Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 6 of 6
Full-Text Articles in Engineering
Mems Variable Area Capacitor For Room Temperature Electrometry, George C. Underwood, Tod V. Laurvick
Mems Variable Area Capacitor For Room Temperature Electrometry, George C. Underwood, Tod V. Laurvick
Faculty Publications
This paper introduces a new way to detect charge using MEMS variable capacitors for extremely sensitive, room temperature electrometry. It is largely based on the electrometers introduced by Riehl et al. [1] except variable capacitance is created by a changing area, not a changing gap. The new scheme will improve MEMS electrometers by eliminating the effects of squeeze-film damping and by theoretically increasing the maximum charge resolution by 70%. The charge conversion gain (the increase in output voltage per input unit charge) for this system is derived. The result show good agreement with MATLAB calculations.
Pvdf-Trfe Electroactive Polymer Mechanical-To-Electrical Energy Harvesting Experimental Bimorph Structure, William G. Kaval, Robert A. Lake, Ronald A. Coutu Jr.
Pvdf-Trfe Electroactive Polymer Mechanical-To-Electrical Energy Harvesting Experimental Bimorph Structure, William G. Kaval, Robert A. Lake, Ronald A. Coutu Jr.
Faculty Publications
Research of electrostrictive polymers has generated new opportunities for harvesting energy from the surrounding environment and converting it into usable electrical energy. Electroactive polymer (EAP) research is one of the new opportunities for harvesting energy from the natural environment and converting it into usable electrical energy. Piezoelectric ceramic based energy harvesting devices tend to be unsuitable for low-frequency mechanical excitations such as human movement. Organic polymers are typically softer and more flexible therefore translated electrical energy output is considerably higher under the same mechanical force. In addition, cantilever geometry is one of the most used structures in piezoelectric energy harvesters, …
Thermal Management Using Mems Bimorph Cantilever Beams, Ronald A. Coutu Jr., Robert S. Lafleur, John P. Walton, Laverne A. Starman
Thermal Management Using Mems Bimorph Cantilever Beams, Ronald A. Coutu Jr., Robert S. Lafleur, John P. Walton, Laverne A. Starman
Faculty Publications
This paper examines a passive cooling technique using microelectromechanical systems (MEMS) for localized thermal management of electronic devices. The prototype was designed using analytic equations, simulated using finite element methods (FEM), and fabricated using the commercial PolyMUMPs™ process. The system consisted of an electronic device simulator (EDS) and MEMS bimorph cantilever beams (MBCB) array with beams lengths of 200, 250, and 300 μm that were tested to characterize deflection and thermal behavior. The specific beam lengths were chosen to actuate in response to heating associated with the EDS (i.e. the longest beams actuated first corresponding to the hottest portion of …
Variable Response Of A Thermally Tuned Mems Pressure Sensor, Robert A. Lake, Ronald A. Coutu Jr.
Variable Response Of A Thermally Tuned Mems Pressure Sensor, Robert A. Lake, Ronald A. Coutu Jr.
Faculty Publications
A typical microelectromechanical systems (MEMS) pressure sensor consists of a thin, deformable membrane and sensing element such as a piezoresistive element which is used to measure the amount of deflection in response to an applied pressure. Previous efforts demonstrated that buckled membranes, from silicon on insulator (SOI) wafers, can be thermally tuned via joule heating. By applying heat to the membrane through a resistive heating element, compressive stress is induced in the membrane causing it to buckle further out of plane and increasing its overall stiffness response. It is demonstrated that by increasing the stiffness of the membrane, the response …
Improved Sensitivity Mems Cantilever Sensor For Terahertz Photoacoustic Spectroscopy, Ronald A. Coutu Jr., Ivan R. Medvedev, Douglas T. Petkie
Improved Sensitivity Mems Cantilever Sensor For Terahertz Photoacoustic Spectroscopy, Ronald A. Coutu Jr., Ivan R. Medvedev, Douglas T. Petkie
Faculty Publications
In this paper, a microelectromechanical system (MEMS) cantilever sensor was designed, modeled and fabricated to measure the terahertz (THz) radiation induced photoacoustic (PA) response of gases under low vacuum conditions. This work vastly improves cantilever sensitivity over previous efforts, by reducing internal beam stresses, minimizing out of plane beam curvature and optimizing beam damping. In addition, fabrication yield was improved by approximately 50% by filleting the cantilever’s anchor and free end to help reduce high stress areas that occurred during device fabrication and processing. All of the cantilever sensors were fabricated using silicon-on-insulator (SOI) wafers and tested in a custom …
Performance Comparison Of Pb(Zr0.52Ti0.48)O3-Only And Pb(Zr0.52Ti0.48)O3-On-Silicon Resonators, Hengky Chandrahalim, Sunil A. Bhave, Ronald G. Polcawich, Jeff Pulskamp, Dan Judy, Roger Kaul, Madan Dubey
Performance Comparison Of Pb(Zr0.52Ti0.48)O3-Only And Pb(Zr0.52Ti0.48)O3-On-Silicon Resonators, Hengky Chandrahalim, Sunil A. Bhave, Ronald G. Polcawich, Jeff Pulskamp, Dan Judy, Roger Kaul, Madan Dubey
Faculty Publications
This paper provides a quantitative comparison and explores the design space of lead zirconium titanate (PZT)–only and PZT-on-silicon length-extensional mode resonators for incorporation into radio frequency microelectromechanical system filters and oscillators. We experimentally measured the correlation of motional impedance (RX) and quality factor (Q) with the resonators’ silicon layer thickness (tSi). For identical lateral dimensions and PZT-layer thicknesses (tPZT), the PZT-on-silicon resonator has higher resonant frequency (fC), higher Q (5100 versus 140), lower RX (51 Ω versus 205 Ω), and better linearity [third-order input intercept …