this study, a longitudinal survey data gathered …

Design-Oriented Stress–Strain Model For Concrete Under Combined Frp-Steel Confinement, G Lin, Tao Yu, Jin Guang Teng

Faculty of Engineering and Information Sciences - Papers: Part A

Extensive research has been conducted on fiber-reinforced polymer (FRP)-confined plain and RC columns, leading to a large number of stress–strain models. Most of these models have been developed for FRP-confined plain concrete and are thus applicable only to concrete in FRP-confined RC columns with a negligible amount of transverse steel reinforcement. The few models that have been developed for concrete under the combined confinement of FRP and transverse steel reinforcement are either inaccurate or too complex for direct use in design. This paper presents an accurate design-oriented stress–strain model for concrete under combined FRP-steel confinement in FRP-confined circular RC columns. …

A New Micro Scale Fe Model Of Crystalline Materials In Micro Forming Process, Liang Luo, Haibo Xie, Dongbin Wei, Xiaogang Wang, Cunlong Zhou, Zhengyi Jiang

Faculty of Engineering and Information Sciences - Papers: Part A

Micro forming of metals has drawn global attention due to the increasing requirement of micro metal products. However, the size effects become significant in micro forming processes and affect the application of finite element (FE) simulation of micro forming processes. Dividing samples into small areas according to their microstructures and assigning individual properties to each small area are a possible access to micro forming simulation considering material size effects. In this study, a new model that includes both grains and their boundaries was developed based on the observed microstructures of samples. The divided subareas in the model have exact shapes …

A Conceptual Model For The Application Of Business Analytics In The Horizontal Strategic Alliance, John Janosko, Tingru Cui, S K. Lau

Faculty of Engineering and Information Sciences - Papers: Part A

The formation of strategic alliances amongst organisations has grown in recent years as globalisation has opened new markets for firms to pursue. It is of ever-increasing importance that organisations have a thorough understanding of the performance of their alliance to achieve competitive advantage. However, much research on strategic alliance has focused on examining the organisations within the alliance rather than focusing on the alliance itself. Using the new discipline of business analytics, this paper proposes a hierarchical model blending the functional roles of business analytics with data standardisation and context mediation frameworks to allow business analytics to be applied to …

Modeling And Identification Of A Realistic Spiking Neural Network And Musculoskeletal Model Of The Human Arm, And An Application To The Stretch Reflex, Manish Sreenivasa, Ko Ayusawa, Yoshihiko Nakamura

Faculty of Engineering and Information Sciences - Papers: Part B

This study develops a multi-level neuromuscular model consisting of topological pools of spiking motor, sensory and interneurons controlling a bi-muscular model of the human arm. The spiking output of motor neuron pools were used to drive muscle actions and skeletal movement via neuromuscular junctions. Feedback information from muscle spindles were relayed via monosynaptic excitatory and disynaptic inhibitory connections, to simulate spinal afferent pathways. Subject-specific model parameters were identified from human experiments by using inverse dynamics computations and optimization methods. The identified neuromuscular model was used to simulate the biceps stretch reflex and the results were compared to an independent dataset. …

A Local Field Correlated And Monte Carlo Based Shallow Neural Network Model For Non-Linear Time Series Prediction, Qingguo Zhou, Huaming Chen, Hong Zhao, Gaofeng Zhang, Jianming Yong, Jun Shen

Faculty of Engineering and Information Sciences - Papers: Part A

Water resource problems currently are much more important in proper planning especially for arid regions, such as Gansu in China. For agricultural and industrial activities, prediction of groundwater status is critical. As a main branch of neural network, shallow artificial neural network models have been deployed in prediction areas such as groundwater and rainfall since late 1980s. In this paper, artificial neural network (ANN) model within a newly proposed algorithm has been developed for groundwater status forecasting. Having considered previous algorithms for ANN model in time series forecast, this new Monte Carlo based algorithm demonstrated a good result. The experiments …

Building A Microsimulation Model Of Heroin Use Careers In Australia, Alison Ritter, Nagesh Shukla, Marian D. Shanahan, Van Hoang Phuong, Vu Lam Cao, Pascal Perez, Michael P. Farrell

Faculty of Engineering and Information Sciences - Papers: Part A

Illicit heroin use is a worldwide problem, with significant health and social costs. Treatment is known to be effective in changing heroin use habits, but it often needs to be provided over a lifetime, with people cycling in and out of treatment. It is therefore important to capture a long-term perspective on heroin use careers. The aim of this project was to build a lifetime microsimulation model of heroin using careers. This paper describes the conceptual logic of the model, the input parameters and the verification and validation results. A microsimulation model was chosen as the most appropriate simulation platform …

Coupling A Thermal Comfort Model With Building Simulation For User Comfort And Energy Efficiency, Katharina Boudier, Massimo Fiorentini, Sabine Hoffmann, Raghuram Kalyanam, Georgios Kokogiannakis

Faculty of Engineering and Information Sciences - Papers: Part B

This paper describes a methodology for coupling an advanced model of the thermo-regulatory system of the human body that describes its physiological processes, a comfort model that evaluates thermal sensation and comfort, and the ESP-r building simulation software that computes the transient thermal response of a building model. The objective of this study was to utilise the physiology and comfort models to dynamically modify the heating and cooling temperature set points of a zone controller in ESP-r, in accordance with the computed human thermal sensation and achieve realtime thermal comfort management. The comunication between the software is managed by the …

Computational Assessment Of Neural Probe And Brain Tissue Interface Under Transient Motion, Michael Polanco, Sebastian Bawab, Hangsoon Yoon

Mechanical & Aerospace Engineering Faculty Publications

The functional longevity of a neural probe is dependent upon its ability to minimize injury risk during the insertion and recording period in vivo, which could be related to motion-related strain between the probe and surrounding tissue. A series of finite element analyses was conducted to study the extent of the strain induced within the brain in an area around a neural probe. This study focuses on the transient behavior of neural probe and brain tissue interface with a viscoelastic model. Different stages of the interface from initial insertion of neural probe to full bonding of the probe by astro-glial …

Interest Detection In Image, Video And Multiple Videos: Model And Applications, Yuewei Lin

Theses and Dissertations

Interest detection is detecting an object, event, or process that draws attention. In this dissertation, we focus on interest detection in images, video and multiple videos. Interest detection in an image or a video is closely related to visual attention. However, the interest detection in multiple videos needs to consider all the videos as a whole rather than considering the attention in each single video independently.

Visual attention is an important mechanism of human vision. The computational model of visual attention has recently attracted a lot of interest in the computer vision community mainly because it helps find the objects …

Kinetics Of Molten Metal Capillary Flow In Non-Reactive And Reactive Systems, Hai Fu

Theses and Dissertations--Mechanical Engineering

Wetting and spreading of liquid systems on solid substrates under transient conditions, driven by surface tension and viscous forces along with the interface interactions (e.g., a substrate dissolution or diffusion and/or chemical reaction) is a complex problem, still waiting to be fully understood. In this study we have performed an extensive experimental investigation of liquid aluminum alloy spreading over aluminum substrate along with corroboration with theoretical modeling, performed in separate but coordinate study. Wetting and spreading to be considered take place during a transient formation of the free liquid surface in both sessile drop and wedge-tee mating surfaces’ configurations. The …

Smart Material Actuation And Morphing For Unmanned Aircraft Systems, Caio H. Da Silva Lima

Honors Undergraduate Theses

The intent of this thesis is to outline the design, analysis, and characterization of an axially compressed piezocomposite actuator and, in particular, to determine the correlation and accuracy of two models used to predict deflection of an axially compressed piezocomposite bimorph. Restrictions in material properties lead to vehicle inefficiencies caused by the discontinuous geometry of deflected control surfaces in unmanned aircraft systems. This performance disadvantage in discrete control surfaces is caused in part by the sharp edges that are formed when the surface is pivoted. Flow continuity over the body of a vehicle is important in minimizing the effects of …