Engineering Commons^™

A New Method Of Producing High Strength Oil Palm Shell Lightweight Concrete, Hilmi Mahmud

Hilmi Mahmud

This paper presents a new method to produce high strength lightweight aggregate concrete (HSLWAC) using an agricultural solid waste, namely oil palm shell (OPS). This method is based on crushing large old OPS. Crushed OPS are hard and have a strong physical bond with hydrated cement paste. The 28 and 56. days compressive strength achieved in this study were about 53 and 56. MPa, respectively. Furthermore, it was observed that it was possible to produce grade 30 OPS concrete without the addition of any cementitious materials. Compared to previous studies, significantly lower cement content was used to produce this grade …

Effect Of Copper Addition On Mechanical Properties And Electrical Conductivity Of Pp/C-Cu Bipolar Plate Composites, Anne Zulfia, Taufik Abimanyu, Verina Warga Dalam

Makara Journal of Technology

Effect of Copper Addition on Mechanical Properties and Electrical Conductivity of PP/C-Cu Bipolar Plate Composites. Bipolar plate is a major component in PEM fuel cell which possess main function of collecting and removing electrons from anode to cathode. Therefore, materials for bipolar plates produced must have high electrical conductivity. To obtain bipolar plate materials which is cheap, lightweight and high conductivity, so it is developed bipolar plates material based on PP/C-Cu composite. PP/C-Cu composites has been made by mixing all materials then compounding, rheomix, hot blending and hot press. Cu (Copper) has been used various from 0.1 wt%, 1 wt% …

Medium Density Fibreboard Made Of Acetylated Sludge From Paper Mill, Luthfi Hakim, Evalina Herawati, I Nyoman Jaya Wistara

Makara Journal of Technology

Medium Density Fibreboard Made of Acetylated Sludge from Paper Mill. Research of using sludge as raw material for making medium density fibreboard (MDF) was useful to create additional value of sludge. The objective of the research was to evaluate physical properties, mechanical properties, and durability of MDF from acetylated sludge in 4 levels of acetate anhydride (0%, 3%, 5%, and 7%) with 3 replicates. The MDF was made using dry process. After materials were mixed with adhesives, they were pressed using hotpress under 170 oC temperature and 45 Pa pressure for 25 minutes. The size of the MDF sample was …

Effect Of Particle Size, Binder Content And Heat Treatment On Mechanical Properties Of 13-93 Bioactive Glass Scaffolds, Krishna C. R. Kolan, Ming-Chuan Leu, Greg Hilmas, Mariano Garcia Velez

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Particle size, binder content and the post-processing schedule are important parameters that affect the microstructure, and, hence, the mechanical properties of parts produced using the indirect selective laser sintering process. 13-93 bioactive glass, with mean particle sizes ranging from 10 μm to 44 μm, is mixed with different amounts of stearic acid binder to fabricate green scaffolds. Through the design of the post-processing schedule, the time required for postprocessing the green scaffolds is reduced from the initial 80 hrs to 12 hrs. The compressive strength varies from 41 MPa for a part with~60% porosity to 157 MPa for a part …

Shear Behaviour Of Reinforced Palm Kernel Shell Concrete Beams, Hilmi Mahmud

Hilmi Mahmud

The shear behaviour of palm kernel shell concrete (PKSC) beams prepared using palm kernel shell (PKS) as lightweight aggregate (LWA) is reported here. The shear strength of grade 30 PKSC with a density of 1850 kg/m(3) was found 24% higher than the corresponding normal weight concrete (NWC). Good aggregate interlock in PKSC was evident as it produced shorter jagged cracks compared to longer plain cracks of NWC. Further, PKSC was able to produce twice as many flexural and shear cracks compared to NWC. Tension stiffening between the tensile cracks of PKSC enhanced flexural rigidity and dowel action. The non-linear numerical …

Enhancement And Prediction Of Modulus Of Elasticity Of Palm Kernel Shell Concrete, Hilmi Mahmud

Hilmi Mahmud

This paper presents results of an investigation conducted to enhance and predict the modulus of elasticity (MOE) of palm kernel shell concrete (PKSC). Scanning electron microscopic (SEM) analysis on palm kernel shell (PKS) was conducted. Further, the effect of varying sand and PKS contents and mineral admixtures (silica fume and fly ash) on compressive strength and MOE was investigated. The variables include water-to-binder (w/. b) and sand-to-cement (s/. c) ratios. Nine concrete mixes were prepared, and tests on static and dynamic moduli of elasticity and compressive strength were conducted. The SEM result showed presence of large number of micro-pores on …

High-Strength Rice Husk Ash Concrete Incorporating Quarry Dust As A Partial Substitute For Sand, Hilmi Mahmud

Hilmi Mahmud

Quarry dust is a by-product from the granite crushing process in quarrying activities. This paper presents the findings from experimental work undertaken to evaluate the suitability of quarry dust as a partial substitute for sand in high-strength concrete (HSC) containing rice husk ash (RHA). Two grades of HSC mixes, to achieve 60 MPa and 70 MPa at 28 days, were designed with and without the incorporation of RHA. Quarry dust was then used in the mixes containing RHA as a partial substitute for sand, in quantities ranging from 10% to 40%. The slump of the fresh concrete and the compressive …

Understanding The Effects Of Addition Of Copper Nanoparticles To Sn-3.5 Ag Solder

A.S. Md Abdul Haseeb

Purpose - The purpose of this paper is to focus on the fabrication of SAC nanocomposites solder and discuss the effects of nanoCu addition on the structure and properties of resulted nanocomposite solder. Design/methodology/ approach - Ball milling is a nonequilibrium processing technique for producing composite metal particles with submicron homogeneity by the repeated cold welding and fracture of powder particles. This method is believed to offer good processablity, precise control over the solder composition, and produce more homogeneous mixture. Findings - It is found that the melting temperature, the wetting behaviour, and hardness are improved when the Cu nanoparticles …

Microstructure And Mechanical Properties At Different Length Scales And Strain Rates Of Nanocrystalline Tantalum Produced By High-Pressure Torsion, Q. Wei, Z. L. Pan, X. L. Wu, B. E. Schuster, L. J. Kecdkes, R. Z. Valiev

US Army Research

Fully dense, nanocrystalline tantalum (average grain size as small as ~40 nm) has been processed for the first time by high-pressure torsion. High-resolution transmission electron microscopy reveals non-equilibrium grain boundaries and grains decorated with high-density dislocations. Microhardness measurements and instrumented nanoindentation experiments indicate that the mechanical property is quite uniform except for the central area of the disks. Nanoindentation experiments at different strain rates suggest that the strain rate sensitivity of nanocrystalline tantalum is increased compared to the coarse- and ultrafine-grained counterparts and is accompanied by an activation energy of the order of a few ~b3 (b is the magnitude …

A New Method Of Producing High Strength Oil Palm Shell Lightweight Concrete, Zamin Jumaat

Zamin Jumaat

This paper presents a new method to produce high strength lightweight aggregate concrete (HSLWAC) using an agricultural solid waste, namely oil palm shell (OPS). This method is based on crushing large old OPS. Crushed OPS are hard and have a strong physical bond with hydrated cement paste. The 28 and 56 days compressive strength achieved in this study were about 53 and 56 MPa, respectively. Furthermore, it was observed that it was possible to produce grade 30 OPS concrete without the addition of any cementitious materials. Compared to previous studies, significantly lower cement content was used to produce this grade …

Influence Of Co2 Laser Radiation On The Mechanical Properties Of Portland Cement Pastes, Maria Del Rosario Moreno-Virgen, Juan José Soto-Bernal, José A. Ortíz-Lozano, Adrian Bonilla-Petriciolet, José Vega-Duran, Rosario González-Mota, José Pineda-Piñon

Adrian Bonilla-Petriciolet