Open Access. Powered by Scholars. Published by Universities.®
- Discipline
- Keyword
-
- Air blowing (1)
- Air blowing force (1)
- Binder-jet printing (1)
- Bio-composite (1)
- CNC parameters (1)
-
- Cable blowing (1)
- Cable jetting (1)
- Compression testing (1)
- Computational fluid dynamics (1)
- Design (1)
- Design of experiments (1)
- Energy consumption (1)
- Engineering (1)
- Fiber optic cable (1)
- Fiber optic cable installation (1)
- Fluid as particle packets (1)
- Fluid dynamic governing equations (1)
- Forces and stress on fluids (1)
- Machining strategies (1)
- Model-based verification (1)
- Modeling and simulations (1)
- Peripheral energy (1)
- Rain water penetration testing (1)
- SIMULINK model (1)
Articles 1 - 5 of 5
Full-Text Articles in Engineering
Derivation And Validation Of The Friction, Gravitational, And Air Forces Encountered During Installation Of Fiber Optic Cable, Faheed Olayemi Owokoniran
Derivation And Validation Of The Friction, Gravitational, And Air Forces Encountered During Installation Of Fiber Optic Cable, Faheed Olayemi Owokoniran
All Graduate Theses, Dissertations, and Other Capstone Projects
This paper presents an introduction to fiber optic cable and the fiber optic communication system. An important phase in the supply of this new technology is to transport the fiber optic cable to the vicinity of service. Cable pulling and cable blowing - laminar flow; piston type - are the two main methods of installing fiber optic cable. Both methods of installation have limiting factors that need to be evaluated in order to perform a successful installation. The limiting factors for laminar type cable blowing are further discussed in this paper. A method was proposed to determine the forces - …
Air Flow And Rain Water Penetration Analysis On Generator Enclosures Using Cfd Simulations, Sasanka Andawatta Kankanamge
Air Flow And Rain Water Penetration Analysis On Generator Enclosures Using Cfd Simulations, Sasanka Andawatta Kankanamge
All Graduate Theses, Dissertations, and Other Capstone Projects
Rain water penetration testing on power generator units requires a number of complicated procedures, requiring many resources. As such, a Computational Fluid Dynamics (CFD) tool, "FloEFD for Creo" is used to study the water penetration behavior on a OM924 diesel power generator enclosure in a computational environment. First, the three governing equations in fluid dynamics are derived and explained using simple methods. Next, behavior of rain water droplets upon impact is briefly discussed. Air velocity, volumetric flow rate and static pressure drop were measured physically in the OM924 generator enclosure. Then, a CFD model for the OM924 enclosure was developed …
Model-Based Verification For Simulink Design, Victor Oke
Model-Based Verification For Simulink Design, Victor Oke
All Graduate Theses, Dissertations, and Other Capstone Projects
Testing a Model-Based design is the only way to determine the correctness of the designed model but not enough to conclude that the design is error free. Verification exposes all the design errors and describes the functionality of the system. Assertion based verification helps to determine whether the model obey the actual design requirements. This thesis work is mainly based on verification of a Water Tank control system modeling using SIMULINK model.
Machining Strategies Exploring Reduction In Energy Consumption, Abdullah Al Mamun
Machining Strategies Exploring Reduction In Energy Consumption, Abdullah Al Mamun
All Graduate Theses, Dissertations, and Other Capstone Projects
The main aim of this thesis is to explore machining strategies, analyzing energy consumption using Design of Experiments (DOE) at the material removal rate (MRR), compare to cutting geometrical trajectories according to CNC parameters such as spindle RPM, feed rate, depth of cut per pass and total depth of cut. Spindle RPM, depth of cut per pass, and feed rate are selected as the main three factors and each factor has two levels: low-level (-) and high-level (+). These experiments have been performed at an end-milling machine by using a concept of a constant volume of material removal processes in …
Binder Jet Additive Manufacturing Of Stainless Steel-Hydroxyapatite Bio-Composite, Don Suranga Dhanushka Uduwage
Binder Jet Additive Manufacturing Of Stainless Steel-Hydroxyapatite Bio-Composite, Don Suranga Dhanushka Uduwage
All Graduate Theses, Dissertations, and Other Capstone Projects
This study was conducted to create a bio-composite with a porous structure using the binder-jet printing additive manufacturing process. The samples were printed by changing the parameters such as layer thickness, roller speed, sintering time and sintering temperature of the X1-Lab binder jet additive manufacturing printer. The samples were printed 80% stainless steel 316 mixed with 20% Calcium Phosphate Tribasic by volume. Eight experiments were attempted to print according to the fractional factorial design of experiment. The effects of changing parameters on the mechanical properties of the new bio-composite was tested using ASTM E-09 compressive strength standards. The compression testing …