Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 4 of 4
Full-Text Articles in Engineering
Co-Polymers Of Furan With Pyrrole Or Thiophene: A Synthetic Study, Rose M. Mcconnell, Walter E. Godwin, Susan E. Baker, Kenya Powell, Martha Baskett, Amy Morara, Xiadong Ma
Co-Polymers Of Furan With Pyrrole Or Thiophene: A Synthetic Study, Rose M. Mcconnell, Walter E. Godwin, Susan E. Baker, Kenya Powell, Martha Baskett, Amy Morara, Xiadong Ma
Journal of the Arkansas Academy of Science
The use of conductive polymers as a substitute for metallic conductors and semiconductors has attracted much attention in the literature. In particular, aromatic heterocyclic polymers constitute an important class since they possess chemical and electrical stability in both the oxidized (doped) and neutral (undoped) state. Doping a polymer allows one to vary its electrical, mechanical, optical, and thermal properties. The properties of these polymers are promising for their many technological uses such as antistatic coatings, solar cells, and electronic devises. Polyfuran is among the least common heterocyclic polymers. Polyfuran has been reported to be much less stable that either polypyrrole …
Pressure And Flow Validation Of A Second Generation Gas Extraction Probe For A Hybrid Rocket Gas Extraction System, Constance Meadors, Andrew B. Wright
Pressure And Flow Validation Of A Second Generation Gas Extraction Probe For A Hybrid Rocket Gas Extraction System, Constance Meadors, Andrew B. Wright
Journal of the Arkansas Academy of Science
A gas extraction system (GES) has been designed for use with the hybrid rocket facility at the University of Arkansas at Little Rock (UALR) for spectroscopic analysis of rocket plumes. While monitoring gas flow-rate and pressure, the GES extracts gases from the hybrid rocket plume and transports them to a mass spectrometer. This paper describes design and construction of a gas extraction probe (GEP) prototype capable of extracting gases directly from the plume. Gas dynamics equations were used to design two venturi-type GEP, converging and converging-diverging. The probe was tested with air to verify design assumptions. Flow rate through the …
Stability And Optimization Of Photoconductivity In Thermally Vacuum Evaporated Indium (Iii) Sulfide Thin Films, Gustavo Rehder, Robert Engelken, Randy Stidham, Richard Tanner, Lee Ketchum, Anil Baral
Stability And Optimization Of Photoconductivity In Thermally Vacuum Evaporated Indium (Iii) Sulfide Thin Films, Gustavo Rehder, Robert Engelken, Randy Stidham, Richard Tanner, Lee Ketchum, Anil Baral
Journal of the Arkansas Academy of Science
Long term stability of photosensitivity versus time in indium (III) sulfide thin films thermally vacuum evaporated onto photocell-patterned printed circuit boards varies sensitively with several factors including contact metal type, contact metal diffusion and electromigration into the semiconductor, doping, and encapsulation method. Because of the significant photoconductivity and relative low toxicity and environmental impact of this compound semiconductor, it is important to better characterize these dependences toward commercial applications. We will report on measurements of photoconductivity vs. time as functions of such factors and evolving methods to stabilize this photoconductivity.
Modeling Of Electrofusion Coils For Performance Optimization, Steve Farmer, Robert A. Sims
Modeling Of Electrofusion Coils For Performance Optimization, Steve Farmer, Robert A. Sims
Journal of the Arkansas Academy of Science
Modeling physical parameters provides a virtual design environment allowing the confirmation and optimization of electrofusion characteristics. Finite element incorporate physical parameters and their interactions along common boundaries defined within a model geometry. The electrofusion of polymeric piping is a widely accepted means of assembling piping systems with zero-leakage integrity. The key parameters in the fusion process are the coil resistance, the current passing through the coil and the time the current is applied. Modeling the coil and applying current to the model is accomplished using the MATLABpartial differential equations (PDE) toolbox. This paper presents the method of modeling and the …