Engineering Commons^™

Reverse Decision Making And Goal Attainment A Proof Of Concept As A New Approach To The Decision Making Process Under Uncertainty, Shitalkumar S. Sabne

Engineering Management & Systems Engineering Theses & Dissertations

Decision making occurs when one must choose among alternatives. However, in uncertain environments where problems are complex and decision makers lack complete knowledge of the situation as well as decision alternatives, it's not possible for them to select an optimal decision outcome by 'Traditional Decision Approaches'. At present Reverse Decision Making is the central, although new and unproved, approach of Old Dominion University's Engineering Management and Systems Engineering research on decision making process for uncertain and complex situations. Even though research in decision making spans over one hundred years, there are still important problems which remain to be addressed.

There …

An Empirical Investigation Into The Relationships Between Emotional Intelligence, Use Of Knowledge Transfer Methods, And Project Performance, Brent Michael Decker

Engineering Management & Systems Engineering Theses & Dissertations

Increasingly, the use of project teams is becoming commonplace within organizations as the primary means to accomplish complex tasks. While the literature has long acknowledged that the knowledge transfer process is a key component in achieving organizational success and ultimately sustaining a competitive advantage, very little has been written that specifically examines the knowledge transfer process at the project team level. In an attempt to increase the understanding of knowledge transfer processes at the project team level, the effect that a relatively new construct, termed emotional intelligence, has on the use of knowledge transfer methods is examined. The relationships between …

Learning As A Nonlinear Line Of Attraction For Pattern Association, Classification And Recognition, Ming-Jung Seow

Electrical & Computer Engineering Theses & Dissertations

Development of a mathematical model for learning a nonlinear line of attraction is presented in this dissertation, in contrast to the conventional recurrent neural network model in which the memory is stored in an attractive fixed point at discrete location in state space. A nonlinear line of attraction is the encapsulation of attractive fixed points scattered in state space as an attractive nonlinear line, describing patterns with similar characteristics as a family of patterns.

It is usually of prime imperative to guarantee the convergence of the dynamics of the recurrent network for associative learning and recall. We propose to alter …

Performance Analysis Of Recoverable Flight Control Systems Subject To Neutron-Induced Upsets Using Hybrid Dynamical Models, Hong Zhang

Electrical & Computer Engineering Theses & Dissertations

It has been observed that atmospheric neutrons can produce single-event upsets in digital flight control hardware. Potentially, they can reduce system performance and introduce a safety hazard. One experimental system-level approach investigated to help mitigate the effects of these upsets is NASA Langley's Recoverable Computer System. It employs rollback error recovery using dual-lock-step processors together with new fault tolerant architectures and communication subsystems.

In this dissertation, a class of stochastic hybrid dynamical models, which consists of a jump-linear system and a stochastic finite-state automaton, is used to describe the performance of a Boeing 737 aircraft system in closed-loop with a …

High Performance Queueing And Scheduling In Support Of Multicasting In Input-Queued Switches, Weiying Zhu

Electrical & Computer Engineering Theses & Dissertations

Due to its mild requirement on the bandwidth of switching fabric and internal memory, the input-queued architecture is a practical solution for today's very high-speed switches. One of the notoriously difficult problems in the design of input-queued switches with very high link rates is the high performance queueing and scheduling of multicast traffic. This dissertation focuses on proposing novel solutions for this problem. The design challenge stems from the nature of multicast traffic, i.e., a multicast packet typically has multiple destinations. On the one hand, this nature makes queueing and scheduling of multicast traffic much more difficult than that of …

Micron-Level Actuator For Thermal-Fluid Control In Microchannels, Nurhak Erbas

Mechanical & Aerospace Engineering Theses & Dissertations

Effectiveness of an actuator is investigated for thermal-flow control in microchannels. First, simulations of a single actuator in a quiescent external medium are performed in order to study the parameters characterizing the synthetic jet flow from the actuator. For this purpose, a simplified, two-dimensional configuration is considered. The membrane motion is modeled in a realistic manner as a moving boundary in order to accurately compute the flow inside the actuator cavity. The geometric and actuation parameters of the actuator are investigated to define the effectiveness of the jet flow. The study is done initially at macro scales. Then, the flow …

An Adaptive Algorithm To Identify Ambiguous Prostate Capsule Boundary Lines For Three-Dimensional Reconstruction And Quantitation, Rania Yousry Hussein

Electrical & Computer Engineering Theses & Dissertations

Currently there are few parameters that are used to compare the efficiency of different methods of cancerous prostate surgical removal. An accurate assessment of the percentage and depth of extra-capsular soft tissue removed with the prostate by the various surgical techniques can help surgeons determine the appropriateness of surgical approaches. Additionally, an objective assessment can allow a particular surgeon to compare individual performance against a standard. In order to facilitate 3D reconstruction and objective analysis and thus provide more accurate quantitation results when analyzing specimens, it is essential to automatically identify the capsule line that separates the prostate gland tissue …

Development Of A Theoretical Framework Of Distributed Cognition Phenomena In Control Centers During Crisis Conditions, Christopher J. West

Engineering Management & Systems Engineering Theses & Dissertations

The purpose of this research is to develop and partially validate a theoretical framework describing distributed cognition phenomena occurring in organizational control centers functioning in crisis environments. Using a systems approach, the work synthesizes existing constructs relating to distributed cognition then supplements this knowledge with review of crisis management literature. The goal of this effort is the development of a framework for understanding the impact of crisis conditions on such phenomena occurring within the specified setting. An exploratory case study approach was used to partially validate and refine the framework by gauging its ability to interpret the impact of crisis …

Boundary Interference Assessment And Correction For Open Jet Wind Tunnels Using Panel Methods, Wael Ahmed Mokhtar

Mechanical & Aerospace Engineering Theses & Dissertations

The presence of nearby boundaries in a wind tunnel can lead to aerodynamic measurements on a model in the wind tunnel that differ from those that would be made when the boundaries of the moving fluid were infinitely far away. The differences, referred to as boundary interference or wall interference, can be quite large, such as when testing aircraft models developing high lift forces, or whose wingspan is a large fraction of the wind tunnel width, or high drag models whose frontal area is a large fraction of the tunnel cross section. Correction techniques for closed test section (solid walled) …

Mechanical Properties And Durability Of A Composite Material At Cryogenic Temperatures, Ray Walton Grenoble

Mechanical & Aerospace Engineering Theses & Dissertations

Several issues relevant to the use of a high-performance graphite-epoxy material in hydrogen storage tank applications have been examined. The tensile properties of IM7/977-2 were evaluated as a function of test temperature and thermal-mechanical load history. The temperature dependent coefficient of thermal expansion (CTE) of unidirectional specimens of the same material was measured between -200°C and 0°C. The effects of test temperature, mechanical loading, and damage state on the leak rate of hydrogen gas through IM7/977-2 laminates were evaluated using a novel test system. Finally, the mechanical properties of several commercially available polymer films, which might prove useful as leak-resistant …

Whole Word Phonetic Displays For Speech Articulation Training, Fansheng Meng

Electrical & Computer Engineering Theses & Dissertations

The main objective of this dissertation is to investigate and develop speech recognition technologies for speech training for people with hearing impairments. During the course of this work, a computer aided speech training system for articulation speech training was also designed and implemented. The speech training system places emphasis on displays to improve children's pronunciation of isolated Consonant-Vowel-Consonant (CVC) words, with displays at both the phonetic level and whole word level. This dissertation presents two hybrid methods for combining Hidden Markov Models (HMMs) and Neural Networks (NNs) for speech recognition. The first method uses NN outputs as posterior probability estimators …

Atmospheric-Pressure Plasma Sources For Polymer Surface Modification, Shujun Yang

Electrical & Computer Engineering Theses & Dissertations

Plasma processing is widely used in the microelectronics industry for deposition of thin films. It is also used in etching of semiconductors, metals and organic materials such as photoresists. In addition, plasmas are widely used to modify material surfaces. Plasma surface modification can improve the surface adhesion of polymeric materials, which can be used as insulating layers in multilayer semiconductor structures. In deposition and etching, relatively a large amount of material is added to or removed from the surface. In plasma surface modification, only the surface layer is changed in composition or structure, and no significant amount of material is …

A Comparative Analysis Of Air-To-Ground Engagement Outcomes In The Joint Warfare System (Jwars) And The Jwars-Joint Semi-Automated Forces Federation, Melissa Anne St. Peter

Computational Modeling & Simulation Engineering Theses & Dissertations

Multi-resolution modeling is the process by which a single model is created by connecting multiple individual models to describe phenomena at different levels of resolution [1]. "When we change resolutions, replacing a detailed model by a more aggregate one, we must ask whether results are 'consistent'" [2].

There are many methods of determining if the results of two simulations are 'consistent'. However, they are very entailed and require a detailed understanding of the individual models including their functionality, algorithms, and inner workings. A straight forward and rapid way of assessing potential inconsistencies is through a statistical comparison of the model …

Passive And Active Nonlinear Control Of Ship Roll Motions Using U-Tube Tanks, Thongchai Phairoh

Mechanical & Aerospace Engineering Theses & Dissertations

A U-tube water tank is first designed to roll a ship floating on still water. The 6-degree of freedom (DOF) dynamic model of U-tube tank is derived and the effects of its parameters on ship roll motion are studied. Numerical simulations show that the U-tube tank is an effective stimulator to roll the ship on still water. For a rolling ship, the U-tube tank can be used as a damper to reduce ship roll motion quickly.

Active control of ship roll motion with a proportional and derivative (PD) controller, linear quadratic regulator (LQR), generalized predictive control (GPC), and deadbeat predictive …

An Analysis Of Indicator Organism Suitability For Lower James And York Rivers, Rhonda Ashonti Ford

Civil & Environmental Engineering Theses & Dissertations

The primary objectives of this thesis are (1) determine if the proper indicator organism is being utilized to determine the bacterial water quality in the State of Virginia. (2) If other environmental factors can predict the bacterial water quality. The current indicator organism of choice for bacterial water quality of waters in the State of Virginia is enterococci, for estuarine and brackish waters. E. coli is the indicator organism of choice for fresh waters in Virginia.

The study concluded (1) Enterococci are the best indicator organism for beaches located in the Hampton Roads Harbor and the Lower James River. (2) …

Improving Efficiency In Engineering Design Using Augmented D-Optimal Designs 'Synthetic Jet' Design Optimization Study, Fatih Erdogan

Engineering Management & Systems Engineering Theses & Dissertations

The purpose of this thesis is to study the efficiency of several "design of experiments" (DOE) approaches used for the analysis and optimization of engineering designs. A literature review is conducted to study various "design of experiments" methods and the advantages and limitations of each method are discussed.

As an application, Augmented D-Optimal designs are utilized for a design study of 'synthetic jet'.

With the objective of improving efficiency and providing a minimum point experimental design model, computer-aided D-optimal method is preferred for this study. For setting up the design of the experiments and for performing the analysis of results, …

Crisis Management In Projects, Senol Nazikkol

Engineering Management & Systems Engineering Theses & Dissertations

The objective of this investigation is to identify the processes, benefits and important tools of crisis management in projects. Crisis management is a system that helps managers to prevent and overcome crises. In this research, a general review about crisis, crisis management processes and tools are discussed. The research was done by using the information in the literature and expert judgment. This paper can be used by academics as a foundation for further research and development in the area of crisis management in projects. Managers of projects can use this study for improving their projects and project-based organizations' crisis management …

Robustness And Control Of A Magnetically Levitated Transportation System, Grzegorz Oleszczuk

Mechanical & Aerospace Engineering Theses & Dissertations

Electromagnetic suspension of Magnetic Levitation Vehicles (Maglev) has been studied for many years as an alternative to wheel-on rail transportation systems. In this work, design and implementation of control systems for a Maglev laboratory experiment and a Maglev vehicle under development at Old Dominion University are described. Both plants are modeled and simulated with consideration of issues associated with system non-linearity, structural flexibility and electromagnetic force modeling. Discussion concerning different control strategies, namely centralized and decentralized approaches are compared and contrasted in this work. Different types of electromagnetic non-linearities are considered and described to establish a convenient method for modeling …

Stability Analysis Of Hybrid Jump Linear Systems With Markov Inputs, Arturo Tejada Ruiz

Electrical & Computer Engineering Theses & Dissertations

In the past two decades, the number of applications that make use of supervisory algorithms to control complex continuous-time or discrete-time systems has increased steadily. Typical examples include air traffic management, digital control systems over networks, and flexible manufacturing systems. A common feature of these applications is the intermixing of the continuous dynamics of the controlled plant with the logical and discrete dynamics of the supervising algorithms. These so-called hybrid systems are the focus of much ongoing research. To improve the performance of these systems, it is important to analyze the interactions between the supervising algorithms and the plant. Few …

Diverse Effects Of Nanosecond Pulsed Electric Fields On Mammalian Cells, Jody Anne White

Theses and Dissertations in Biomedical Sciences

The continuing effort to manipulate cell-signaling pathways for therapeutic benefit has lead to the exploration of electric field effects on cells. Current electric field applications include electroporation of the plasma membrane for introduction of drugs, genes, or other macromolecules into cells. Modeling of how these pulsed electric fields affect cells depicts the cell as an excitable circuit. In this model, the electric fields, administered in short pulses to a cell, charge the plasma and internal membranes, which act as dielectric layers, and between these the cytoplasm acts as a conductive medium. The pulse lengths of this treatment are traditionally in …

A Dyadic Composition To Foster Virtual Team Effectiveness: An Experimental Study, Gamze Karayaz

Engineering Management & Systems Engineering Theses & Dissertations

The importance of effectiveness for virtual teamwork continues to gain momentum as technology and globalization of work accelerate. The implementation of virtual teams provides one approach to enhance competitiveness, overcoming the disadvantages of space and time differences through collaborative technologies. The influence of structure to virtual team performance has not been clearly established in the literature. The purpose of this research study was to investigate the effectiveness of a dyad structured approach for virtual teams using a quasi-experimental research design.

This research investigated four questions related to the influence of structure on virtual team effectiveness related to task performance, communication …

Automatic Speech Recognition Using Lp-Dctc/Dcs Analysis Followed By Morphological Filtering, Penny Hix

Electrical & Computer Engineering Theses & Dissertations

Front-end feature extraction techniques have long been a critical component in Automatic Speech Recognition (ASR). Nonlinear filtering techniques are becoming increasingly important in this application, and are often better than linear filters at removing noise without distorting speech features. However, design and analysis of nonlinear filters are more difficult than for linear filters. Mathematical morphology, which creates filters based on shape and size characteristics, is a design structure for nonlinear filters. These filters are limited to minimum and maximum operations that introduce a deterministic bias into filtered signals.

This work develops filtering structures based on a mathematical morphology that utilizes …

Development Of A Nonlinear Estimator-Based Model Of Pilot Performance During Brownout Conditions, Karl Ulrich Schultz

Mechanical & Aerospace Engineering Theses & Dissertations

During conditions of visual occlusion, pilots are forced to rapidly adapt their scan to accommodate the new observable states via instruments rather than the visual environment. During this transition, the provision of aircraft state information via other than visual modalities improves pilot performance presumably through the increase in situational awareness provided immediately following the visual occlusion event.

The Tactile Situational Awareness System (TSAS) was developed to provide continuous position information to the pilot via tactile rather than visual means. However, as a low-resolution display, significant preprocessing of information is required to maximize utility of this new technology.

Development of a …

Processing And Characterization Of High Performance Structural Nanocomposites, Dennis C. Working

Mechanical & Aerospace Engineering Theses & Dissertations

Carbon nanotubes are considered to be a revolutionary material breakthrough due to their unique combination of properties. While many applications for SWCNTs have been projected, realization of these potential uses have been hampered by the high cost of limited supplies of high quality SWCNTs and the difficulty in the development of a suitable processing method that does not damage the filler thus diminishing the desirable properties of this material. In spite of these technical challenges, their potential to enable the fabrication of multifunctional materials is being investigated in earnest. The goal of this thesis is to investigate the feasibility of …

A Robust Reactive Scheduling System With Application To Parallel Machine Scheduling, Jean-Paul M. Arnaout

Engineering Management & Systems Engineering Theses & Dissertations

In this turbulent world, scheduling role has become crucial in most manufacturing production, and service systems. It allows the allocation of limited resources to activities with the objective of optimizing one performance measure or more. Resources may be machines in a factory, operating rooms in a hospital, or employees in a company, while activities can be jobs in a manufacturing plant, surgeries in a hospital, or paper work in a company. The goal of each schedule is to optimize some performance measures, which could be the minimization of the schedule makespan, the jobs' completion times, jobs' earliness and tardiness, among …

Assimilating Non-Probabilistic Assessments Of The Estimation Of Uncertainty Bias In Expert Judgment Elicitation Using An Evidence Based Approach In High Consequence Conceptual Designs, Colin K. S. Barrows

Engineering Management & Systems Engineering Theses & Dissertations

One of the major challenges in conceptual designs of complex systems is the identification of uncertainty embedded in the information due to lack of historic data. This becomes of increased concern especially in high-risk industries. This document reports a developed methodology that allows for the cognitive bias, estimation of uncertainty, to be elucidated to improve the quality of elicited data. It consists of a comprehensive literature review that begins by defining a 'High Consequence Conceptual Engineering Environment' and identifies the high-risk industries in which these environments are found. It proceeds with a discussion that differentiates risk and uncertainty in decision-making …

Femtosecond Laser Ablation With Single And Two-Photon Excitation For Mems, Mohamed Abdelfattah Kottb Ahmad Elbandrawy

Electrical & Computer Engineering Theses & Dissertations

There is an increasing interest in femtosecond laser micromachining of materials because of the femtosecond laser's unique high peak power, ultrashort pulse width, negligible heat conductivity process during the laser pulse, and the minimal heat affected zone, which is in the same order of magnitude of the ablated submicron spot. There are some obstacles in reaching optimal and reliable micromachining parameters. One of these obstacles is the lack of understanding of the nature of the interaction and related physical processes. These processes include amorphization, melting, re-crystallization, nucleated-vaporization, and ablation.

The focus of this Dissertation was to study the laser-matter interaction …