Open Access. Powered by Scholars. Published by Universities.®
- Discipline
- Publication
Articles 1 - 5 of 5
Full-Text Articles in Engineering
Production Optimization Of Ring-Banded Spherulitic Crystals Of Poly (3-Butylthiophene-2,5-Diyl) Using Controlled Solution Evaporation, Frederick Paul Henderson Iii
Production Optimization Of Ring-Banded Spherulitic Crystals Of Poly (3-Butylthiophene-2,5-Diyl) Using Controlled Solution Evaporation, Frederick Paul Henderson Iii
Materials Engineering
Conductive polymers can carry a charge due to the presence of excess electrons along the carbon backbone. By growing these polymers into crystals, the usual insulative isotropic matrix that polymers form will be replaced with anisotropic regions where conduction is possible parallel to the crystal lattice growth direction. In previous research, while growing sphere shaped crystals it was observed that a few would exhibit rings that formed parallel to the circumference of the sphere. In this project, the conditions to produce this ring structure were examined by looking at two polymer solutions (with carbon disulfide or dichlorobenzene as solvent) and …
Non-Toxic Soil Thickeners For Reducing Mudslide Intensity, Miranda Miao, Isaac Blackburn, Erika Haley Yao
Non-Toxic Soil Thickeners For Reducing Mudslide Intensity, Miranda Miao, Isaac Blackburn, Erika Haley Yao
Materials Engineering
Non-toxic food thickeners were investigated as a solution for thickening mud to mitigate the effects of mudslides. All soil was obtained from a site on the California Polytechnic State University campus where a mudslide occurred in 2017. Guar gum was mixed into the soil at 1 wt% and 10 wt% of the moisture content in the soil. Whey protein was mixed into the soil at 2 wt% and 19 wt% of the moisture content in the soil. The soils’ liquid limit was found using the Casagrande cup testing method. Liquid limit testing indicated that thickeners raised the liquid limit, most …
Interim Field Guide For Construction And Testing Of Concrete Shear Wall With Added Frp Layer, Carlos Alberto Espitia
Interim Field Guide For Construction And Testing Of Concrete Shear Wall With Added Frp Layer, Carlos Alberto Espitia
Construction Management
In Los Angeles, many of the hospitals are no longer up to code as they were built in the 1970’s. The shear walls that the hospitals were constructed on stand to experience major failures in the event of a seismic event and this is the issue that this student research team was assigned with. This project was to design, procure, and construct all necessary constraints to be able to test a wall that is fundamentally similar to that of the sheer walls in these hospitals. Once this was complete the goal was to test two walls with an added FRP …
Maximizing Poly(3-Butylthiophene-2,5-Diyl) Electrical Conductivity By Maximizing Transcrystal Growth, Edward Alexander Bicknell
Maximizing Poly(3-Butylthiophene-2,5-Diyl) Electrical Conductivity By Maximizing Transcrystal Growth, Edward Alexander Bicknell
Materials Engineering
Polymers are generally considered electrical insulators. Despite this, research in the mid 1970’s found that polymers consisting of a conjugated backbone structure could become electrically conductive upon doping.1 The conjugated polymer analyzed for this project was poly(3-butylthiophene-2,5-diyl) (P3BT). Transcrystals have been found as a way to promote electrical conductivity through mechanisms including π bond atomic orbital overlap and electron mobility.2 In theory, maximizing transcrystal length would also maximize P3BT electrical conductivity, increasing its applicable use in electronic devices. The goal of this project was to determine a methodological way to maximize P3BT electrical conductivity by producing the longest transcrystal length …
Minimizing The Dimensional Change In Two Component Epoxy Based Thermoset Adhesives Through Adapting Mix Ratio And Initial Crosslink Density, Jefferson Peter Norman
Minimizing The Dimensional Change In Two Component Epoxy Based Thermoset Adhesives Through Adapting Mix Ratio And Initial Crosslink Density, Jefferson Peter Norman
Materials Engineering
Meissner Filtration uses amine-hardened epoxy as a high-performance adhesive to encapsulate hollow fiber membranes at the ends of rigid filter housings. Dimensional change of the epoxy while curing can result in residual stress formation that is detrimental to the manufacturing of the filter and causes structural integrity issues when the filter is used in industrial processes where heating and cooling cycles are implemented. The residual stresses can cause cracks, microscopic fractures, and delamination from the housing, resulting in failure of the filter. The goal of this project was to evaluate how changes in processing conditions could minimize dimensional variability due …