Engineering Commons^™

Cooled Liquid Rocket Thrust Chamber, Benjamin Gibson, Kealan Frederick Harris, Ryan Frank Schackel, Bjorn Thorsen

Mechanical Engineering

Cooling may affect the thrust output of a small-scale rocket. Little research is published about small-scale rocket performance. We hypothesize the thrust produced varies as the amount of cooling varies. To facilitate assessing this hypothesis, we have designed and built a liquid rocket engine rated for at approximately 25 lb_f of thrust. Our objective was to build in parallel with Cal Poly Space Systems, who built a rocket engine with similar specifications except without cooling. Our challenge is to integrate film cooling, so that the effects of cooling may be compared to Cal Poly Space System’s engine which has …

Indoor Air Monitoring Of Ethanol And Benzene In A Pilot Winery Using Active Sampling, Andrew I. Kaneda

Master's Theses

Acute indoor concentrations of benzene and ethanol were evaluated in the California Polytechnic State University San Luis Obispo’s pilot winery workroom. Air samples were collected during four different wine-making activities: fermentation, fermentation with Brix content testing, post-alcoholic fermentation pressing, and storage/finishing. Average workroom benzene concentrations ranged from 0.05 to 0.12 mg/m³. Ethanol concentrations in the winery workroom varied with the activity, ranging from 0.9 to 12 mg/m³. Pressing and fermentation with Brix content testing both led to higher indoor ethanol concentrations than fermentation without Brix content testing and storage/finishing.

Tracer gas decay air exchange tests were …

Thermodynamic Efficiency Evaluation For Distillation Of Ethanol, Joe A. Cavaletto

BioResource and Agricultural Engineering

Energy will always be a consideration when distilling any product. Fog’s End Distillery in Gonzales, CA is a small scale micro distillery for ethanol. For Fog’s End, efficiency is key to staying competitive. In this project the efficiency of energy in vs product out will be calculated. While collecting this data the price/bottle for energy will be determined and used for an assembly cost. To determine the efficiency the fuel usage will be recorded for several distillation trials. The mash contents and product contents will all be measured and calculations will be performed to find the theoretical amount of energy …

Integration Of Microfluidics With Surface Plasmon Resonance, Scott B. Fratzke

Master's Theses

This thesis successfully integrates laminate microfluidic devices with an analytic Surface Plasmon Resonance (SPR) instrument. Integration was accomplished at low-cost using materials such as polydimethylsiloxane (PDMS), Poly(methyl methacrylate) (PMMA), Tygon tubing, and a 3-way stopcock. The main components of this thesis are the design and fabrication of the low-cost, in-house fluidics that can integrate with upstream microfluidics and the validation of the in-house fluidics using the Biosensing Instruments BI-2000 SPR instrument. The low-cost fluidics was designed and fabricated “in-house” using a novel investment casting technique that required the use of laser cutting technology to make a master cast, and candle …

Potential Migration Of Ε-Caprolactam To Water And Wine As Affected By Transportation And Storage, Joseph C. Ianneo

Master's Theses

Abstract: Under normal sealing and storage conditions, Nylon-6, poly-caprolactam-based plastic laminates may release impurities to packaged foods and liquids and the application of heat for cooking often increases the rate of migration. Epsilon-caprolactam is one of the main contaminates found to migrate from a Nylon-6 poly-caprolactam plastic film. The objectives of this study were to determine the effects of solvent, transportation and storage time on the migration of ε-caprolactam from a Nylon-6-based lidding material into water or a white wine substitute (12% ethanol). Polypropylene plastic cups were filled, sealed, packaged, stacked and exposed to a simulated 3-day cross-country shipment. Cups …

Temperature Influence And Heat Management Requirements Of Microalgae Cultivation In Photobioreactors, Thomas Hagen Mehlitz

Master's Theses

Microalgae are considered one of the most promising feedstocks for biofuel production for the future. The most efficient way to produce vast amounts of algal biomass is the use of closed tubular photobioreactors (PBR). The heat requirement for a given system is a major concern since the best algae growth rates are obtained between 25-30 °C, depending on the specific strain. A procedure to determine temperature influence on algal growth rates was developed for a lab-scale PBR system using the species Chlorella. A maximum growth rate of 1.44 doublings per day at 29 °C (optimal temperature) was determined. In addition, …