Engineering Commons^™

Investigation Of Ternary Binder Based Systems In Terms Of Calorimetry, Shrinkage And In-Situ Xrd, Anxhelina Qorllari, Elsa Qoku, Thomas A. Bier, Teuta Dilo

UBT International Conference

Ternary binders are defined in this study as compositions of Calcium Aluminate Cement (CAC), Ordinary Portland Cement (OPC) and Calcium Sulfate (CS̅). Several mixtures were studied, calorimetric and shrinkage technique has been used to follow the hydration during 24 hours. The XRD technique is used as support in the analysis of the hydration products. The results have shown that the initial amount of ��� and �� play a key role in the hydration of ��/���/�� mixtures and especially affect the formation of ettringite. The mechanism of reactions (hydration kinetic) and the reactions speed (acceleration or retardation) depends by the aggregates …

Reducing The Porosity And Sealing Cracks By Using Crystalline Admixture In Conventional Concrete, Visar Krelani, Liberato Ferrara

UBT International Conference

There is a continuous increase of quality on civil engineering materials in developed countries and parallel increase of need for new constructions in developing countries. Professional community should propose solutions for the durability that can resist in different severe environments. The most important factor that can affect concrete durability is represented by the pore distribution. Transport properties can take place through the porous network inside the cementitious composites and the aggregates interface, permitting the ingress of aggressive agents damaging concrete function intrinsically as a material and the wellfunctioning of the entire structure. The use of a crystalline admixture during the …

Using Of Proper Pavement Material For The Intersections With Slow-Moving Traffic, Bekim Selimi

UBT International Conference

Use of proper pavement material for some of intersections need special attention by road designers. At Camp Bondsteel-Kosovo on 2002 were built four road intersections using the concrete as pavement material. Heavy and slow-moving trucks that are turning or accelerating exposed these intersections to some of the highest stress level. After some years this intresections start deteriorating on their surface due to friction. The concrete pavements did not survive this period of usage and after eight years were removed and replaced with asphalt pavements. After more than seven years, the asphalt has shown minor distress but is still in good …

Heritage Under Pressure The Case Of The “Bypass” In Gjirokastra World Heritage Site Albania, Kreshnik Merxhani, Valmira Bozgo

UBT International Conference

The following article is an account presenting a professional movement opposing a planned and approved project for the construction of a new road known as the “Bypass”, which endangered the Historic Center of Gjirokastra. The project, consisted in the construction of a new road, with the initial aim of diverting automobile traffic from the Bazaar, turning it into a pedestrian zone. However after a few procedural problems were noted, it became clear that the project itself was not fulfilling its original aim, and further more posed a threat to the historical center. During the only public consultation session held for …

The Influence Of The Radius Of The Curve And The Lateral Slope On The Safety Of The Vehicle, Baxhuku Visar, Koca Odisea, Çekiçi Visar

UBT International Conference

The movement of the vehicle in a curve related to the construction of the road is expressed through the influence of the radius of the curve and the transversal inclination of the road. Two of these quantities are fixed quantities ever since the projection and then construction phase of the road. During the vehicle’s movement in the curve, their influence is shown through the critical slide velocity. This critical velocity is defined from the influence of the centrifugal force. For smaller values under critical velocity, this influence is expressed through the safety of the movement or the comfort of the …

Developing A New Total Sediment Transport Formula, Davut Okeu, Sokol Xhafa, Sevdije Govori, Majlinda Daci

UBT International Conference

Sediment transport is one of the most powerful factor on river hydrology. It has vital importance for water engineering projects. There are many sediment transport formulas in the literature but most of them are derived from small data sets of natural rivers or experimental designs. Each formulation has its own restrictions, which depends on the original dataset of that study. None of them have gained universal acceptance. As a result, investigation towards the development of more accurate and simpler formulae is still necessary and should be continued.

The aim of this study is to derive a new total sediment load …

Negative Impacts (Sbs) In Residential Buildings Case Studies From Kosovo, Muhamet Ahmeti, Mimoza Sylejmani

UBT International Conference

This paper presents the negative impacts on residential buildings in Kosovo, - as well as the main factors of the occurrence of sick building syndrome (SBS) in residential buildings in the case of Kosovo. It also examines the impact of different materials on this phenomenon and how many constructions in Kosovo are protected from this phenomenon.

For the assessment of the impact of materials on health and the environment, it is necessary to consider all the phases. Starting from the phase of construction, selection of materials, application from the beginning of the use of the building, including all the materials …

Capacity Design For R/C Structures According To En 1998-1:2004, Xhemshir Mulliqi

UBT International Conference

Capacity Design is a design process in which it is decided which objects within a structural system will be permitted to yield (ductile components) and which objects will remain elastic (brittle components). Material nonlinearity need only be modeled for ductile components, while components which will not yield need only consider elastic stiffness properties. In this design philosophy the capacity design approach that is currently used in practice demands strong column/weak beam frames or wall equivalent dual frames, with beam sway mechanisms, trying to involve plastic hinging at all beam ends.This paper aims to present Capacity design procedure for reinforced concrete …

Seismic Actions Induced By Cladding Panels On Precast Concrete Frame Structures, Bruno Del Lago, Francesco Foti, Luca Martinelli

UBT International Conference

The strong earthquakes occurred in Southern Europe in the last decade pointed out a poor seismic performance of the connection system of the cladding of precast industrial structures. The cladding of these buildings usually consists of sandwich concrete panels of remarkable mass, connected to the frame structure with mechanical devices. The estimation of the out-of-plane seismic action on these connections is a key step for their correct proportioning. However, the formulation currently provided in the Eurocode 8 for the estimation of the seismic action on non-structural elements was calibrated with different objectives. Furthermore, given there is no in-plane structure-panel interaction, …

The Effect Of Particles Pm10 And Pm2.5 In Dust Emission Of Urban Infrastructure From Thermal Power Plant Technology Kosovo, Afrim Syla

UBT International Conference

Airborne particulate matter with aerodynamic diameters less than 10 microns (referred to as PM10) is one of the six criteria pollutants used by the U.S. Environmental Protection Agency as indicator of air quality. During the last decade, the health effects of urban aerosols have become a major concern for the society.

The main environmental problems in Kosovo include all issues related to water supply and sanitation system, air quality, solid waste management and urban infrastructure. The major problem remains high pollutions, energy losses and low collection efficiency. The awareness of environmental issues among the general public is poor. Air quality …

P.M. 2.5 And Air Pollution In Prishtina, Rushiti Bardh, Futko Annea, Zeka Blin, Musliu Afete

UBT International Conference

High concentration of fine particles, the primary concern of worsening air pollution in Prishtina is believed to be fast paced economic and infrastructural growth in the capital of Kosova. This study is mainly focused on measuring the fluctuations of one constituent of air pollution, P.M. 2.5 (which are particles ranging from 2.5 to 10 micro-meters suspended into the environment). The measurements were done in Prishtina, mainly in the parts more frequented by people. Exposed to mixed combustion emission from roads with traffic, construction areas, and/or burning trash are a case of peculiar concern to people near those places. However, due …

Optimal Design Of Grillage Structures With Steel Crossed Beams Using Genetic Algorithms, Ersilio Tushaj, Niko Lako, Fatjon Saliu

UBT International Conference

The optimal problem in the structural design is an important issue in the engineering design. Various authors have analyzed the optimization of steel structures using algorithmic approaches. These techniques are generally grouped in deterministic or meta-heuristic techniques. From the introduction of structural optimization in the 1960’ up to now, various methods have been proposed. A genetic algorithm, is built and applied in this study using MatLab soft R2017a to a crossed beams system. The structural analysis is done with the direct stiffness method with constraints verification based on EuroCode 3:2005 criteria. Results are reported in the study.

The Effect Of Elevated Temperature On The Lightweight Concrete Containing Waste Pet Aggregate, Semiha Akçaözoğlu

UBT International Conference

In this study, the effect of waste PET as lightweight aggregate (WPLA) replacement with conventional aggregate on the some physical and mechanical properties and residual compressive strength of concrete was investigated. For this purpose, five different mixtures were prepared (the reference mixture and four WPLA mixtures including 30%, 40%, 50% and 60% waste PET aggregate by volume). The fresh and dry unit weights, compressive strengths, flexural-tensile strengths, water absorption and porosity ratios of the mixtures were measured. In addition the specimens exposed to elevated temperatures at 150, 300 and 450 °C and the residual compressive strengths were measured. Test results …

Beam- Column Joints For R/C Structures According To En 1998-1:2004, Xhemshir Mulliqi

UBT International Conference

Joints are crucial zones for the transfer internal forces effectively between the connecting elements like beams and columns .The behaviour of reinforced concrete moment resisting frame structures in recent earthquakes all over the world has highlighted the consequences of poor performance of beam column joints. The basic requirement of design is that the joint must be stronger than the adjoining hinging members, usually the beams or columns. This paper aims to present design approach for Beam- Column joints for reinforced concrete (R/C) structures according to the EN 1998-1:2004.

The Effect Of Fine Material Amount On Optimum Water Content Of Roller Compacted Concrete, Kubilay Akçaözoğlu, Bedrettin Menemencioğlu

UBT International Conference

In this study the effect of fine material amount on the optimum water content of roller compacted concrete (RCC) was investigated. The fine aggregate was replaced with calcite which maximum particle size was 63 μ, in amount of 0%, 2%, 4%, 6%, 10% and 14% by weight of total aggregate. Six different mixtures were prepared in the study. The optimum water contents of the mixtures were determined by using modified proctor test. Optimum water content, maximum dry unit weight and maximum fresh unit weight of produced specimens were measured. Optimum water content of specimens decreased depending on increasing fine aggregate …

Performance Of Mud Mortar Walls Under Seismic Loading, Christian L. Berneking Vi, Santiago Pujol, Prateek Pratap Shah, Lucas Laughery

The Summer Undergraduate Research Fellowship (SURF) Symposium

The inherently brittle nature of unreinforced masonry structures results in poor performance during earthquakes, presenting major hazards to communities. Many of these structures found in Nepal were severely damaged or destroyed during two earthquakes in 2015. The purpose of this project is to test the effect on seismic response of several modifications to stone and mud mortar structures. These structures are common in many areas of Nepal. Two T-shaped stone and mud mortar masonry walls are constructed. The first wall has no modifications and represents current building practices. The second wall uses steel wire mesh as external reinforcement. Each wall …

Buckling Of Cylindrical Shells Under Wind Loading, Tianlong Sun, Eyas Azzuni, Sukru Guzey

The Summer Undergraduate Research Fellowship (SURF) Symposium

Cylindrical shells such as aboveground steel storage tanks are widely used to store gases, chemicals and fuels. Stiffener rings are introduced to prevent cylindrical shells from buckling due to wind loads. The current top wind stiffener design rules used in the USA for such cylindrical storage tanks are specified in API 650. However, the design methodology of top stiffener rings is overly conservative. Therefore, relaxation of the design rules for the top stiffener is investigated in this study. The API 650 mandated top stiffener size was reduced to the same size as the mandated intermediate stiffener ring in this study. …

Full-Water Column Turbulence Parameterization Of Stratified Waters In Southern Lake Michigan, Kyla A. Prendergast, Cary D. Troy, David Cannon

The Summer Undergraduate Research Fellowship (SURF) Symposium

Full water column mean flow and turbulence structure was characterized at two stratified locations in Lake Michigan (a. Muskegon, MI; b. Michigan City, IN) in order to better understand the filtration potential of invasive quagga mussels. Invasive quagga mussels in Lake Michigan are filter feeders and can dramatically alter clarity as well as the biological/chemical characteristics of the water column. This filtering capacity is highly contingent on turbulence characteristics throughout the water column, which is poorly understood in the Great Lakes. Using velocity, temperature, and turbulence data collected from these locations, the structure of the water column turbulence was modeled …

Purdue Airsense: An Affordable Way To Measure And Study Air Pollution, Stephane Junior Nouafo Wanko, Shadi Tariq Azouz, Ruihang Du, Brandon Boor, Greg Michalski

The Summer Undergraduate Research Fellowship (SURF) Symposium

Air pollution is a major health hazard worldwide, accounting for one-eighth of all deaths in 2012 (World Health Organization). Globally, there is a severe lack of ground-based spatiotemporal monitoring of gaseous and particulate air pollutants, particularly in Africa, South and Central America, and the Middle East. This is in great part due to the high costs of air quality instrumentation that meet accuracy and reliability criteria set by monitoring agencies. The air quality data that is available is often not presented to the public in a user-friendly manner. Taking advantage of recent developments in low-cost sensing technologies, an integrated sensor …

Evaluation Of Radiation And Design Criteria For A Lunar Habitat, Hayley E. Bower, Daniel Gomez, Antonio Bobet, Julio A. Ramirez, Shirley J. Dyke, H. Jay Melosh

The Summer Undergraduate Research Fellowship (SURF) Symposium

Extraterrestrial habitation has long been the object of science fiction, and experts in the fields of science and engineering have proposed many designs for a lunar base. The research conducted has focused on either structural stability, radiation protection, or meteorite-impact vulnerabilities, but rarely have these been considered together. The Resilient ExtraTerrestrial Habitats (RETH) project aims to design a lunar habitat from a hazards perspective, considering general degradation, meteorite impacts, seismic activity, radiation exposure, thermal extremes, and geomagnetic storms in addition to the physiological, psychological, and sociological aspects of astronauts living in such a habitat. Several members of the RETH team …

Hazard Assessment Of Meteoroid Impact For The Design Of Lunar Habitats, Herta Paola Montoya, Shirley Dyke, Julio A. Ramirez, Antonio Bobet, H. Jay Melosh, Daniel Gomez

The Summer Undergraduate Research Fellowship (SURF) Symposium

The design of self-sustaining lunar habitats is a challenge primarily due to the Moon’s lack of atmospheric protection and hazardous environment. To assure safe habitats that will lead to further lunar and space exploration, it is necessary to assess the different hazards faced on the Moon such as meteoroid impacts, extreme temperatures, and radiation. In particular, meteoroids pose a risk to lunar structures due to their high frequency of occurrence and hypervelocity impact. Continuous meteoroid impacts can harm structural elements and vital equipment compromising the well-being of lunar inhabitants. This study is focused on the hazard conceptualization and quantification of …

Electrochemical Removal Of Lead In Water With Multi-Wall Carbon Nanotube Filters, Benjamin M. Stryker, Sol Park, Zhi Zhou

The Summer Undergraduate Research Fellowship (SURF) Symposium

Heavy metals, such as lead, are highly toxic and typical removal techniques are costly for household applications; causing serious public health risks and economic burdens. Previous studies using electrochemical filtration showed that singe-wall carbon nanotube membranes (SWCNTs) were effective at removing lead, but the use of less expensive multi-walled carbon nanotubes (MWCNTs) has not been fully explored. Therefore, there is a critical need to determine if MWCNTs are cost-effective for the removal of lead in water. The removal efficiency of lead(II) ions in an aqueous solution was evaluated in a flow-through filtration system over 50 minutes at 1.5 mL/min. Calcium …

Compliant Curb Ramp Solutions, Katherine Smutzer

Purdue Road School

Public Rights of Way Accessibility Guidelines (PROWAG) for Curb Ramps. Answers to frequently asked questions for Curb Ramps and Curb Ramp Designs. Examples of curb ramp designs in restricted conditions and other types of curb ramp examples.

Mash Implementation For Guardrail, Katherine Smutzer

Purdue Road School

A review of the Manual for Assessing Safety Hardware (MASH) Implementation for w-beam guardrail. What will change and what designers need to know when moving to MASH.