Engineering Commons^™

Hvac System Energy Audit For Leverett Elementary School, Connor Smalling

Biological and Agricultural Engineering Undergraduate Honors Theses

Leverett Elementary School is located in Fayetteville, AR. The school needs significant upgrades to its infrastructure. The Fayetteville Public School District has voted to pursue an Energy Services Performance Contract (ESPC) in order to finance the desired upgrades to Leverett Elementary, among other schools in the district.

The scope of this thesis was to perform an energy audit on the existing heating, ventilation, and air conditioning (HVAC) system. By using an energy modeling software, eQuest, the building and the existing base system were modeled to determine utility consumption. Three different HVAC system alternatives were analyzed against the base system by …

A Comparison Of The Army Corps Of Engineers Hydrologic Modeling System And Autodesk Storm And Sanitary Analysis For Hydraulic And Hydrologic Analysis And Design, Foster Josef Heifetz Campbell

Master's Theses

Hydrological and hydraulic effects of urban development is one of the key issues of study for improved water management. The addition of impervious surfaces to once pervious land and re-routing open channels and flow paths can cause flooding or declining water levels within a watershed. Many studies of these issues have found that there can be multiple factors causing hydrological and hydraulic impacts, and it can be hard to analyze and develop effective solutions without appropriate drainage software packages. However, there are multiple software packages available for use, and determining the correct one to use for a specific challenge can …

Investigation Of Subsurface Stratigraphy And Groundwater Dynamics In The Mississippi River Delta, An Li

LSU Doctoral Dissertations

The Mississippi River Delta (MRD) is socioeconomically important to the state of Louisiana and the United States. Various types of land-water system data have been collected in the MRD. However, very few efforts have been made to utilize these datasets in modeling regional stratigraphy and groundwater dynamics in the MRD, especially for the upper 50 m of the depth. In this interval of depth, the Mississippi River and surrounding interdistributary bays intensively interact with the groundwater system. The lack of knowledge in regional stratigraphy and groundwater dynamics hinder an understanding of how hydrogeological setting affects processes such as surface-groundwater interaction, …

Gesture Based Control Of Semi-Autonomous Vehicles, Brian Sanders

Computational Modeling & Simulation Engineering Theses & Dissertations

The objective of this investigation is to explore the use of hand gestures to control semi-autonomous vehicles, such as quadcopters, using realistic, physics based simulations. This involves identifying natural gestures to control basic functions of a vehicle, such as maneuvering and onboard equipment operation, and building simulations using the Unity game engine to investigate preferred use of those gestures. In addition to creating a realistic operating experience, human factors associated with limitations on physical hand motion and information management are also considered in the simulation development process. Testing with external participants using a recreational quadcopter simulation built in Unity was …

Modeling And Testing Powerplant Subsystems Of A Solar Uas, Luke J. Bughman

Master's Theses

In order to accurately conduct the preliminary and detailed design of solar powered Unmanned Aerial Systems (UAS), it is necessary to have a thorough understanding of the systems involved. In particular, it is desirable to have mathematical models and analysis tools describing the energy income and expenditure of the vehicle. Solar energy income models may include available solar irradiance, photovoltaic array power output, and maximum power point tracker efficiency. Energy expenditure models include battery charging and discharging characteristics, propulsion system efficiency, and aerodynamic efficiency. In this thesis, a series of mathematical models were developed that characterize the performance of these …

Molecular Modeling Of Tethered Polyelectrolytes For Novel Biomedical Applications, Merina Jahan

Theses and Dissertations

Current research trends throughout the world focus on designing intelligent materi- als and systems for diverse applications in all courses of life. Biomaterials research encompasses a major part in this revolution due to the increased effort in fulfilling unmet medical needs to treat complex physiological and neurodegenerative disorders. Polymers play inevitable roles in these research endeavors for their ubiquitous pres- ence in biological systems. Therefore, it is crucial to understand how the polymeric molecules interact within diverse biological environments, to efficiently engineer them for various drug delivery and biosensing systems. The use of experimental design and selection of different polymers …

Modeling Neutron Interaction Inside A 2d Reactor Using Monte Carlo Method, A. S. M. Fakhrul Islam

Theses and Dissertations

Scientists and engineers have been working for many years to develop accurate approaches to analyzing nuclear power reactors using computer codes that closely model the behavior of neutrons in a reactor core. The Monte Carlo simulation method is capable of treating complex geometries with a high level of resolution and fidelity to model neutron interactions inside a reactor core. With the requirement of accurate modeling in reactor physics and dynamics and great innovation of computer technology, Monte Carlo method is becoming an ever more powerful tool and receiving rising attention. In this study, Monte Carlo method is used to model …

Cubesat Astronomy Mission Modeling Using The Horizon Simulation Framework, Alexander W. Johnson

Master's Theses

The CubeSat Astronomy Network is a proposed system of multiple CubeSat spacecraft capable of performing follow-up observations of astronomical targets of interest. The system is intended to serve as a space-borne platform that can complement existing systems utilized for astronomical research by undergraduate and high school students. Much research and development work has been performed to develop model-based system engineering methodologies and products for CubeSat missions, including the Horizon Simulation Framework. The Horizon Simulation Framework enables the development of system models using the Extended Markup Language (XML), and its simulation program can generate system simulations over model-specified timespans. System requirements …

Comparison Of Heat Generation Models In Finite Element Analysis Of Friction Welding, Richard Verile Livingston

Theses and Dissertations

Finite element models of friction welding can be used to estimate internal conditions of welds which are useful for weld analysis and developing experimental welding procedures. Many modeling techniques are used to accomplish these goals, each with relative strengths and weaknesses. A comparative analysis of friction welding models using different heat generation methods is presented. The three different heat generation methods examined were viscoplastic friction, constant steady-state generation, and experimentally measured power data. The models were compared against each other using three output measurements: temperature, axial force, and upset. The friction model predicted temperatures within 40 degrees C. Temperature accuracy …

Doing A Lot With A Little: A Diagnostic Analysis Of Swmm To Simulate Hydrologic Behavior Within Lid Systems, Lucie Lynn Worthen

Theses - ALL

Low Impact Development (LID) aims to mitigate the hydrological impacts of urbanization by promoting evapotranspiration, storing and slowing the flow of water in formerly impervious areas. Green roofs, a form of LID often utilized in highly urbanized watersheds, are widely simulated using the Storm Water Management Model (SWMM). However, methods to improve diagnostic analysis of SWMM have lagged compared to other environmental disciplines. In this study, I utilize frugal diagnostic analyses to investigate potential sources of non-linearity, uncertainty, and equifinality within SWMM applied to a particular case study, the OnCenter green roof in Syracuse, New York. My findings highlight the …

Modeling And Characterization Of A Ring-Resonator Based Silicon Photonic Sensor On Silicon-On-Insulator (Soi), Gwangho Choi

Graduate Theses - Physics and Optical Engineering

The purpose of this work is to build silicon photonic devices and verify their functionalities. In particular, the structure of a ring resonator (RR) is analyzed and applied to various silicon photonic application in sensing. Silicon waveguides, grating couplers, directional couplers, and RRs are fabricated on the silicon-on-insulator (SOI) wafer. Geometrical parameters and optical properties of the silicon devices are studied and also applied to the design of the aforementioned devices. The waveguide dimensions and, optical properties of the silicon waveguide such as dispersion and effective-index are examined. The RRs are made of a series of straight and bent waveguides …

Modeling And Validation Of Tissue Optical Properties In The Photon Transport Regime, Katelyn Heath

Biomedical Engineering Undergraduate Honors Theses

Early detection of changes in epithelial cells, such as the development of neoplastic formations seen in epithelial dysplasia, can indicate regions of the epithelial tissue that are at a high risk for cancerous formation. Using concepts from diffuse reflectance spectroscopy, a Monte Carlo model was developed to predict the reflectance measured by a detector at a small source-detector separation on a microendoscope. The Monte Carlo results were then used to calculate a mathematical relationship between the reflectance and distance that can be used to determine optical properties in a tissue sample. This model was validated with liquid phantoms of specified …

Simulating Alternative Tuberculosis Diagnosis Methods In Underdeveloped Countries, Luke Turner

Industrial Engineering Undergraduate Honors Theses

Tuberculosis is the deadliest infectious disease in the world; it is especially rampant in underdeveloped countries because they do not have the infrastructure, technology, or funding to properly combat the infection. However, the development of portable point-of-care diagnosis machines can reverse this epidemic as they far surpass conventional laboratory identification. The question now is where to place these machines, which is a difficult decision with a lack of data. Therefore, a flexible simulation model is created to test the implementation of these machines with different countries and configurations. The simulation tests the baseline model and three proposed implementations of the …

Detection And Classification Of Vibrating Objects In Sar Images, Francisco German Perez Venegas

Electrical and Computer Engineering ETDs

The vibratory response of buildings and machines contains key information that can be exploited to infer their operating conditions and to diagnose failures. Furthermore, since vibration signatures observed from the exterior surfaces of structures are intrinsically linked to the type of machinery operating inside of them, the ability to monitor vibrations remotely can enable the detection and identification of the machinery.

This dissertation focuses on developing novel techniques for the detection and M-ary classification of vibrating objects in SAR images. The work performed in this dissertation is conducted around three central claims. First, the non-linear transformation that the micro-Doppler return …

Three-Dimensional Collagen Tubes For In Vitro Modeling, Rebecca Jones

Theses and Dissertations

Collagen type I represents a novel material for three-dimensional in vitro models. While two-dimensional models are typically inadequate for recreating the complex processes of the body, collagen provides a three-dimensional basis with a variety of applications, including remodeling of vascular cells under tension and vascular stenosis. Smooth muscle cells reorganize and reconstruct their environment differently under conditions of tensions, such as with sutures, or under conditions without applied external tension. Vascular stenosis, the abnormal narrowing of blood vessels, arises from defective developmental processes or atherosclerosis-related adult pathologies. Stenosis triggers a series of adaptive cellular responses that induces adverse remodeling, which …

Lumped Parameter Modeling And Parameter Investigation Of An Electrohydraulic Crimping Hand Tool, Eric Norquist

Master's Theses (2009 -)

A lumped parameter model of a hand-held electrohydraulic tool was developed. The tool modeled was a Milwaukee Tool M18 12 Ton Crimper. First principle approaches were used to develop state-space models for each of the subsystems in the tool. The included subsystems were the tool motor and gear train, pump, return valve, and cylinder. The subsystem models were combined into a comprehensive eleventh-order nonlinear dynamic tool model. The tool model has two inputs and three outputs. The model inputs were the motor voltage and opening the return valve. The outputs were the motor current, application time, and retraction time. Each …

Designing An On-Demand Dynamic Crowdshipping Model And Evaluating Its Ability To Serve Local Retail Delivery In New York City, Shirin Najaf Abadi

Dissertations and Theses

Nowadays city mobility is challenging, mainly in populated metropolitan areas. Growing commute demands, increase in the number of for-hire vehicles, enormous escalation in several intra-city deliveries and limited infrastructure (road capacities), all contribute to mobility challenges. These challenges typically have significant impacts on residents’ quality-of-life particularly from an economic and environmental perspective. Decision-makers have to optimize transportation resources to minimize the system externalities (especially in large-scale metropolitan areas). This thesis focus on the intra-city mobility problems experienced by travelers (in the form of congestion and imbalance taxi resources) and businesses (in the form of last-mile delivery), while taking into consideration …

Analysis And Control Of Fiber-Reinforced Elastomeric Enclosures (Frees), Soheil Habibian

Master’s Theses

While rigid robots are extensively used in various applications, they are limited in the tasks they can perform and can be unsafe in close human-robot interactions. Soft robots on the other hand surpass the capabilities of rigid robots in several ways, such as compatibility with the work environments, degrees of freedom, manufacturing costs, and safe interactions with the environment. This thesis studies the behavior of Fiber-Reinforced Elastomeric Enclosures (FREEs) as a particular type of soft pneumatic actuator that can be used in soft manipulators. A dynamic lumped-parameter model is created to simulate the motion of a single FREE under various …

Synergistic Environmental Aging Of Glass Reinforced Polymer Composites, Tianyi Lu

Electronic Theses and Dissertations

Synergistic effects involved in the environmental degradation of Glass Reinforced Polymer (GRP) composites were examined and a novel synergistic aging model was proposed in this study. Six GRPs based on glass fibers with four different polymer resins and six pure polymer thermoplastic resins were exposed either individually or in combination to ultraviolet (UV) radiation, water condensation and elevated temperature for approximately 1000 h. The composites and polymers were monitored for weight changes as a function of time and their surfaces were examined after the tests using optical and scanning electron microscopes (SEM). Photodegradation of the polymer matrices was analyzed by …

The Role Of Ephemeral Stratification, Anoxia, And Entrainment In Mediating Spatiotemporal Trophic State Dynamics In A Lake Michigan Drowned River Mouth System (Mona Lake, Mi), Hayden Henderson

Dissertations, Master's Theses and Master's Reports

Mona Lake, MI (a drowned river mouth system) has become eutrophic as result of cultural eutrophication. The integrated monitoring effort and subsequent modeling (LAKE2K) reported on here has shifted the management focus to internal phosphorus loads (60 percent of annual load, 90 percent of load during the stratified and anoxic period) as a necessary precursor to trophic state change. Sediment phosphorus release can yield extreme elevations (> 1 mgSRP/L) of bottom water soluble reactive phosphorus (SRP), with blooms of potentially toxic cyanobacteria (largely Microcystis) occurring annually. Such blooms are ascribable to stochastic mixing and phosphorus entrainment to the surface waters, …

Development Of A 2d Scr Catalyst On A Diesel Particulate Filter Model For Design And Control Applications To A Ultra Low Nox Aftertreatment System, Venkata Chundru

Dissertations, Master's Theses and Master's Reports

This research focuses on modeling and control of PM and NO_x in diesel engine exhaust using an SCR catalyst on a Diesel Particulate Filter (SCR-F). A 2D SCR-F model was developed that is capable of predicting internal states: 2D temperature, PM and NH₃storage distributions and filtration efficiency, pressure drop, PM mass retained in the PM cake and substrate wall and outlet NO, NO₂and NH₃concentrations. The SCR-F model was used to simulate a DOC + SCR-F + DOC + SCR ultra-low NOx system that can achieve > 99.5% NOx conversion efficiency.

The model was calibrated …

Computational Modeling And Simulations Of Condition Deterioration To Enhance Asphalt Highway Pavement Design And Asset Management, Zul Fahmi Bin Mohamed Jaafar

Electronic Theses and Dissertations

A nation’s economy and prosperity depend on an efficient and safe transportation network for public mobility and freight transportation. A country’s road network is recognized as one of the largest public infrastructure assets. About 93 percent of 2.6 million miles of paved roads and highways in the United States (U.S.) are surfaced with asphalt. Longitudinal roughness, pavement cracking, potholes, and rutting are the major reasons for rehabilitation of asphalt roads. Billions of dollars are required annually for the maintenance and rehabilitation of road networks. If timely maintenance and rehabilitation are not performed, the pavement damages inflicted by heavy traffic repetitions …

Dynamic Discrepancy Reduced Order Modeling For Fischer-Tropsch Synthesis Over Cobalt-Based Catalyst, Jose Miguel Bohorquez

Graduate Theses, Dissertations, and Problem Reports

Advances in carbon capture techniques and demands in alternative fuel sources have increased over the past couple of decades. The Fischer-Tropsch Synthesis (FTS) provides a viable way to produce hydrocarbons from natural gas, coal, CO₂, or biomass. However, current comprehensive models for FTS encompass large number of reacting species, readsorption and conversion of primary products, surface intermediates, and coverage-dependent reaction rates. To accurately predict the products obtained through the process a reduced order model has been developed. By reducing the number of parameters of an existing comprehensive model, uncertainty is introduced. The uncertainty can be quantified by using …

As-Manufactured Modeling Of A Mistuned Turbine Engine Compressor Evaluated Against Experimental Approaches, Daniel L. Gillaugh

Browse all Theses and Dissertations

As-manufactured rotors behave quite differently than nominal, as-designed rotors due to small geometric and material property deviations in the rotor, referred to as mistuning. Traditional integrally bladed rotor (IBR) modeling approaches assume each blade is identical. State-of-the-art IBR dynamic response predictions can be accomplished using asmanufactured models (AMM) generated via optical topography measurements and mesh morphing. As-manufactured models account for geometric deviations occurring through the machining process, material deviations and field wear, allowing each blade to respond differently. Rotor designs are intended to avoid resonance crossings throughout an engine’s operating range, but total avoidance is challenging. This has led to …

Using Cfd To Improve Off-Design Throughflow Analysis, Troy J. Lanchman

Browse all Theses and Dissertations

In turbomachinery design, complex internal flows give rise to significant losses and blockage whose effects are difficult to properly analyze without detailed computational fluid dynamics (CFD) methods or experiments. In a typical design method, CFD is used in conjunction with simpler throughflow or cascade codes to hasten the process. However, the lesser physical accuracy of the design codes demands the inclusion of models to improve the accuracy of the throughflow codes. This thesis aims to use CFD data to generate improved loss and blockage models for a 2D compressor throughflow code by matching throughflow data to CFD data using optimizations. …