Engineering Commons^™

A Study Of A Plane Dislocation Problem, Daniel D. Kana

Mechanical Engineering ETDs

This paper treats a more complete solution to the logarithmic spiral problem. Some changes in the basic dislocation theory are first accomplished to generalize the form of functions involved. The resulting equations are then applied to the logarithmic spiral dislocation at a hole in a large plate. A complete solution of pertinent stresses is obtained. Data are calculated to obtain the required dislocation relation along the logarithmic spiral cut, circumferential stress at the hole, and maximum shear stress along the dislocation cut.

Pulse Height Digitizer For Fast Random Pulses, Andrew E. Pope

Electrical and Computer Engineering ETDs

The purpose of this project was to develop airborne electronic equipment which would digitize the amplitude of random, fast, video pulses to an accuracy greater than one percent. For a detailed description of this task, refer to Appendix A, Research Contract Proposal 56-13AEE, “Development of an Anglo-To-Digital Converter.” This report covers the complete system design and the development of several basic circuits, in their practical form, which demonstrate system design feasibility.

Critical Masses Of Oralloy Cylinders With Multiple Reflectors Of Medium Z Elements, David P. Wood

Mechanical Engineering ETDs

Critical mass is influenced mainly by the density, concentration, and shape of the fissionable material, the degree of neutron moderation, and the type and thickness of reflector material. Most of these parameters have been explored in detail at the Pajarito Remote-Control Laboratory (1) and the present series of measurements has the purpose of investigating reflector materials in the middle of the periodic table for the more subtle influence of their resonance scattering structure.

A Study Of The Flow Characteristics In The Core Region Of The Sandia Engineering Reactor, James A. Moeller

Chemical and Biological Engineering ETDs

The core region of a nuclear rector is an extremely compact area with a capability of providing a very high heat output. Regardless of the type of coolant used, the heat transfer characteristics of this region must be adequately designed to prevent any undesirable "hot-spots" from developing. The Sandia Engineering Reactor has one of the most compact cores of any in currently operating nuclear reactors. For this reason it is necessary to investigate fully the heat transfer characteristics of the core. The rate of heat transfer from the fuel elements to the coolant is directly dependent upon the temperature difference …

Demodulation Of A Special Am-Fm Signal, Donald W. Dearholt

Electrical and Computer Engineering ETDs

As telemetry becomes more and more important in returning information, new types of modulation arise. Sometimes the modulation used is a direct result of a particular type of transducer, although the output of the transducer may be modified before the carrier is modulated to cause a very different type of signal than would otherwise have occurred.

An Evaluation Of The Beggs Deformeter In Two-Dimensional Structural Analysis And An Investigation Of The Deformeter In Three-Dimensional Structural Analysis, Dwight F. Denton

Civil Engineering ETDs

It was the purpose of this thesis to evaluate the Beggs deformeter in two-dimensional structural frames and then investigate the possible use in three-dimensional structural frames. It is intended in dealing with the subject to explain and describe the deformeter apparatus and verify the theoretical principle through actual structural model analysis.

An Investigation Of The Effects Of Pozzolans On New Mexico Concrete Aggregates, Harry W. Montgomery

Civil Engineering ETDs

It was the purpose of this investigation to determine some of the effects a pozzolan has on Portland cement concrete when New Mexico aggregates are used. The specific items investigated were (1) to determine the effects of a pozzolan on the alkali aggregate expansion in concrete; (2) to show the effect on the compressive strength of concrete and the tensile strength of mortar briquettes when part of the Portland cement is replaced with a pozzolan; (3) to determine whether or not the “Mason Jar Expansion Test” would give reliable results; and (4) to determine whether or not an aggregate, with …

A Study Of Minimum Element Syntheis Of A Two-Pole Rc Driving Point Impedance, William F. Carlson

Electrical and Computer Engineering ETDs

The point of view taken in this thesis is from the point of view of economy. A network containing resistors of values 1 ohm and 1 megohm may present problems of accuracy and element tolerance limits which are not aided by the fact that all elements may be increased or decreased by a constant multiplier without changing the shape of the network gain curve.

A Microwave Technique For Determining The Electronic Properties Of A Moving Plasma, Bernard Hayes

Electrical and Computer Engineering ETDs

A microwave interferometer technique which may be used as a diagnostic tool for determining the electronic properties of a moving plasma is described and analyzed. The plasma and microwaves are confined in a wave guide and longitudinal observation is employed. The complex reflection coefficient determined from resultant standing-wave pattern provides the means for obtaining the complex dielectric constant, conductivity, electron concentration and collision frequency of electrons with molecules in the plasma. The plasma used for these experiments is the reaction products of a gas detonation.

Functional And Economic Considerations Of An Electrical Line Feeding Large Concentration Loads, Seth O. Lewis

Electrical and Computer Engineering ETDs

This paper discusses the considerations required for selecting particular characteristics of [transmission lines] and presents an original method of obtaining the most economical solution. A typical problem at the Public Service Company of New Mexico is solved to illustrate the usefulness of this method.

Design And Use Of A High Power Laser For Plasma Generation Studies., Philip N. Mace

Electrical and Computer Engineering ETDs

The advent of high power lasers to the technological scene has introduced the possibility of creating new effects utilizing the interaction of this high intensity light with matter. C. M. Fowler and D. B. Thomson of the Los Alamos Scientific Laboratory suggested in 1963 the possibility of using a high power laser to pre-ionize and heat a target material to be contained in an explosively driven theta pinch machine. There had been calculations performed by John Dawson, Princeton University, and A. Engel­hardt, Westinghouse Research Laboratories, which indicated that such an approach was theoretically feasible. The laser powers required, however, were …

Determination Of Required Component Reliability From System Reliability Requirements, Arthur M. Breipohl

Electrical and Computer Engineering ETDs

No abstract provided.

Analysis And Synthesis Of A Current Regulator System, William P. Aiello

Electrical and Computer Engineering ETDs

This report describes a practical current regulator system used to accurately control the current delivered by a 500 kilowatt motor-generator unit. The generator supplies its current of 2000 amperes at 250 volts to a large water-cooled air-core solenoid used by LASL Group P-7 for experiments in connection with the Sherwood program.

After a general discussion of the system specifications and the basic regulator loop, each of the components in the basic regulator loop is described in considerable detail. The description, in most cases, is mathematical in nature although many circuit diagrams are included with brief descriptions when necessary for proper …