Engineering Commons^™

Optimal Temperature-Actuated Control Of A Thermally-Insulated Roller Blind, Hani Alkhatib, Philippe Lemarchand, Brian Norton, Dominic O'Sullivan

Articles

By altering the thermal equilibria between internal and ambient environments, dynamic insulation can minimize heating and cooling building energy requirements. The performance of a thermally-insulated roller blind was evaluated both experimentally and via simulation studies. The variation of blind position was optimized to minimize building energy consumption, maintain thermal comfort, and minimize daylight discomfort for a particular system, location and conditions. The roller blind was adjusted between four positions, from fully-open to fully-closed, optimal indoor temperature switching thresholds found for moving to these blind positions were 15 °C, 18.4 °C, 19.4 °C and 21.4 °C, respectively. Using these resulted in …

Numerical Simulation Of The Donor-Assisted Stir Material For Friction Stir Welding Of Aluminum Alloys And Carbon Steel, Joseph Maniscalco, Abdelmageed A. Elmustafa, Srinivasa Bhukya, Zhenhua Wu

Mechanical & Aerospace Engineering Faculty Publications

In this research effort, we explore the use of a donor material to help heat workpieces without wearing the tool or adding more heat than necessary to the system. The donor material would typically be a small piece (or pieces) of material, presumably of lower strength than the workpiece but with a comparable melting point. The donor, a sandwich material, is positioned between the tool head and the material to be welded, where the tool initially plunges and heats up in the same manner as the parent material that is intended for welding. The donor material heats up subsequent to …

Performance Modeling And Analysis Of A Thermoelectric Building Envelope For Space Heating, Xiaoli Liu, Ming Qu, Kazuaki Yazawa, Jorge Kohanoff, Piotr Chudzinski, Lorenzo Stella, Brian Norton, Niall Holmes Dr., Ruchita Jani, Hongxi Yin

Conference papers

To provide energy-efficient space heating and cooling, a thermoelectric building envelope (TBE) embeds thermoelectric devices in building walls. The thermoelectric device in the building envelope can provide active heating and cooling without requiring refrigerant use and energy transport among subsystems. Thus, the TBE system is energy and environmentally friendly. A few studies experimentally investigated the TBE under limited operating conditions, and only simplified models for the commercial thermoelectric module (TEM) were developed to quantify its performance. A holistic approach to optimum system performance is needed for the optimal system design and operation. The study developed a holistic TBE-building system model …

Perry Center Supplemental Heating, Bekah Kruger, Sam Lonard, Nick Willis

Student Scholarship – Engineering

Students will design a supplemental heat system to help increase the temperature of the fluid in the Geothermal heat system.  Currently the Geothermal system does not provide adequate heating for Perry Center during the winter.  A heat exchanger has been proposed by the Physical Plant to remedy the problem.

Forecast Of Community Total Electric Load And Hvac Component Disaggregation Through A New Lstm-Based Method, Huangjie Gong, Rosemary E. Alden, Aron Patrick, Dan Ionel

Power and Energy Institute of Kentucky Faculty Publications

The forecast and estimation of total electric power demand of a residential community, its baseload, and its heating ventilation and air-conditioning (HVAC) power component, which represents a very large portion of a community electricity usage, are important enablers for optimal energy controls and utility planning. This paper proposes a method that employs machine learning in a multi-step integrated approach. An LSTM model for total electric power at the main circuit feeder is trained using historic multi-year hourly data, outdoor temperature, and solar irradiance. New key temperature indicators, TmHAVC, corresponding to the standby zero-power operation for HVAC systems for summer cooling …

Artificial Intelligence Method For The Forecast And Separation Of Total And Hvac Loads With Application To Energy Management Of Smart And Nze Homes, Rosemary E. Alden, Huangjie Gong, Evan S. Jones, Cristinel Ababei, Dan M. Ionel

Electrical and Computer Engineering Faculty Publications

Separating the HVAC energy use from the total residential load can be used to improve energy usage monitoring and to enhance the house energy management systems (HEMS) for existing houses that do not have dedicated HVAC circuits. In this paper, a novel method is proposed to separate the HVAC dominant load component from the house load. The proposed method utilizes deep learning techniques and the physical relationship between HVAC energy use and weather. It employs novel long short-term memory (LSTM) encoder-decoder machine learning (ML) models, which are developed based on future weather data input in place of weather forecasts. In …

Virtual Power Plant Control For Large Residential Communities Using Hvac Systems For Energy Storage, Huangjie Gong, Evan S. Jones, Rosemary E. Alden, Andrew G. Frye, Donald G. Colliver, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Heating, ventilation, and air-conditioning (HVAC) systems use the most electricity of any household appliance in residential communities. HVAC system modeling facilitates the study of demand response (DR) at both the residential and power system levels. In this article, the equivalent thermal model of a reference house is proposed. Parameters for the reference house were determined based on the systematic study of experimental data obtained from fully instrumented field demonstrators. Energy storage capacity of HVAC systems is calculated and an equivalent state-of-charge is defined. The uniformity between HVAC systems and battery energy storage system is demonstrated by DR control. The aggregated …

Generalized Energy Storage Model-In-The-Loop Suitable For Energy Star And Cta-2045 Control Types, Huangjie Gong, Evan S. Jones, A. H. M. Jakaria, Aminul Huque, Ajit Renjit, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

The paper proposes a generalized energy storage (GES) model for battery energy storage systems (BESS), electric water heaters (EWH) and heating, ventilation, and air-conditioning (HVAC) systems. The analogies, including state of charge versus water temperature differential, are identified and explained, and models-in-the-loop (MIL) are introduced, which are compatible with the Energy Star and CTA-2045 general specifications and command types. Emphasis is placed on the proposed EWH model as it needfully fulfills a gap in present literature. The corresponding MIL has been implemented in the DER integration testbed, which was originally developed by EPRI, and satisfactorily validated against experimental results. A …

Power Factor And Reactive Power In Us Residences – Survey And Energyplus Modeling, Hope C. Anderson, Abdullah Al Hadi, Evan S. Jones, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Electric power systems are experiencing a growing number of electronic loads in the residential sector as modern appliance technology progresses, and it has become increasingly more important to consider the total power factor (PF) of residential communities. This paper provides a survey based on literature and publicly available information of typical appliance PF values and effects at the residential level as well as a discussion on appliance energy use and corresponding operation schedules. A procedure for the calculation of equivalent PF is proposed and exemplified with minutely experimental data at 15-minute and hourly time intervals, which correspond to smart metering …

Demand Response Of Hvacs In Large Residential Communities Based On Experimental Developments, Huangjie Gong, Evan S. Jones, Rosemary E. Alden, Andrew G. Frye, Donald G. Colliver, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Heating, ventilation, and air-conditioning (HVAC) systems contribute the largest electricity usage for a residential community. Modeling of the HVAC systems facilitate the study of demand response (DR) at both the residential and the power system level. In this paper, the equivalent thermal model of a reference house was proposed. Parameters for the reference house were determined based on the systematic study of experimental data obtained from fully instrumented field demonstrators. The aggregated HVAC load was modeled based on the reference house while considering a realistic distribution of HVAC parameters derived from data that was provided by one of the largest …

The Effect Of High Efficiency Building Technologies And Pv Generation On The Energy Profiles For Typical Us Residences, Evan S. Jones, Rosemary E. Alden, Huangjie Gong, Andrew G. Frye, Donald G. Colliver, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

The penetrations of high efficiency technologies and photovoltaic (PV) generation are increasing in the residential sector. Technologies such as improved insulation and efficient HVAC systems significantly affect the energy profile of a house. This effect varies due to climate characteristics, i.e. temperature, solar radiation, relative humidity, and wind speeds. The effect of other technologies, such as efficient water heaters, lighting, or kitchen appliances, is mainly governed by human behavior, which may be represented by a schedule. This paper studies the performance of both climate-influenced and scheduled household devices among different levels of efficiency through combined computational and experimental methods. Three …

Study On Performance Evaluation Of Co2 Heat Pump System Integrated With Thermal Energy Storage For Space Heating, Zhihua Wang, Yuxin Zheng, Fenghao Wang, Mengjie Song, Zhenjun Ma

Faculty of Engineering and Information Sciences - Papers: Part B

CO2 heat pumps have drawn a great deal of attention owing to their advantages of high efficiency and environmental friendly for heating water under low ambient temperature. However, the system performance is not desirable and shows a lower COP for space heating, especially for a radiator as heating terminal, due to the higher inlet water temperature at the gas cooler, which causes a large throttle loss when the refrigerant flow through the throttling device. To tackle this issue, a transcritical CO2 heat pump system integrated with thermal energy storage (TES) systems was developed in this paper. The heating performance of …

Above-Roof Temperature Impacts On Heating Penalties Of Large Cool Roofs In Australian Climates – Final Report, Wenye Lin, Alan Green, Georgios Kokogiannakis, Paul Cooper

Faculty of Engineering and Information Sciences - Papers: Part B

This report outlines the key outcomes of research project RP1037u1 ‘Above-Roof Temperature Impacts on Heating Penalties of Large Cool Roofs in Australian Climates’, an extension to project RP1037 ‘Driving increased utilisation of cool roofs on large-footprint buildings’. The research has been focused on two key aspects of roof thermal performance that had, up until the time of writing, not been taken into account in most investigations into cool roof technology: 1. The condensation and evaporation of dew on the roof surface, and the effect this has on roof temperature by way of: a. The latent heat that is absorbed and …

Impact Of Hysteresis Heating Of Railroad Bearing Thermoplastic Elastomer Suspension Pad On Railroad Bearing Thermal Management, Oscar O. Rodriguez, Arturo A. Fuentes, Constantine Tarawneh

Mechanical Engineering Faculty Publications and Presentations

It is a known fact that polymers and all other materials develop hysteresis heating due to the viscoelastic response or internal friction. The hysteresis or phase lag occurs when cyclic loading is applied leading to the dissipation of mechanical energy. The hysteresis heating is induced by the internal heat generation of the material, which occurs at the molecular level as it is being disturbed cyclically. Understanding the hysteresis heating of the railroad bearing elastomer suspension element during operation is essential to predict its dynamic response and structural integrity, as well as to predict the thermal behavior of the railroad bearing …

Ozone Removal Efficiency And Surface Analysis Of Green And White Roof Hvac Filters, Omed A. Abbass, David Sailor, Elliott T. Gall

Mechanical and Materials Engineering Faculty Publications and Presentations

Heating, ventilation, and air-conditioning ( HVAC ) system filters from a commercial building were tested for their ability to remove ozone from intake air. Filters were taken from rooftop HVAC systems installed for two months: one located on a white membrane roof and the other on a vegetated green roof. One new, unused filter sample was tested as a reference. Samples from these filters were exposed to ozonated air streams at 40 and 120 ppb and relative humidity levels of 30% and 70%. Filter surfaces were analyzed with a scanning electron microscope to observe the structure and composition of the …

Hysteresis Heating Of Railroad Bearing Thermoplastic Elastomer Suspension Element, Oscar O. Rodriguez, Arturo A. Fuentes, Constantine Tarawneh, Robert E. Jones

Mechanical Engineering Faculty Publications and Presentations

Thermoplastic elastomers (TPE’s) are increasingly being used in rail service in load damping applications. They are superior to traditional elastomers primarily in their ease of fabrication. Like traditional elastomers they offer benefits including reduction in noise emissions and improved wear resistance in metal components that are in contact with such parts in the railcar suspension system. However, viscoelastic materials, such as the railroad bearing thermoplastic elastomer suspension element (or elastomeric pad), are known to develop self-heating (hysteresis) under cyclic loading, which can lead to undesirable consequences. Quantifying the hysteresis heating of the pad during operation is therefore essential to predict …

Linear Regression Models For Prediction Of Annual Heating And Cooling Demand In Representative Australian Residential Dwellings, Navid Aghdaei, Georgios Kokogiannakis, Daniel J. Daly, Timothy J. Mccarthy

Faculty of Engineering and Information Sciences - Papers: Part B

This paper presents the development methodology of linear regression models that were developed for the prediction of annual thermal loads in representative residential buildings across three major climates in New South Wales, Australia, and the assessment of the impact of building envelope upgrades. A differential sensitivity analysis was undertaken for sixteen building envelope parameters, with six parameters being identified as significant. These six parameters were then explored using EnergyPlus simulation, and a number of linear regression models developed from the simulation outputs. Random values for design parameters were generated, and the results of EnergyPlus simulations using these parameters were used …

Evaluation Of The Impact Of Slab Foundation Heat Transfer On Heating And Cooling In Florida, Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

The U.S. Department of Energy's Building America Partnership for Improved Residential Construction (BA-PIRC) performed experiments in the Florida Solar Energy Center's Flexible Residential Test Facility intended to assess for the first time (1) how slab-on-grade construction influences interior cooling in a cooling-dominated climate and (2) how the difference in a carpeted versus uncarpeted building might influence heating and cooling energy use.

Enhancing The Thermal Performance Of Temporary Fabric Structures For The Advanced Energy Efficient Shelter System, Justin E. Eshleman, Robert A. Lake, Ronald A. Coutu Jr.

Electrical and Computer Engineering Faculty Research and Publications

The focus of this research is to characterize the thermal load on temporary fabric shelters deployed in the Middle East in order to establish realistic contract specification for the thermal performance of future shelters. Three different testing methods were utilized to evaluate shelter thermal performance. Small-scale tests allowed for economical comparisons of different shelter materials and configurations.

Temperature Measurements During High Flux Ion Beam Irradiations, M. L. Crespillo, Joseph T. Graham, Y. Zhang, W. J. Weber

Nuclear Engineering and Radiation Science Faculty Research & Creative Works

A systematic study of the ion beam heating effect was performed in a temperature range of -170 to 900 °C using a 10 MeV Au³⁺ ion beam and a Yttria stabilized Zirconia (YSZ) sample at a flux of 5.5 x 10¹² cm^-2 s^-1. Different geometric configurations of beam, sample, thermocouple positioning, and sample holder were compared to understand the heat/charge transport mechanisms responsible for the observed temperature increase. The beam heating exhibited a strong dependence on the background (initial) sample temperature with the largest temperature increases occurring at cryogenic temperatures and decreasing with increasing temperature. …

Corrigendum To “Energy Savings Across Eu Domestic Building Stock By Optimizing Hydraulic Distribution In Domestic Space Heating Systems”, Ciara Ahern, Brian Norton

Articles

No abstract.

A Review On Numerical Solutions To Self-Heating Of Coal Stockpile: Mechanism, Theoretical Basis, And Variable Study, Jian Zhang, Ting X. Ren, Yuntao Liang, Zhongwei Wang

Faculty of Engineering and Information Sciences - Papers: Part A

Self-heating or even spontaneous combustion of stockpiled coal, which is likely to outbreak under favourable circumstances during its transport, process, and storage, is a long-standing thermal dynamic hazard. This hazard is harmful in diverse aspects: causing loss of coal resource and caking property, raising safety concerns upon occurrence of open fire, and giving off noxious/greenhouse effect gases. Due to the complexity of involved physical process (e.g. heat and mass transport) and chemical process (e.g. coal oxidation), formulating an analytical solution to the problem with or even without a transient approach would be a daunting task and the problem is thus …

Transient Cfd Modelling Of Low-Temperature Spontaneous Heating Behaviour In Multiple Coal Stockpiles With Wind Forced Convection, Jian Zhang, Yuntao Liang, Ting X. Ren, Zhongwei Wang, Gongda Wang

Faculty of Engineering and Information Sciences - Papers: Part A

Spontaneous heating of coal stockpile has long been a thermal dynamic hazard during coal storage, processing, and transport. A transient non-equilibrium thermal CFD model has been developed to study the low-temperature self-heating behaviour of coal in multiple stockpiles under different prevailing wind conditions. Modelling results from the initial steady wind flow simulation indicate that a wake region can be induced on the leeward side of each coal stockpile. Pressure coefficient drops when the wind stream encounters or leaves a stockpile and the pressure coefficient profiles of multiple stockpiles tend to have more resemblance with a wider spacing. The first stockpile …

Cooling And Heating Season Impacts Of Right-Sizing Of Fixed- And Variable-Capacity Heat Pumps With Attic And Indoor Ductwork, Florida Solar Energy Center, James Cummings

FSEC Energy Research Center®

The U.S. Department of Energy's research team Building America Partnership for Advanced Residential Construction implemented two phases of experiments to examine the cooling and heating seasonal and peak demand performance of a variable-capacity 2-ton SEER 22 heat pump versus a 3-ton variable-capacity SEER 21 heat pump with attic ducts and indoor ducts. The experiments also compared the cooling and heating seasonal and peak demand performance of 2-ton versus 3-ton fixed-capacity SEER 13 heat pumps with attic ducts and indoor ducts.

Energy Savings Across Eu Domestic Building Stock By Optimizing Hydraulic Distribution In Domestic Space Heating Systems, Ciara Ahern, Brian Norton

Articles

The objective of this work is to quantify the resultant savings across the EU from the optimization of existing system components in domestic space heating distribution systems to maintain comfort levels. Heat energy savings are shown to range from 1% to 19% depending on dwelling type, age, location and initial specific heat energy consumption.

Flexible Residential Test Facility: Impact Of Infiltration And Ventilation On Measured Heating Season Energy And Moisture Levels, Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

Perhaps no residential topic has been discussed as much among building scientists as air infiltration and required mechanical ventilation. Usually, envelope tightening is recommended as an efficiency strategy for retrofitting an existing home. In humid climates, reducing infiltration can reduce summer moisture loads. However, during drier weather when the air conditioner is not running, lower infiltration can lead to potential condensation. Even though severe cold weather is rare in the Deep South, the prevalence of single-pane windows can lead to condensation events.

Technical Subtopic 2.1: Modeling Variable Refrigerant Flow Heat Pump And Heat Recovery Equipment In Energyplus, Florida Solar Energy Center, Richard Raustad

FSEC Energy Research Center®

The University of Central Florida/Florida Solar Energy Center, in cooperation with the Electric Power Research Institute and several variable-refrigerant-flow air conditioning (VRF AC) manufacturers, provided a detailed computer model for a VRF AC system in the United States Department of Energy's (U.S. DOE) EnergyPlus' building energy simulation tool. No other simulation tool currently has the capability to accurately model this state-of-the-art VRF heating, ventilating, and air conditioning (HVAC) equipment. Detailed laboratory testing and field demonstrations were performed to measure equipment performance and compare this performance with that predicted by the use of this new model through computer simulation.

This project …

Determining Appropriate Heating And Cooling Thermostat Set Points For Building Energy Simulations For Residential Buildings In North America, Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

Existing building energy simulation tools have a purported tendency to over-predict heating use and, in some cases, to under-predict cooling use, an outcome often attributed to inappropriate assumptions about thermostat management. As a result, a systematic review was conducted for the purposes of determining typical heating and cooling set points for single-family houses in North America. The preliminary consensus results provide an empirical basis for establishing typical inputs for building energy simulation models, increasing prediction accuracy of heating and cooling loads. The results of this review have been applied as default values in the Lawrence Berkeley National Laboratory's Home Energy …

Evaluation Of Proximity Heating Effects In Power Cables, Jonathan Blackledge, Eugene Coyle, Kevin O'Connell

Articles

No abstract provided.

Agenda: 2012 Energy Justice Conference And Technology Exposition, University Of Colorado Boulder. Center For Energy & Environmental Security, University Of Colorado Boulder. Colorado European Union Center Of Excellence, University Of Colorado Boulder. Presidents Leadership Institute

2012 Energy Justice Conference and Technology Exposition (September 17-18)

Co-sponsored with the Colorado European Union Center of Excellence and the Presidents Leadership Institute at the University of Colorado Boulder.

The ability to harness energy is fundamental to economic and social development. Worldwide, almost 3 billion people have little or no access to beneficial energy resources for cooking, heating, water sanitation, illumination, transportation, or basic mechanical needs. Energy poverty exacerbates ill health and economic hardship, and reduces educational opportunities, particularly for women and children. Specifically, access to efficient and affordable energy services is a prerequisite for achieving the Millennium Development Goal (MDG) relating to poverty eradication.

In response, the UN …