Engineering Commons^™

Understanding The Surface Fouling Mechanism Of Ultrananocrystalline Diamond Microelectrodes Using Microfluidics For Neurochemical Detection, An-Yi Chang

Doctoral Dissertations

Electrochemical methods are widely used for chronic neurochemical sensing, but thus far, the organic solution redox reactions fouled the electrodes' surface. It caused the reduction of sensitivity and the electrodes' lifetime.

Here, we present the boron-doped nanocrystalline diamond microelectrodes (BDUNCD) as the next generation electrode material for neurochemical sensor development. To aid in long-term chronic monitoring of neurochemicals, they have a wide window of electrochemical potential, extremely low background current, and excellent chemical inertness. The main research goal is to reduce the rate of electrode fouling due to the reaction by-products, and significantly extend their useful lifetime.

We systematically characterize …

Electrochemical Behavior Of Dense Electrodes For Impedancemetric Nox Sensors, Nabamita Pal

Doctoral Dissertations

NOx (NO and NO2) exhaust gas sensors for diesel powered vehicles have traditionally consisted of porous platinum (Pt) electrodes along with a dense ZrO2 based electrolyte. Advancement in diesel engine technology results in lower NOx emissions. Although Pt is chemically and mechanically tolerant to the extreme exhaust gas environment, it is also a strong catalyst for oxygen reduction, which can interfere with the detection of NOx at concentrations below 100 ppm. Countering this behavior can add to the complexity and cost of the conventional NO x sensor design. Recent studies have shown that dense electrodes are less prone to heterogeneous …

Stretching The Limits Of Dynamic Range, Shielding Effectiveness, And Multiband Frequency Response, Matthew J. Hartmann

Doctoral Dissertations

In this dissertation, an RF MEMS variable capacitor suitable for applications requiring ultrawide capacitive tuning ranges is reported. The device uses an electrostatically tunable liquid dielectric interface to continuously vary the capacitance without the use of any moving parts. As compared to existing MEMS varactors in literature, this device has an extremely simple design that can be implemented using simple fabrication methods that do not necessitate the use of clean room equipment. In addition, this varactor is particularly suited for incorporating a wide range of liquid dielectric materials for specific tuning ratio requirements.

Additionally, the shielding effectiveness performance of graphene-doped …

Design, Modeling, Fabrication, And Testing Of A Multistage Micro Gas Compressor With Piezoelectric Unimorph Diaphragm And Passive Microvalves For Microcooling Applications, Shawn Thanhson Le

Doctoral Dissertations

This dissertation investigates the development of a multistage micro gas compressor utilizing multiple pump stages cascaded in series to increase the pressure rise with passive microvalves and piezoelectric unimorph diaphragms. This research was conducted through modeling, simulation, design, and fabrication of the microcompressor and its components. A single-stage and a two-stage microcompressor were developed to demonstrate and compare the performance and effectiveness of using a cascaded multistage design.

Steady fluid flow through static microvalves structure was studied to gain insight on its gas flow dynamics and characteristics. Transient analysis combined with the structure's interaction was investigated with an analytical model …

Energy Harvesting Using Photovoltaic And Betavoltaic Devices, Ashish Sharma

Doctoral Dissertations

There is an important need for improvement in both cost and efficiency of photovoltaic cells. For improved efficiency, a better understanding of solar cell performance is required. An analytical model of thin-film silicon solar cell, which can provide an intuitive understanding of the effect of illumination on its charge carriers and electric current, is proposed. The separate cases of homogeneous and inhomogeneous charge carrier generation rates across the device are investigated. This model also provides for the study of the charge carrier transport within the quasi-neutral and depletion regions of the device, which is of an importance for thin-film solar …

Quartz-Mems: Wet Chemical Etching Assisted By Electromagnetic Energy Sources For The Development Of Quartz Crystal To Be Used For Microelectromechanical Systems, William J. Clower

Doctoral Dissertations

Quartz crystal resonators have been the most commonly used timing devices to date. Today's timing market requires devices to be as small as possible and consume smaller amounts of energy. Because of the market demand, many startup companies have formed to develop silicon resonators as timing devices. Silicon resonators have poor noise and temperature performance (due to its linear temperature versus frequency coefficient). At the moment the only advantage that silicon resonators have over quartz crystal resonators is a small form factor. The photolithography processing method currently being used in industry is a very tedious task, requiring multiple etching steps …

Biosensing With Microcantilever-Based Sensors, Xiaodong Yan

Doctoral Dissertations

Microcantilevers provide an ideal platform for biosensors. The micron-sized transducer brings several advantages, such as high sensitivity, small sample quantity for analysis, portability, implantable sensor devices, and the ability to be mass produced and integrated into standard microelectronic processing technologies like complementary metal oxide seminconductors (CMOS).

The objective of this research is to investigate and develop modification methods of microcanitlevers for biosensing applications.

Two microcantilever modification methods were investigated. They are self-assembly monolayer method and layer-by-layer method. A fundamental procedure for modification of microcantilevers using the layer-by-layer approach was developed for the first time in this research. These modification methods …

Kinetics Of Laser Chemical Vapor Deposition Of Carbon And Refractory Metals, Feng Gao

Doctoral Dissertations

Three-dimensional laser chemical vapor deposition (3D-LCVD) has been used to grow rods of carbon, tungsten, titanium, and hafnium from a variety of hydrocarbons and metal halide-based precursors. A novel computerized 3D-LCVD system was designed and successfully used in the experiments. A focused Nd:Yag laser beam (λ = 1.06 μm) was utilized to locally heat up a substrate to deposition temperature. The rods, which grew along the axis of the laser beam, had a typical diameter of 30–80 μm and a length of about 1 mm. The precursors for carbon deposition were the alkynes: propyne, butyne, pentyne, hexyne, and octyne. Propyne …

Efficient Algorithms And Implementations For Signal Processing, Changbai Xiao

Doctoral Dissertations

A scheme is presented to regain a finite number of lost samples from a Nyquist-rate-sampled band-limited signal f of finite energy by replenishing new sample values of the same number. The result can also be viewed as the solution to a special non-uniform sampling problem.

A scheme is also presented to recover a band-limited function f of finite energy from its sampling values on real sequences with an accumulation point. The result given here can also be viewed as an approach to the extrapolation problem of determination a band-limited function in terms of its given values on a finite interval. …

Bottom-Up Design Of Artificial Neural Network For Single-Lead Electrocardiogram Beat And Rhythm Classification, Srikanth Thiagarajan

Doctoral Dissertations

Performance improvement in computerized Electrocardiogram (ECG) classification is vital to improve reliability in this life-saving technology. The non-linearly overlapping nature of the ECG classification task prevents the statistical and the syntactic procedures from reaching the maximum performance. A new approach, a neural network-based classification scheme, has been implemented in clinical ECG problems with much success. The focus, however, has been on narrow clinical problem domains and the implementations lacked engineering precision. An optimal utilization of frequency information was missing. This dissertation attempts to improve the accuracy of neural network-based single-lead (lead-II) ECG beat and rhythm classification. A bottom-up approach defined …

The Optimized Electrostatic Motor, Christopher Lee Rambin

Doctoral Dissertations

The most common means of electrically activated actuation is the electromagnetic motor. All electromagnetic motors have a low output to weight ratio and low energy efficiency. The motor's weight is due to the coils and magnets used to generate propulsion. The energy loss is mainly the result of Joule heating that is inherent with any current driven device. An electrostatic motor offers the potential of significantly less weight and higher energy efficiency. This lower weight characteristic is due to the epoxide material used to construct the major components of its propulsion unit. Greater efficiency results from the reduced Joule heating …