Open Access. Powered by Scholars. Published by Universities.®
- Discipline
Articles 1 - 4 of 4
Full-Text Articles in Engineering
Determination Of Steels In Kentucky Bridges, Theodore Hopwood Ii, Christopher Goff, Sudhir Palle
Determination Of Steels In Kentucky Bridges, Theodore Hopwood Ii, Christopher Goff, Sudhir Palle
Kentucky Transportation Center Research Report
The Kentucky Transportation Cabinet (KYTC) maintains over two hundred steel bridges constructed with types of steel which are unknown. Kentucky Transportation Center (KTC) researchers have developed a procedure for determining steel tensile properties (0.2% yield strength and ultimate tensile strength) which can be used to help identify unknown steels. The procedure involves extracting small coupons from the lower flanges of steel deck girder bridges. Coupons are then machined into sub-sized tensile testing specimens and suitable shapes for chemical analyses. Sub-sized tensile tests returned values generally comparable to those provided in mill certifications of steels purchased for laboratory trials. Several analytical …
Aging Response And Precipitation Behavior After 5% Pre-Deformation Of An Al-Mg-Si-Cu Alloy, Shuoxun Jin, Tungwai Ngai, Liejun Li, Shian Jia, Tongguang Zhai, Dongjie Ke
Aging Response And Precipitation Behavior After 5% Pre-Deformation Of An Al-Mg-Si-Cu Alloy, Shuoxun Jin, Tungwai Ngai, Liejun Li, Shian Jia, Tongguang Zhai, Dongjie Ke
Chemical and Materials Engineering Faculty Publications
In this study, Al-1.00 Mg-0.65 Si-0.24 Cu alloy was solution heat-treated, water-quenched, and then pre-deformed for 5% before aging. The peak hardness and yield strength of the pre-deformed sample with subsequent artificial aging were similar to that of a T6 condition sample. It was also found that the pre-deformation treatment could inhibit the negative influence of natural aging to some degree. After seven days of natural aging, the pre-deformed sample obtained better peak hardness and yield strength upon artificial aging than the sample without pre-deformation. In addition, the pre-deformation treatment could reduce 50% of the artificial aging time to reach …
Pulsed Laser Beam Welding Of Pd43Cu27Ni10P20 Bulk Metallic Glass, Ling Shao, Amit Datye, Jiankang Huang, Jittisa Ketkaew, Sung Woo Sohn, Shaofan Zhao, Sujun Wu, Yuming Zhang, Udo D. Schwarz, Jan Schroers
Pulsed Laser Beam Welding Of Pd43Cu27Ni10P20 Bulk Metallic Glass, Ling Shao, Amit Datye, Jiankang Huang, Jittisa Ketkaew, Sung Woo Sohn, Shaofan Zhao, Sujun Wu, Yuming Zhang, Udo D. Schwarz, Jan Schroers
Electrical and Computer Engineering Faculty Publications
We used pulsed laser beam welding method to join Pd43Cu27Ni10P20 (at.%) bulk metallic glass and characterized the properties of the joint. Fusion zone and heat-affected zone in the weld joint can be maintained completely amorphous as confirmed by X-ray diffraction and differential scanning calorimetry. No visible defects were observed in the weld joint. Nanoindentation and bend tests were carried out to determine the mechanical properties of the weld joint. Fusion zone and heat-affected zone exhibit very similar elastic moduli and hardness when compared to the base material, and the weld joint shows high …
A Tensile Deformation Model For In-Situ Dendrite/Metallic Glass Matrix Composites, J. W. Qiao, T. Zhang, Fuqian Yang, P. K. Liaw, S. Pauly, B. S. Xu
A Tensile Deformation Model For In-Situ Dendrite/Metallic Glass Matrix Composites, J. W. Qiao, T. Zhang, Fuqian Yang, P. K. Liaw, S. Pauly, B. S. Xu
Chemical and Materials Engineering Faculty Publications
In-situ dendrite/metallic glass matrix composites (MGMCs) with a composition of Ti₄₆Zr₂₀V₁₂Cu₅Be₁₇ exhibit ultimate tensile strength of 1510 MPa and fracture strain of about 7.6%. A tensile deformation model is established, based on the five-stage classification: (1) elastic-elastic, (2) elastic-plastic, (3) plastic-plastic (yield platform), (4) plastic-plastic (work hardening), and (5) plastic-plastic (softening) stages, analogous to the tensile behavior of common carbon steels. The constitutive relations strongly elucidate the tensile deformation mechanism. In parallel, the simulation results by a finite-element method (FEM) are in good agreement with the experimental findings and theoretical calculations. The present study gives a mathematical model to clarify …