Open Access. Powered by Scholars. Published by Universities.®
- Discipline
Articles 1 - 18 of 18
Full-Text Articles in Engineering
Grain Boundary And Texture Evolution Of Tib/Ti–2al–6sn Titanium Matrix Composite Under Electroshocking Treatment, Yaya Wu, Yan Wen, Anan Guo, Jian Zhou, Fei Yin, Lechun Xie, Liqiang Wang, Lin Hua, Weijie Lu, Lai-Chang Zhang
Grain Boundary And Texture Evolution Of Tib/Ti–2al–6sn Titanium Matrix Composite Under Electroshocking Treatment, Yaya Wu, Yan Wen, Anan Guo, Jian Zhou, Fei Yin, Lechun Xie, Liqiang Wang, Lin Hua, Weijie Lu, Lai-Chang Zhang
Research outputs 2022 to 2026
This work used electroshocking treatment (EST) plus external loading to regulate the microstructure of titanium matrix composites (TMCs). The external loading was 0.3 MPa. After EST plus external loading with 0.3 MPa, the was reduced to 2.53 m in size. The percentage of high angle grain boundaries (HAGBs) in increased first and then decreased. The percent of HAGBs in TiB decreased, mainly due to the introduction of abundant dislocations in the TiB/matrix interface after EST. After EST, the maximum texture strength of TiB decreased from 13.09 to 12.97, and that of decreased from 3.11 to 1.58. After EST under external …
Microstructural And Mechanical Behavior Investigations Of Nb-Reinforced Mg–Sn–Al–Zn–Mn Matrix Magnesium Composites, Ali Ercetin, Özgür Özgün, Kubilay Aslantaş, Oguzhan Der, Bekir Yalçın, Ercan Şimşir, Muhammad Aamir
Microstructural And Mechanical Behavior Investigations Of Nb-Reinforced Mg–Sn–Al–Zn–Mn Matrix Magnesium Composites, Ali Ercetin, Özgür Özgün, Kubilay Aslantaş, Oguzhan Der, Bekir Yalçın, Ercan Şimşir, Muhammad Aamir
Research outputs 2022 to 2026
This research focuses on the fabrication and characterization of TAZ532-xNb composites, employing high-purity, micron-sized powders of Mg, Sn, Al, Zn, Mn, and Nb as the raw materials. These powders were subjected to a paraffin coating process aimed at mitigating oxidation. The formation of composites was achieved via hot pressing and was followed by surface preparation and analysis using scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS). An X-ray diffraction (XRD) study was conducted to identify the microstructural phases. Quantitative assessments including the theoretical density, actual density, and relative density were computed, and their fluctuations in relation to the increasing Nb …
Machining Of Carbon Steel Under Aqueous Environment: Investigations Into Some Performance Measures, Mushtaq Ali, Tahir Abdul Hussain Ratlamwala, Ghulam Hussain, Tauheed Shehbaz, Riaz Muhammad, Muhammad Aamir, Khaled Giasin, Danil Yurievich Pimenov
Machining Of Carbon Steel Under Aqueous Environment: Investigations Into Some Performance Measures, Mushtaq Ali, Tahir Abdul Hussain Ratlamwala, Ghulam Hussain, Tauheed Shehbaz, Riaz Muhammad, Muhammad Aamir, Khaled Giasin, Danil Yurievich Pimenov
Research outputs 2022 to 2026
In this study, a new machining approach (aqueous machining) is applied for mill machining and its performance is compared with traditional wet machining. AISI 1020 steel is employed as the test material and Taguchi statistical methodology is implemented to analyze and compare the performance of the two machining approaches. The cutting speed, feed rate, and depth of cut were the machining parameters used for both types of machining, while the selected response variables were surface roughness and hardness. Temperature variations were also recorded in aqueous machining. Compared with wet machining, aqueous machining resulted in lower surface roughness (up to 13 …
A New Method For Evaluating The Bond Strength Of Plasma-Sprayed Nicrbsi Coatings, Liang Yu Chen, Yi Tong Liu, Hao Nan Xuan, Cui Hua Zhao, Maksym Bobrov, Qian Hao Zang, Jin Hua Peng, Sheng Lu, Lai Chang Zhang
A New Method For Evaluating The Bond Strength Of Plasma-Sprayed Nicrbsi Coatings, Liang Yu Chen, Yi Tong Liu, Hao Nan Xuan, Cui Hua Zhao, Maksym Bobrov, Qian Hao Zang, Jin Hua Peng, Sheng Lu, Lai Chang Zhang
Research outputs 2022 to 2026
The bond strength is a critical consideration for the plasma-sprayed NiCrBSi coatings. However, the conventional methods for testing the bond strength of NiCrBSi coatings always cost time and money. If there is a simple method that could predict the bond strength of the prepared NiCrBSi coatings without destroying the coatings, it would be significantly beneficial for industrial applications. In this work, a new method was proposed based on the total areas of the interfacial pores for the NiCrBSi coatings. The NiCrBSi coating was prepared by plasma spraying technology and the as-sprayed coating was subsequently remelted by plasma arc using the …
Electroshock Treatment Dependent Microstructural Evolution And Mechanical Properties Of Near-Β Titanium Alloy Manufactured By Directed Energy Deposition, Haojie Guo, Pu Liu, Xunpeng Qin, Yanli Song, Dongsheng Qian, Lechun Xie, Liqiang Wang, Lai-Chang Zhang, Lin Hua
Electroshock Treatment Dependent Microstructural Evolution And Mechanical Properties Of Near-Β Titanium Alloy Manufactured By Directed Energy Deposition, Haojie Guo, Pu Liu, Xunpeng Qin, Yanli Song, Dongsheng Qian, Lechun Xie, Liqiang Wang, Lai-Chang Zhang, Lin Hua
Research outputs 2014 to 2021
Effects of electroshock treatment (EST) on the microstructural evolution and mechanical properties of near-β titanium alloy (Ti-55531) formed by directed energy deposition (DED) was studied in this work. With the increase in EST time, the average hardness of specimen decreased from 426 HV to 316 HV, and the fracture strain increased significantly, which was attributed to the uniform dispersion of α phase along grain boundaries and inside the β grains. After EST, the texture intensity decreased in terms of the orientation distribution function (ODF), which was ascribed to the redistribution of α phase. Moreover, more atomic vacancies and lattice distortion …
Microstructure Evolution And Mechanical Property Response Of Tc11 Titanium Alloy Under Electroshock Treatment, Chang Liu, Lechun Xie, Dongsheng Qian, Lin Hua, Liqiang Wang, Lai-Chang Zhang
Microstructure Evolution And Mechanical Property Response Of Tc11 Titanium Alloy Under Electroshock Treatment, Chang Liu, Lechun Xie, Dongsheng Qian, Lin Hua, Liqiang Wang, Lai-Chang Zhang
Research outputs 2014 to 2021
© 2020 The Authors This work investigated the effects of electroshock treatment (EST) on the microstructure variation and mechanical properties of TC11 alloy. The average hardness of the specimens decreased from 358 HV to 328 HV after EST of 0.04 s, then increased to 396 HV after EST of 0.06 s. After EST, the yield strength of specimen declined from 959 MPa to 797 MPa after EST of 0.04 s, and then increased to 1265 MPa after EST of 0.06 s, but the fracture strain decreased continuously. The variation in mechanical properties was closely related to the phase transition from …
Analysis Of Microstructure And Mechanical Properties Of Bismuth-Doped Sac305 Lead-Free Solder Alloy At High Temperature, Umair Ali, Hamza Khan, Muhammad Aamir, Khaled Giasin, Numan Habib, Muhammad Owais Awan
Analysis Of Microstructure And Mechanical Properties Of Bismuth-Doped Sac305 Lead-Free Solder Alloy At High Temperature, Umair Ali, Hamza Khan, Muhammad Aamir, Khaled Giasin, Numan Habib, Muhammad Owais Awan
Research outputs 2014 to 2021
SAC305 lead-free solder alloy is widely used in the electronic industry. However, the problems associated with the growth formation of intermetallic compounds need further research, especially at high temperatures. This study investigates the doping of Bismuth into SAC305 in the various compositions of 1, 2, and 3 wt.%. The microstructure in terms of intermetallic compound particles and mechanical properties was examined after thermal aging at temperatures of 100◦C and 200◦C for 60 h. The microstructure examination was observed using scanning electron microscopy, and the chemical composition of each alloy was confirmed with an energy dispersive X-ray. Tensile tests were performed …
Editorial: Structure And Mechanical Properties Of Titanium Alloys And Titanium Matrix Composites (Tmcs), Lechun Xie, Liqiang Wang, Lai-Chang Zhang, Weijie Lu
Editorial: Structure And Mechanical Properties Of Titanium Alloys And Titanium Matrix Composites (Tmcs), Lechun Xie, Liqiang Wang, Lai-Chang Zhang, Weijie Lu
Research outputs 2014 to 2021
No abstract provided.
Influence Of Cr Content On The Microstructure And Mechanical Properties Of Crxfenicu High Entropy Alloys, Hao Wu, Sirui Huang, Chengyan Zhu, Heguo Zhu, Zonghan Xie
Influence Of Cr Content On The Microstructure And Mechanical Properties Of Crxfenicu High Entropy Alloys, Hao Wu, Sirui Huang, Chengyan Zhu, Heguo Zhu, Zonghan Xie
Research outputs 2014 to 2021
© 2020 Chinese Materials Research Society The effect of Cr content on the microstructure and mechanical properties of CrxFeNiCu high entropy alloys (HEAs) was firstly studied by first-principles calculations. The calculated results show that the hardness of the alloys increased with the expense of its plasticity decrease, if the content of Cr in the alloy increased. In order to verify the calculated results, CrxFeNiCu (x = 0.8, 1, 1.5 and 2) high entropy alloys were synthesized by vacuum induction melting in the present study. The results show that as the value of x increased from 0.8 to 2, the crystal …
Evaluation Of Microstructure Variation Of Tc11 Alloy After Electroshocking Treatment, Lechun Xie, Chang Liu, Yanli Song, Haojie Guo, Zhongqi Wang, Lin Hua, Liqiang Wang, Lai-Chang Zhang
Evaluation Of Microstructure Variation Of Tc11 Alloy After Electroshocking Treatment, Lechun Xie, Chang Liu, Yanli Song, Haojie Guo, Zhongqi Wang, Lin Hua, Liqiang Wang, Lai-Chang Zhang
Research outputs 2014 to 2021
Electro-shocking treatment (EST) has been investigated as a pathway to optimise the microstructure and mechanical properties of titanium alloys. The thermal conditions introduced by EST resulted in a phase transformation from α to β. The fraction of β phase decreased from 25.27% to 19.47% after EST for 0.02 s, which was possibly caused by the recrystallization of α phase. The application of EST for 0.04 s resulted in an increase in volume fraction of the β phase to 26.95%. The energy introduced by EST resulted in changes to the direction and intensity of texture within the microstructure with the texture …
Phase Separation And Enhanced Wear Resistance Of Cu88fe12 Immiscible Coating Prepared By Laser Cladding, Shuzhen Zhao, Shengfeng Zhou, Min Xie, Xiaoqin Dai, Dongchu Chen, Laichang Zhang
Phase Separation And Enhanced Wear Resistance Of Cu88fe12 Immiscible Coating Prepared By Laser Cladding, Shuzhen Zhao, Shengfeng Zhou, Min Xie, Xiaoqin Dai, Dongchu Chen, Laichang Zhang
Research outputs 2014 to 2021
In order to eliminate the microstructure segregation of Cu–Fe immiscible alloys which characterized with a liquid miscible gap, the Cu88Fe12 (wt.%) immiscible coating was prepared by laser cladding. The phase separation characteristic and wear resistance of the Cu88Fe12 (wt.%) immiscible coating were also investigated. The results show that the size of the milled Cu88Fe12 composite powder is reduced comparing to that of the un-milled powder due to fracturing during mechanical milling. Moreover, the demixing or delamination disappears in the Cu88Fe12 immiscible coating and a large amount of face-centered-cubic (fcc) γ-Fe and body-centered-cubic (bcc) α-Fe particles are dispersed in the face-centered-cubic …
Nanoindentation Characterization On Local Plastic Response Of Ti-6al-4v Under High-Load Spherical Indentation, Yan Wen, Lechun Xie, Zhou Wang, Liqiang Wang, Weijie Lu, Laichang Zhang
Nanoindentation Characterization On Local Plastic Response Of Ti-6al-4v Under High-Load Spherical Indentation, Yan Wen, Lechun Xie, Zhou Wang, Liqiang Wang, Weijie Lu, Laichang Zhang
Research outputs 2014 to 2021
After high-load spherical indentation treatment, the variations of hardness on the plastic zone of Ti-6Al-4V were investigated via nanoindentation method. The hardness within the center of plastic zone was measured by nanoindenter, and the magnitude decreased gradually along the depth, which were caused by the different extent of plastic deformation under the residual imprint. The microstructure of indentation were observed using scanning electron microscope (SEM) before and after surface etching, and the results showed that the microhardness revealed the average hardness of α and β phases of Ti-6Al-4V. The maximum hardness reached 6.438 GPa in the depth of 132 μm. …
Particle Size-Dependent Microstructure, Hardness And Electrochemical Corrosion Behavior Of Atmospheric Plasma Sprayed Nicrbsi Coatings, Peng Sang, Liang-Yu Chen, Cuihua Zhao, Ze-Xin Wang, Haiyang Wang, Sheng Lu, Dongpo Song, Jia-Huan Xu, Lai-Chang Zhang
Particle Size-Dependent Microstructure, Hardness And Electrochemical Corrosion Behavior Of Atmospheric Plasma Sprayed Nicrbsi Coatings, Peng Sang, Liang-Yu Chen, Cuihua Zhao, Ze-Xin Wang, Haiyang Wang, Sheng Lu, Dongpo Song, Jia-Huan Xu, Lai-Chang Zhang
Research outputs 2014 to 2021
Particle size is a critical consideration for many powder coating-related industries since it significantly influences the properties of the produced materials. However, the effect of particle size on the characteristics of plasma sprayed NiCrBSi coatings is not well understood. This work investigates the microstructures, hardness and electrochemical corrosion behavior of plasma sprayed NiCrBSi coatings synthesized using different-sized powders. All coatings mainly consist of Ni, N3B, CrB, Cr7C3 and Cr3C2 phases. The coatings produced by small particles (50–75 μm) exhibit lower porosity (2.0 ± 0.8%). Such coatings show a higher fraction (15.5 vol.%) of the amorphous phase and lower hardness (700 …
Beta-Type Ti-Nb-Zr-Cr Alloys With Large Plasticity And Significant Strain Hardening, Syed F. Jawed, Chirag D. Rabadia, Y. J. Liu, L. Q. Wang, Y. H. Li, X. H. Zang, Laichang C. Zhang
Beta-Type Ti-Nb-Zr-Cr Alloys With Large Plasticity And Significant Strain Hardening, Syed F. Jawed, Chirag D. Rabadia, Y. J. Liu, L. Q. Wang, Y. H. Li, X. H. Zang, Laichang C. Zhang
Research outputs 2014 to 2021
A series of Ti-25Nb-8Zr-xCr (x = 0, 2, 4, 6, 8 wt%) alloys were designed based on DV-Xα cluster method and e=a-Δr diagram with an anticipation to obtain high plasticity and significant strain hardening. The designed alloys were produced through cold crucible levitation melting technique in order to effectively investigate their micro-structures and mechanical properties. The addition of Cr significantly enhances the β stability in the microstructures of the Ti-25Nb-8Zr-xCr alloys. Both yield strength and hardness of the studied alloys increase due to the effect of solid-solution strengthening. By contrast, the plasticity, maximum strength and strain hardening rate are influenced …
Homogenization And Growth Behavior Of Second-Phase Particles In A Deformed Zr-Sn-Nb-Fe-Cu-Si-O Alloy, Liang-Yu Chen, Peng Sang, Lina Zhang, Dongpo Song, Yanqiu Chu, Linjiang Chai, Laichang Zhang
Homogenization And Growth Behavior Of Second-Phase Particles In A Deformed Zr-Sn-Nb-Fe-Cu-Si-O Alloy, Liang-Yu Chen, Peng Sang, Lina Zhang, Dongpo Song, Yanqiu Chu, Linjiang Chai, Laichang Zhang
Research outputs 2014 to 2021
Homogeneous distribution of fine second-phase particles (SPPs) fabricated by cycles of deformation and annealing in zirconium alloys is a critical consideration for the corrosion resistance of fuel claddings. Different deformation degrees of zirconium alloys would result in distinctive microstructures, leading to a distinct growth of SPPs during subsequent annealing. Unfortunately, the homogenization and growth behavior of SPPs in deformed zirconium alloys have not been well studied. In this work, a β-quenched Zr–Sn–Nb–Fe–Cu–Si–O alloy was rolled and annealed at 580◦C or 680◦C. The morphologies, distributions, and sizes of SPPs resulting from the different processing procedures were investigated. A linear distribution of …
Influence Of Nb On The Β → Α″ Martensitic Phase Transformation And Properties Of The Newly Designed Ti-Fe-Nb Alloys, Shima Ehtemam-Haghighi, Yujing Liu, Guanghui Cao, Lai-Chang Zhang
Influence Of Nb On The Β → Α″ Martensitic Phase Transformation And Properties Of The Newly Designed Ti-Fe-Nb Alloys, Shima Ehtemam-Haghighi, Yujing Liu, Guanghui Cao, Lai-Chang Zhang
Research outputs 2014 to 2021
A series of Ti-7Fe-xNb (x = 0, 1, 4, 6, 9, 11 wt.%) alloys was designed and cast to investigate the β → α″ martensitic phase transformation, β phase stability, the resulting microstructure and mechanical properties. Phase analysis revealed that only Ti-7Fe-11Nb alloy shows a single body-centred cubic β phase microstructure while the others are comprised of β and orthorhombic α″ phases. Moreover, Nb addition up to 11 wt.% enhances the stability and volume fraction of β phase in the microstructure, hence reducing the propensity of the alloy system to form α″ phase during quenching. Compressive yield strength and hardness …
Processing Of Al-12si-Tnm Composites By Selective Laser Melting And Evaluation Of Compressive And Wear Properties, Konda Prashanth, Sergio Scudino, Anil Chaubey, Lukas Löber, Pei Wang, Hooyar Attar, Frank Schimansky, Florian Pyczak, Jürgen Eckert
Processing Of Al-12si-Tnm Composites By Selective Laser Melting And Evaluation Of Compressive And Wear Properties, Konda Prashanth, Sergio Scudino, Anil Chaubey, Lukas Löber, Pei Wang, Hooyar Attar, Frank Schimansky, Florian Pyczak, Jürgen Eckert
Research outputs 2014 to 2021
Al-12Si (80 vol%)-Ti52.4Al42.2Nb4.4Mo0.9B0.06 (at.%) (TNM) composites were successfully produced by the selective laser melting (SLM). Detailed structural and microstructural analysis shows the formation of the Al6MoTi intermetallic phase due to the reaction of the TNM reinforcement with the Al-12Si matrix during SLM. Compression tests reveal that the composites exhibit significantly improved properties (∼140 and ∼160 MPa higher yield and ultimate compressive strengths, respectively) compared with the Al-12Si matrix. However, the samples break at ∼6% total strain under compression, thus showing a reduced plasticity of the composites. Sliding wear tests were carried out for both the Al-12Si matrix and the Al-12Si-TNM …
The Heat Treatment Analysis Of E110 Case Hardening Steel, Majid Tolouei Rad, Eric Lichter
The Heat Treatment Analysis Of E110 Case Hardening Steel, Majid Tolouei Rad, Eric Lichter
Research outputs 2014 to 2021
This paper investigates mechanical and microstructural behaviour of E110 case hardening steel when subjected to different heat treatment processes includingquenching, normalizing and tempering. After heat treatment samples were subjected to mechanical and metallographic analysisand the properties obtained from applying different processes were analysed. The heat treatment process had certain effects on the resultant properties andmicrostructures obtained for E110 steel which are described in details. Quenching produced a martensitic microstructure characterized by significant increase in material’s hardness and a significant decreased in its impact energy. Annealed specimens produced a coarse pearlitic microstructure with minimal variation in hardness and impact energy. For …