Engineering Commons^™

Behavior Of Square And L-Shaped Slender Reinforced Concrete Columns Under Combined Biaxial Bending And Axial Compression, Wen Hu Tsao

Dissertations

A numerical analysis was developed to evaluate the complete load-deflection and moment-curvature relationships for square and L-shaped slender reinforced concrete columns subjected to biaxial bending and axial load. This computer model can be used for any cross section geometry and material properties of normal concrete. The analysis was based on a deformation control and both the ascending and descending branches of curves can be studied. The finite difference method was introduced to calculate the deflections which satisfy the compatibility equations. Six square slender columns and eight L-shaped slender columns were tested to compare their experimental load-deformation results with the analytical …

A Generalized, Parametric Pr-Qmf/Wavelet Transform Design Approach For Multiresolution Signal Decomposition, Hakan Caglar

Dissertations

This dissertation aims to emphasize the interrelations and the linkages of the theories of discrete-time filter banks and wavelet transforms. It is shown that the Binomial-QMF banks are identical to the interscale coefficients or filters of the compactly supported orthonormal wavelet transform bases proposed by Daubechies.

A generalized, parametric, smooth 2-band PR-QMF design approach based on Bernstein polynomial approximation is developed. It is found that the most regular compact support orthonormal wavelet filters, coiflet filters are only the special cases of the proposed filter bank design technique.

A new objective performance measure called Non-aliasing Energy Ratio(NER) is developed. Its merits …

The Hydraulic Performance Of A Vortex Tube Foector, F Mtaro

Tanzania Journal of Engineering and Technology (TJET)

The vorle.r tube silt exrrac/or consists of a pipe, rhe crest of which has a slit and lies flush across lhe canal bed.With minimal warer loss, I.oe bedload is extracted through lhe slil settling canal back ro the river, thus reducing or eliminating the bedload transported in main canal. Ihe resulting swirling flow phenomena is of complex nature and depends on sc conirol paramerers, as a result of which previous empirical design approaches have yielded conflicting guidelines. By means Of a simplified hydraulic system, the flow mechanism and energy in rhe can be determined.

Absorption Of Nitrogen Oxides Into Sodium Hydroxide Solution In A Packed Column: Effect Of Gas Flowrate And Temperature, J Katima

Tanzania Journal of Engineering and Technology (TJET)

The effect of gas flow rate and temperature on the absorption rate of nitrogen oxides (NO ) and column absorption eff iciency has been studied using a 2M goåium hydroxide (NaOH) solution in a packed The absorpt ion process was carried out at atmospheric column. pressure, with NOV concentration ranging between 150 and 10000 pp:tt, NO/N02 ratio of O and 1 iquid flow rate of O .8 1/ min. The gas flow rate was varied from 20 to 60 1/17 in and the temperature from 25 to 45 c. It was found that Ehe column absorption efficiency increases with decreasing …

Frictional Resistance Of Geotextiles, Md. Khairul Alam

Theses

The pullout resistance of geotextiles was examined using pullout tests. A suitable wooden box with large (2 ft x 2 ft x 4 ft) dimensions was used to avoid the effect of boundary and to simulate field conditions. Two types of failure patterns were observed. For shallow embedment (<3 ft), geotextile produced a movement of the surrounding mass of sand in the shape of an inverted cone due to interlocking friction between geotextile and sand particles. The cone angle decreases with increase in depth of embedment. For embedment equal to or greater than 3 ft., no sand cone developed and the failure occurred along the interface of geotextile and sand. For 1 ft. surcharge, the increase in the pullout resistance due to combined horizontal and vertical embedment was about 30 %.

An Implementation Of Bionomial-Qmf For Subband Coding Of Speech, Feng Chen

Theses

A real-time subband speech codec is implemented by the author on TMS320C25 digital signal processor based hardware for speech compression down to 0.25 bit per sample.

The Binomial Quadrature Mirror Filters (B-QMFs) are employed as the basic block for the hierarchical, dynamic tree, analysis/synthesis filter bank. After the analysis, available bits are optimally allocated among subbands. Band statistics are updated to overcome the nonstationarities of speech signal.

The energy compaction performance of this codec is compared with different subband and DCT in simulations for speech signals and AR(1) source models.

It is shown that the speech codec implemented provides an …

Computer Control For 2-Axis Magnetic Suspension System, Jian Chen

Theses

A two-axis magnetic suspension system. using linear-potentiometer position sensing and DC solenoids, controlled digitally by a 80386 microcomputer has been built and operated in our laboratory. Control algorithms obtained by combining the full-state feedback control law with two methods of estimating velocities are studied. One method uses a nonlinear reduced-order observer; the other uses a finite difference algorithm. The nonlinear reduced-order observer performs better in simulation but the difference algorithm takes less calculation time and is used in the implementation. The system has been operated successfully to suspend weights up to 1.2 lb. and to get a slant angle more …

Minimum-Time Control For Submarine Interception, Zaiping Chen

Theses

This thesis attempts to offer a possible improvement for conventional anti-submarine system which is mounted on warship. It consists of two parts: the control law and its realization concerning the particular problem. The control based on optimal theory is devised for three-dimentional minimum-time interception. A microprocessor system is also designed to achieve all necessary steps to track and attack the target. The thesis focuses on the question of how to launch a group of subcharges to destroy a submarine cruising under water: find the optimal trajectory by developing a numerical method to solve the nonlinear dynamic system and design a …

Influence Of Heavy Metal Concentration On Rotating Biological Contrator Performance, Huei-Sheng Cheng

Theses

Seven heavy metals ( Fe⁺², Mn⁺², Zn⁺², Ag⁺, Pb⁺², Cu⁺², Cd⁺² ) at various concentrations were investigated in a Rotating Biological Contactor (RBC) system. The experimental data indicated that the degree of heavy metal toxicity in the biological system mainly depended on the ratio of inflow heavy metal concentration to organic loading. The optimal ratio of heavy metal to organic loading was determined on the basis of the maximum removal of chemical oxygen demand (COD) under different operating conditions. In addition, the effect of heavy metal on …

Design And Development Of An Automated Assembly System In A Discrete Manufacturing Environment, Sandeep K. Desai

Theses

This work is dedicated to extend the technology of automated assembly to include small and thin parts, light in weight. As the parts are thin a problem exists in the feeding process and orientation. The objective of project is to overcome this difficulty. The main theme of this thesis is to reduce labor cost and to improve productivity and quality of assembly operations by introducing low cost automation in the companies having discrete manufacturing environment.

An example of assembly involving a thin part has been selected. Two components from an electrical switch assembly are chosen, namely the spring and rivet. …

Design Of An Advanced Control Algorithm For A Nuclear Power Plant Feedwater Control System, Randall C. Ezzo

Theses

Electric power companies with nuclear power plants have been aggressively looking for ways to increase plant safety and availability by increasing the reliability and performance of the plant's control systems. The performance of the Oyster Creek Nuclear Station's feedwater control system can be significantly improved by replacing the proportional-integral compensator with a compensator based on modern control concepts. In response to a -10 inch reactor water level setpoint change, settling time is improved from 107 seconds with 3% overshoot to 34 seconds with no overshoot.

A Case Study On Petri Net Modeling, Animation, And Simulation, Suresh C. Gurala

Theses

Petri nets as a graphical tool has developed over the last decade into a suitable model for representing, modeling, designing, analyzing and studying concurrent systems. In this thesis, Petri nets are applied for analyzing, modeling and simulation of a flexible assembly station. An existing AT&T FWS200 flexible assembly workstation for printed circuit board is modeled using Petri nets without the consideration of insertion failures and other abnormalities in the system. The Petri net model is then simulated using Graphics simulation language (GSL).

Advanced Manufacturing Applications Of Cost Estimating Techniques For Metal Cutting Industries, Zubair Hamid

Theses

In this work, different cost estimating techniques in metal cutting industry were studied. A basic understanding of estimation concepts were given. The typical breakdown of total cost was also given and discussed in details. Practical applications of cost estimating is studied. The effect of different parameters which relate to the lot sizes or quantity were discussed. All these results show that total cost is minimum at a point which is called least cost point, after that cost increases because of the addition of extra resources, in terms of man, machine and increase in administrative expenses.

Bridge Deterioration Models, Christopher R.H. Howard

Theses

The deteriorated condition of America's bridges raises the need for a proper and optimal method of bridge management, from the conceptual stage through the construction stage, and throughout the useful life of our bridges. State agencies need to expand their data collection process so as to include additional information pertinent to the formulation of a credible system. This is critical in order to accommodate increased research efforts to investigate the behavioral pattern/s of the nations bridges and to eventually optimize bridge management systems. This thesis looks at the bridge deterioration model as a vital tool in realizing more effective bridge …

Liquid-Liquid Dispersion In Agitated Vessels Provided With Multiple Impellers, Yu-Tsang Huang

Theses

Baffled vessels with multiple impellers are widely used in industry to generate liquid-liquid dispersions. In this work, a new method to determine the minimum agitation speed for complete dispersion in two immiscible liquids was developed. This method was conceived to replace the traditional visual observation method that has been extensively used in the past for this purpose. The minimum agitation speeds for liquid-liquid dispersion with single and multiple impellers in baffled vessel were also measured. The effect of a number of variables such as size and type of impellers, size of tank, impeller location, spacing between impellers, and dispersed phase …

Fast Arithmetic Operations On The Hypercube Using Conditional Sum Addition And Modified Booth's Algorithm, Umar Bin Iftikhar

Theses

Algorithms for fast arithmetic operations (i.e., addition and multiplication) on the hypercube computer are presented. The hypercube network of dimension d interconnects N = 2^d processors in such a way that each processor is directly connected to d neighboring processors; m order to communicate between processors, the maximum length of the path is d. The addition algorithm is based on the conditional sum technique. The computational time using this algorithm is O(log₂ N+q) where q is the number of the bits per processor in the hypercube of N processors. Operands of size N*q are distributed among the hypercube …

Development Of An Expert System For The Safety Of Workers From Electrical Hazards At Work Place, Faizul Islam

Theses

This thesis presents the development of an expert system for the safety of workers from electrical hazards at work place.

The objective of this work is to show how an expert system within the workplace can be used in helping to create an effective safety program.

An effective expert system for electrical safety have been developed for the workers to prevent accidents from electrical hazards using the safety regulations of Occupational Safety and Health Administration.

The regulations developed by OSHA have been incorporated in rule based expert system which can be accessed by any non computer professional and the system …

Response Characteristics Of Inelastic Single Degree Of Freedom Systems Subjected To Intraplate Earthquakes, Linda C. Jones

Theses

Within recorded, although not recent, history, there have been several large magnitude earthquakes in the Eastern and Central United States and the need to provide measures to protect from potential damage is recognized by the engineering community. Since there are inherent differences between earthquakes that occur along tectonic plate boundaries, interplate, and those that occur within the plate boundaries, intraplate, it is important to understand how these differences impact structural design. A parametric study of single degree of freedom systems subjected to various recorded and artificial ground motions was performed to identify the variations in response characteristics.

It was found …

Stability And Durability Of Large Aggregate Asphalt Concrete, Rais A. Khan

Theses

There are many factors which affect the properties of asphalt concrete and one of these is a maximum aggregate size used in the mix. In this study of the effect of maximum aggregate size on Marshall stability, flow and durability of asphalt aggregate mixtures is investigated.

Two different mixes having gradations with maximum aggregate sizes of 3/4 and 1-1/2 inches were considered. The optimum asphalt content for mix having 3/4 inch maximum aggregate size, was determined by the standard Marshall procedure. The optimum asphalt content for the mix having 1-1/2 inch maximum aggregate size, was estimated based on thickness of …

Vision-Guided Servoing Robot Arm System, Shing Lee

Theses

This thesis investigate the problem of tracking 2-D circle parts with an eye-in-hand robot arm system. A vision module capable of measuring the motion of a circle is developed. Two algorithms based on the conic equation representation of circle and the symmetric property are developed. The first algorithm approximates the image of the circle as an ellipse. The second algorithm use the arc radius estimator to extract two image points of the circle located at the center of the largest arc. These image points are then used to solve for the inverse perspective transformation. An inverse kinematics solution based on …

Development Of Cellular Manufacturing Systems For Overall Production Efficiency, Srinivas Lokula

Theses

For years the industrial job shop is facing an increase in complexity and decline in productivity due to increase in parts mix, volume of parts, plant size, machine production rates and part complexity. The development of Group Technology and Cellular Manufacturing seeks to eliminate or minimize complexity and to maximize productivity.

Cellular manufacturing is the physical division of job shop's manufacturing machinery into production cells. Each cell is designed to produce parts requiring similar machinery and machine operations. Cellular manufacturing is one of the best manufacturing techniques to support Just In Time manufacturing and Total Quality Management.

This thesis work …

Biodegradation Of Tnt (2,4,6-Trinitrotoluene), Jin Lou

Theses

This study summaries the results of various methods treating 2,4,6-trinitrotoluene (TNT). Review of available literatures revealed that the most commonly used techniques in full-scale plant for TNT removal are chemical oxidation and carbon adsorption.

From economic point of view, the biological treatment system will be much more cost-effective. Various methods for improving the efficiency of biological system treating TNT wastewater were developed in the laboratory. Current laboratory results show that by isolating appropriate microorganisms under adequate conditions, TNT wastes can be degraded successfully.

At the some time, some pretreatment technologies are recommended in this study for improving the performance of …

Design For Manufacturability (Computer Aided Optimum Gear Design), Narayan R. Mareddy

Theses

Design for manufacturing has design as the first manufacturing step. It is important to recognize the importance of design clubing with manufacturing to reduce the production, set up time. In this thesis concepts of design, manufacturing and four different ways of bringing design and manufacturing together are discussed in detail.

As there are large number of variables in the gear rating equations, it is very difficult to achieve optimum design by manual methods unless an extensive trial and error process is carried out. An algorithm has been developed which allows rapid convergence to the optimum gear design. The algorithm has …

Computer Aided Design Of A Broadband Microwave Power Divider, Jaideep Mukherjee

Theses

The purpose of this thesis to provide alternative design procedure for a power divider that has broadband characteristics. The Wilkinson power divider consisting of cascaded quarter wave sections is known to increase the bandwidth while maintaining high isolation and good match conditions at individual ports. Resistors placed between the quarter wave sections served to increase isolation. The values of required components were determined using odd and even mode analysis. In this work, the approximate theory developed previously is used as a preliminary design model, and it is extended further by considering optimization techniques and coupling between adjacent arms. This novel …

Studying The Mechanical Response Of Outer Hair Cells To Electric Pulses Using Image Sensors, Wayel F. Mutlag

Theses

The purpose of this research was to develop a way to improve the method used by Dr. Santos-Sacchi at the University of Medicine and Dentistry of New Jersey to detect the motion of the outer hair cell (OHC). As part of the work, the construction and functioning of the OHC are presented and two designs to detect the motion of the boundary of the OHC were investigated.

The first design utilizes the position sensitive detector (PSD) S3932 made by Hamamatsu Inc. This detector, however, required excessive intensity of the optical signal that was not compatible with the operation of the …

Handling Of Glass Mat Thermoplastic From Manufacturing Station To Heating Station To Molding Machine, Ramulu Srinivas Neela

Theses

GMT composite sheets are a family of continuous glass fiber roving impregnated with thermoplastic resin with parts formed by compression molding. Significance of GMT sheets comes by its cost-effective performance sufficient to penetrate automotive, industrial, construction, and other markets not willing to pay for higher cost, fiber-reinforced composite systems. GMTs in comparison to traditional sheet metals and sheet molding compounds (SMCs) are lighter, corrosion resistant, require no special storage, exhibit faster cycle times, require no chemical reaction, produce less scrap, possess recycling benefits, are ready for painting, and exhibit maximum opportunities for parts consolidation due to exceptional strength, formability, lower …

Study Of A Non-Contact Gaging System Of Inspection, Gordhanbhai Ketan Patel

Theses

The quality control function has traditionally been performed using manual inspection methods and statistical sampling procedures. Manual inspection is generally a time - consuming procedure which involves precise, yet monotonous work. It often requires that parts be removed from the vicinity of the production machines to a separate inspection area. This causes delays and often constitutes a bottleneck in the manufacturing schedule.

As a solution to the above problem a Non - Contact Gaging System developed by Optical Gaging Products, Inc., has been used here to study the feasibility of using an automated inspection system and a procedure of developing …

Realization Of High-Speed Carry Propagation For Addition And Multiplication Using The Redundant Binary System On The Mesh And Hypercube Connected Structures, Anil Rana

Theses

The extensive development of large-scale digital computers has naturally been accompanied by a corresponding development of techniques for fast arithmetic operations. Addition is the basis for the majority of the other arithmetic operations and most of the required time is due to carry propagation delay. Various algorithms have been proposed for fast addition and multiplication. The algorithms proposed here use the redundant binary system and are designed for the mesh structure. The algorithms are very efficient for the addition and multiplication of long operands. The algorithms can also be implemented on the hypercube. The n-dimensional hypercube is a highly concurrent …

Implementing Computer Numerical Control Machine Tools In A Job Shop Environment, Rajesh Shah

Theses

Computer Numerical Control is one important phase to overall application of computer on the shopfloor. Today a large variety of CNC machine tools are offered by manufacturer following different standards. This thesis is organized with the purpose of comparing various technical and economical considerations for CNC machine tool purchase and application. The main purpose of study is to mention various features of CNC machine tools and its possible integration which can reduce product lead time and improve quality. General replacement minimum cost model is discussed with case study for economic justification of machine purchase. While discussing technical features emphasis is …

Strength And Fragility Of Concrete, Kang-Qun Shao

Theses

It is known that both strength and fragility are two of the most important properties in concrete. In this research, theories of Chemistry, Physical Chemistry of Surfaces, Thermodynamics and Fracture Mechanics are used to study the relationships between the macromechanical behavior of concrete and the microstructure in concrete. The objectives of this research are therefore to find some effective ways to explain theoretically why the concrete is so brittle (fragile) and how to increase its strength or to decrease its fragility. Based on the present studies, an equation is formulated to calculate the coefficient of the fragility (or brittleness) of …