Engineering Commons^™

Mechanical Properties And Corrosion Resistance Of Ni-Sic Nano Composite Coatings On 2024-T3 Aluminum, Amit Jain

Masters Theses

Coatings of nickel with and without silicon carbide nano-particles were carried out on 2024-T3 aluminum alloy by the electrochemical process. The size of the silicon carbide particles was less than 50nm. Nickel coatings were done using a nickel sulfamate bath maintained at a constant temperature of 50° ± 5° C. Tensile specimens were prepared and studied to determine the Young's modulus of bare aluminum, with nickel coatings and with composite nickel and silicon carbide coatings. Wear samples of 1 inch² (6.45cm²) were prepared and studied for wear resistance. The residual stress measurements were done by the hole …

The Effect Of Non-Stoichiometry On The Structure Of La-Ni And La-Ni-Ga Alloys, Pertrice Auguste Wethey

Masters Theses

Non-stoichiometric samples of the AB₅ system defined by the formula La_1-yNi_5+2y and LaNi_5+2xGa_1-x were cast using an arc-melting furnace. The samples were then analyzed to determine their lattice parameters and phases present using XRD. They were then heat-treated to produce homogeneous compounds and quenched with the intention of retaining high temperature compositions. Following the heat-treatment, the alloys underwent XRD again as well as SEM/EDS. The XRD information was analyzed using Rietveld refinement and the elemental data derived from the EDS was used to ascertain the compositions were statistically akin to the weighed values. …

Hot Melt Inks For Rotogravure-Formulation, Printability And Rheology, Hrishikesh Shreeram Bhide

Masters Theses

A new generation of "Hot melt inks for Rotogravure" was formulated. They melt during heating and reach printable viscosity between 75° C and 130° C, depending on formulation. After printing onto substrate, they solidify. Selections of the best formulations were done based on ink rheology, and print analysis. The formulated inks were also printed on the Moser sheet-fed proofing press .. The rheological data indicated that hot melt inks (without viscosity modifier) have viscosity in the range of 10°-10¹ Poise at 95°C. After printed on a laboratory gravure K-Proofer, the inks showed good reflective density (0.90 - Yellow, 1.30 …

Innovative Contracting Prequalification/Selecion Model Using Analytical Hierarchy Process (Ahp), Saad J. Zidan

Masters Theses

Design-Build, Cost-Plus-Time, and warranty are the three innovative contracting methods that the Federal Highway Administration (FHWA) decided to fund. FHWA allowed the usage of these methods in federally funded projects if this will result in reducing time, improving quality, and saving tax payers' money. Prequalification is recognized as the best way of assuring that contractors do have the required qualifications to deliver projects successfully. Prequalification is even more critical when low-bid selection method is used with any of the innovative contracting, since incompetent contractors may get awarded for low-bids that are not based on valid assumptions.

This study presents a …

Color Management Of Desktop Input Devices: Quantitative Analysis Of Profile Quality, Xiaoying Rong

Masters Theses

This thesis investigates the color management principle and input device profiling. The input devices discussed in this thesis are flatbed scanners.

In this thesis, the human visual system, CIE L*a*b* color space, ICC profiles are reviewed, and the evaluation of profile quality is discussed. Grayscale and standard color targets of three primary suppliers are used to create profiles for a scanner. The quantitative analyses of the quality of different profiles, created by two primary commercial profiling software, are conducted according to the Delta-E of the CIE L*a*b* color space. Finally, the relationship of different color targets and profiles for desktop …

Investigation Of Electrical Properties And Structure Of Vacuum Evaporated C60 Films, Angiras D. Pandya

Masters Theses

C₆₀ is an important electronic material and its properties can be tuned by thermal annealing process and solid phase crystallization process. These properties were investigated as a function of thermal annealing temperature and solid phase crystallization. However there is no systematical study on annealing effect and Solid Phase Crystallization of C₆₀ films. In this study, the effect of thermal annealing on formation of nanocrystalline C₆₀ thin films were investigated for annealed samples and solid phase crystallized samples. The C₆₀ films described here were prepared by vacuum thermal evaporation method. The structural properties of C₆₀ films …

Effects Of Sodium Metaborate On Kraft Pulping, Biljana M. Bujanovic

Dissertations

The kraft lime cycle can be either replaced or supplemented by borate-based autocausticizing (total or partial autocausticizing, respectively). The borate-based autocausticizing uses sodium metaborate to produce sodium hydroxide in the two-step reaction performed in a recovery boiler and dissolving tank. In accordance with the borate-based autocausticizing chemistry, sodium metaborate is an additional chemical in both pulping and recovery. The studies of kraft pulping in the presence of sodium metaborate provide insight into the effect which sodium metaborate might have on the pulping process including the delignification rate, selectivity of lignin removal, and the properties of both pulp and black liquor. …

Psychophysically Derived Work Frequencies Associated With Roof Shingling Operations Involving Change In Grade, Sang Dae Choi

Dissertations

The objective of this study was to investigate the effect of roof slope on psychophysical roof shingling frequency. Twelve healthy males (21-30 years old) were used as participants. Experiment one was designed to determine Maximum Acceptable Roof Shingling Frequency (MARSF) for a workday period using psychophysical methodology. Results indicate that 198 shingles/hr is an acceptable roof shingling frequency for a workday. Furthermore, 2 hours is an acceptable testing period (equivalent to the workday). Postural sway and physiological variables support these findings. Experiment two was designed to study the effect of slope (18°, 26°, and 34°) on MARSF. Experiment two indicates …

Evaluation Of The Distribution Of Taguchi's Signal-To-Noise Ratio And The Effectiveness Of The Signal-To-Noise Ratio For Detecting Changes In The Mean And/Or Variance, Jinsuk Lee

Masters Theses

The concept of parameter design developed by Taguchi to achieve robust engineering is widely promoted in industry as a means to design a product whose output is largely immune to noise in the system. Taguchi has used the signal-to-noise (S/N) ratio to summarize measures over the noise factor settings at the parameter design and to allow control of the experiment.

The objectives of this investigation are: 1) to infer distributions of S/N ratios (lower-the-better S/N, higher-the-better S/N, and nominal-the-best SIN), and 2) to determine the effectiveness of the S/N ratio as a means for identifying changes in the mean and …

Effect Of Modified Clay-Zeolite Pigment On The Viscoelastic, Optical, And Printing Properties Of A Lwc Gravure Coating, Lokendra Pal

Masters Theses

This study investigates the influence of modified clay- zeolite pigment on the viscoelastic, optical, and printing properties of a LWC coating. Currently, lightweight, coated papers have experienced problems with mottle, distortion, fiber puffing and poor print quality when printed with water-based inks. However, water-based inks represent a proven solution to reducing volatile organic compound (VOCs) emissions. Poor wetting and ink spreading on the paper surface constitute the majority of print quality issues associated with the water-based printing of LWC papers.

Similar problems are encountered during the printing of ink jet papers due to high percentage of water contained in these …

Parallel Simulation Of Microflows By Dsmc And Burnett Equations, Yichuan Fang

Dissertations

The primary objective of this dissertation is to numerically simulate and study the heat transfer and flow characteristics in fluidic microelectromechanical system (MEMS). In typical microfluidic MEMS applications, the ratio of the gas mean-free-path to the characteristic length scale, or the Knudsen number, can be large. The traditional mathematical models of continuum fluid based on the Navier-Stokes equations may become invalid because of their constitutive relations of viscous stress and heat flux.

In this study, the direct simulation Monte Carlo (DSMC) method and the conventional Burnett equations are applied to model the microflows in microchannels from molecular and continuum point …

Investigation Of The Iced Flowfield Characteristics Related To The Stall Margin Instrumentation Used In Icing Conditions, Erik Pederson

Dissertations

The purpose of this dissertation is to investigate the relationship between the flowfield surrounding an iced airfoil and the stall margin instrumentation developed for use in icing conditions. The stall margin system indicates to the pilot the change in available lift due to ice accretions on the leading edge of an airfoil. This system displays the change in the form of a normalized lift coefficient. Four pressure ports are chosen to specifically maintain a constant calibration curve, for pressure versus normalized lift coefficient, regardless of ice shape. This allows these pressures to be used to determine the change in maximum …

Future Housing In The United States: Senior’S Housing Demand, Sandeep Singh

Masters Theses

In the United States, persons born between 1942 and 1964 are within 10 to 15 years of traditional retirement age and are identified as baby boomers. The data shows that the number of persons aged 65 years and older have grown from 10 percent of the population in 1970 to nearly 13 percent in 1996. Furthermore, the population that is 65 years old or older is projected to be 20 percent of the population in 2030. As a result, the demographic change nurtures a demand for senior’s housing.

On the other hand, the concern is for the elderly living in …

Development Of A Redesign Plan For Moore Hall Using Architectural Principles Of Green Building And Sustainable Design, Alkhaziam Saad

Masters Theses

An existing in-use office and classroom building on Western Michigan University's main campus was chosen for a redesign project which incorporated study of architectural principles of green building and sustainable design. The study emphasized the central importance of buildings themselves in modem life, their effects on building users and their work, their effects on user relationships with one another and the surrounding environment, and the need to enhance the building's positive, natural, and life-supporting relationship with the total environment including the users.

The redesign problem statement reflected issues and ideas from recent architectural and building construction literature, which emphasized green …

Flexible Electrical And Software Programmable Transceivers For Wireless Communications (Feast Ii), Mike Ellinger, James Etters, Eric Juntunen

Honors Theses

Flexible Electrical and Software Programmable Transceivers (FEAST) is a project aimed at advancing both research and educational opportunities in wireless communications. The development of high speed analog-to-digital and digital-to-analog converters has enabled the modulation/demodulation of communications signals via real-time data processing. These "software radios" will allow greater flexibility in the reception and transmission of wireless signals. The FEAST wireless transceiver is such a system consisting of analog RF signal down converters and upconverters, high speed analog-to-digital and digital-toanalog converters, hardware digital signal processing IC's and real time software signal processing.

Phase II of the project (FEASTII) project focuses is on …