Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 8 of 8
Full-Text Articles in Engineering
Analysis For Hybrid Rocket Fuel Regression Using Stereolithographic Geometry, Michael P. King
Analysis For Hybrid Rocket Fuel Regression Using Stereolithographic Geometry, Michael P. King
Theses and Dissertations
Hybrid Rocket Engines (HRE) have characteristically low fuel regression that limits their performance. Additive manufacturing and rapid prototyping can possibly solve some of the problems with Hybrid propulsion regression by creating geometry not possible with conventional manufacturing. This work is attempting to make geometric regression simulation of HRE easier by using STereoLithography (STL files) as the geometry. This analysis sets flow conditions, boundary conditions, propellant selection, and allows for fuel geometry to be altered to simulate geometry’s effects on regression rate and propellant performance. This model can be used for more advanced geometric analysis to improve and predict performance.
3d Printing For Solving Part Obscolescence, Ayman G. Alqarni
3d Printing For Solving Part Obscolescence, Ayman G. Alqarni
Theses and Dissertations
The purpose of this research was to highlight the issue of parts obsolescence and to highlight the possibility of using alternative methods to overcome parts shortage. Specifically, this thesis sought to answer the research question: is the three-dimensional printing technology (3D) an applicable approach to overcome part obsolescence. The research question was answered through data research and survey analysis. Notwithstanding, the diminished manufacturing sources and material shortages (DMSMS) management and other existing approaches, such as forecasting, contracting, and reverse engineering (RE), were discussed briefly in the literature review and profoundly in chapter IV to differentiate among applicable existing solutions toward …
Investigation Of Ultem 9085 For Use In Printed Orbital Structures, William R. Gallagher
Investigation Of Ultem 9085 For Use In Printed Orbital Structures, William R. Gallagher
Theses and Dissertations
Additive manufacturing is revolutionizing industries ranging from medicine to space. However, the structural characteristics of plastic parts created by these methods are not as well understood as their more established counterparts. This research explored two relevant areas: how the structural characteristics of ULTEM 9085 plastic behaved after exposure to orbital conditions and the design of the cross-sectional area of a beam to be 3-D printed in microgravity based on the expected loads from the printer. To study orbital effects, ULTEM 9085 was printed into 1/4th scale ASTM D638- 14 dogbones using a Stratasys 450mc printer. These dogbones were placed in …
Structural Dynamic And Inherent Damping Characterization Of Additively Manufactured Airfoil Components, Andrew W. Goldin
Structural Dynamic And Inherent Damping Characterization Of Additively Manufactured Airfoil Components, Andrew W. Goldin
Theses and Dissertations
The push for low cost and higher performance/efficient turbine engines have introduced a new demand for novel technologies to improve robustness to vibrations resulting in High Cycle Fatigue (HCF). There have been many proposed solutions to this, some passive and some active. With the advent of Additive Manufacturing (AM), new damping techniques can now be incorporated directly into the design and manufacture process to suppress the vibrations that create HCF. In this study, this novel unfused pocket damping technology is applied to a blade structure and the resulting damping effectiveness is quantified. The application of this technology to complex geometries …
Solution Anneal Heat Treatments To Enhance Mechanical Performance Of Additively Manufactured Inconel 718, David J. Newell
Solution Anneal Heat Treatments To Enhance Mechanical Performance Of Additively Manufactured Inconel 718, David J. Newell
Theses and Dissertations
The nickel-based superalloy Inconel 718 (IN718) is an excellent candidate among aerospace alloys for laser powder-bed fusion (LPBF) manufacturing. As-built LPBF IN718 has a vertically aligned columnar (001) microstructure which translates into orthotropic mechanical behavior. The post-process heat treatments for IN718 were developed 60 years ago for wrought and cast processes and do not mitigate the columnar microstructure of the LPBF process. Recrystallization is required to remove the columnar microstructure, which would allow for parts to be fabricated on different machines or in different orientations but still achieve the same properties. This research investigated the microstructure of LPBF IN718 as …
Analysis Of Additively Manufactured Rings Under Compression Loading For Use In A Vacuum Lighter Than Air Vehicle Structure, Kevin D. Greenoe
Analysis Of Additively Manufactured Rings Under Compression Loading For Use In A Vacuum Lighter Than Air Vehicle Structure, Kevin D. Greenoe
Theses and Dissertations
A Vacuum Lighter Than Air Vehicle (VLTAV) utilizes a lightweight structure paired with an internal vacuum to achieve buoyancy; this allows it to float through-out a given atmosphere. The pressure differential between the internal vacuum andexternal atmosphere places the vehicle under intense loading. A specific structure under investigation is the celestial icosahedron, which features nine intersecting rings that have an outer diameter of 0.2032m and circular cross-sectionalthickness of 5.08mm.The celestials rings are positioned in three different orientations and are analyzed both experimentally and analytically.
Design, Development, And Testing Of A Low Cost, Additively-Manufactured, Centrifugal Compressor, Aaron P. Bauer
Design, Development, And Testing Of A Low Cost, Additively-Manufactured, Centrifugal Compressor, Aaron P. Bauer
Theses and Dissertations
The three objectives of this research were to: 1.) design, build, and test AM compressors to substitute into COTS micro-gas turbine engines, 2.) provide initial correlations between FEA and compressor failure speed, and 3.) characterize the effects of AM on compressor performance. These goals improved the design cycle cost and the design-validation time cycle. ULTEM 9085, 300-AMB, and Onyx-Kevlar temperature-dependent tensile properties were measured. FEA-predicted failure speeds of stock compressor designs led design improvements, potentially fulfilling the original compressor requirements. Physical testing of the stock and ULTEM 9085 compressors occurred. Comparing these compressors' performances demonstrated that low cost, AM materials …
An Analysis Of The Viability Of 3d-Printed Construction As An Alternative To Conventional Construction Methods In The Expeditionary Environment, Jeneé A. Jagoda
An Analysis Of The Viability Of 3d-Printed Construction As An Alternative To Conventional Construction Methods In The Expeditionary Environment, Jeneé A. Jagoda
Theses and Dissertations
Conventional construction is believed by some to have reached its technological limit of performance, making it increasingly difficult for conventional construction methods to meet the U.S. military’s core standards of quality, cost, and timeliness in the expeditionary environment. While still in its infancy, 3D-printed construction has the potential to revolutionize the way the military performs construction in deployed environments. This research conducts a systematic review of the viability of 3D-printed construction to investigate whether or not it is now or could be a viable replacement for conventional construction methods, specifically in remote environments where conventional construction capability may be limited. …