Engineering Commons^™

Modeling, Simulation, And Validation Of Process-Structure-Property Relationships In Fused Filament Fabrication, Aaron Grant

Electronic Theses and Dissertations

As additive manufacturing (AM) grows in popularity, the need for better simulation tools to predict the process-structure-property relationships of AM parts becomes ever more necessary to employ the technology in design of functional parts with varying degrees of complexity and performance requirements. Many simulation tools and techniques have been developed that aim to achieve this goal, and the main purpose of this research is to explore how well different simulation tools and modeling approaches can capture various AM-specific features such as inter-raster and end-of raster voids, and residual stresses induced by dissimilar rates of thermal expansion. Process simulation of fused …

Axial Compressor Based On Plastic Additive Manufacturing, Chris Phu

Mechanical Engineering Undergraduate Honors Theses

Turbomolecular pumps designed to function in very low pressures tend to be too prohibitively expensive for student researchers. On the other hand, while conventional pumps are affordable, they can’t function in extreme low pressures. An additively manufactured axial compressor however is inexpensive to manufacturer and only needs to be build up enough pressure for a conventional pump to function. After many design iterations, a final iteration that is near vacuum chamber ready has been 3D printed and tested for spin functionally. The designed axial compressor is easy to assemble and very modular. Conclusions from each of the design iterations is …

Durability Of Hybrid Large Area Additive Tooling For Vacuum Infusion Of Composites, Nathan Joseph Northrup

Theses and Dissertations

The purpose of this research was to scientifically validate potential cost-saving measures for production of large area additively manufactured tooling for vacuum infusion of composites. These cost saving measures included using a hybrid additive/subtractive manufacturing system to fabricate the mold, requiring lower capital cost and creating shorter lead times. Fiberglass reinforcement was used instead of carbon in the mold material. The validation was done by designing and fabricating a mold for a custom test artifact and analyzing the surface geometry over the course of multiple infusions until tool failure.After printing and machining, the mold required a sealer in order to …

Application Of Solar Water Heaters For Industrial Use, Lucas T. Atkins

Theses and Dissertations

Solar water heating is a technology that is mainly used for domestic water heating in residential homes. In most applications, the idea is to make a home “off the grid” in that there is no requirement for outside infrastructure or need for energy utility to provide power to this home. This falls in line with the trend of “going green” in an effort to reduce energy use, increase efficiency, or reduce emissions and other harmful byproducts.

This technology can be adapted to reduce the energy costs of industrial manufacturing plants. By eliminating the need for certain sections of a process …

Fiberglass Mat-Roll Carryover, Bryce Youngson, Aaliyah Ramos, Johann Cayaban, Tony Ledesma

Mechanical Engineering

The asphalt shingle is a type of roof shingle that uses asphalt for waterproofing. Its low cost and easy installation make it one of the most common roof covers in North America. General Aniline and Film (GAF) is one of the nation’s largest manufacturers of roofing materials and produces asphalt shingles at their Shafter, California manufacturing facility. To manufacture asphalt shingles, a base material of fiberglass passes through a series of processes that sequentially add asphalt, ceramic-coated mineral granules, and thermoplastic adhesive. The fiberglass base-material arrives at the manufacturing facility in large rolls that workers must periodically splice together in …

Maquiladoras In Central America: An Analysis Of Workforce Schedule, Productivity And Fatigue., Jose L. Barahona

Masters Theses & Specialist Projects

Textile factories or Maquiladoras are very abundant and predominant in Central American economies. However, they all do not have the same standardized work schedule or routines. Most of the Maquiladoras only follow schedules and regulations established by the current labor laws without taking into consideration many variables within their organization that could affect their overall performance. As a result, the purpose of the study is to analyze the current working structure of a textile Maquiladora and determine the most suitable schedule that will abide with the current working structure but also increase production levels, employee morale and decrease employee fatigue. …

Development Of An Automated Fiber Placement Process For The Fabrication Of Thermoplastic Composite Laminates, Anthony M. Sabido

Theses and Dissertations

An automated fiber placement process is desired for manufacturing variable-stiffness thermoplastic composite laminates. By developing such a composite laminate, it is possible to take advantage of the tunable performance increases that are achievable by spatially steering individual tows. In addition, using a thermoplastic polymer as the matrix material has many advantages: a high toughness, ability to employ thermoplastic joining processes that do not require adhesives, long storage life, and lacks the need to be refrigerated. This process was experimentally developed, where the effect of various process parameters on the quality of the laminate were evaluated. An experimental AFP head was …

Fluid Power Vehicle Challenge - The Incompressibles - Final Design Report, Nicholas Gholdoian, Russell Posin, David Vitt, Alex Knickerbocker, Kyle Franck, Julian Rodkiewicz

Mechanical Engineering

This report provides a comprehensive description of the research, analysis and design work that The Incompressibles have completed thus far in the senior project process. This document includes all the work that The Incompressibles have completed for the team’s Preliminary Design Review (PDR), Critical Design Review (CDR), the work leading up to the 2019 FPVC competiton and the competition results. This report includes the initial research that the team completed for the fluid power competition, first iterations of designs, final iterations of designs, manufacturing results and processes, and finally testing and results from competition. With a new design for the …

High Strollers, Braeden Hammond, Morley Perrin, Reid Bartels, Juan Rodriguez

Mechanical Engineering

This report documents the final product of Jonathon’s new lightweight stroller. The Mechanical Engineering team from Cal Poly, High Strollers, began the project to create a lightweight stroller for the project sponsor, Nina Aguayo, and her son, Jonathon Aguayo, in Fall of 2018. Jonathon is diagnosed with Delayed Brain Development and Hypotonia with some characteristics of Cerebral Palsy. He has a 50lb high intensity stroller to go to and from school. Mrs. Aguayo needed a stroller that is easier to transport while still meeting all of Jonathon’s needs. The re-designed stroller will make leisurely outings for Mrs. Aguayo and Jonathon …

Universal Bike Suspension Design, Ernesto Huerta, Gregory Ryan Ritter, Chris Michael Fedor, Michael Wu

Mechanical Engineering

Cal Poly Bike Builders (CPBB) is a student club at Cal Poly helping students design and fabricate their own bicycles. Currently, club members build rigid frames and mountain bikes with only front-suspension–commonly referred to as a “hardtail”. As more students join the club, interest grows in building full-suspension mountain bikes (FSMTB). Designing and manufacturing a mountain bike rear-suspension system requires a diverse skillset and a substantial time commitment. As a result, individual efforts building FSMTB have proven unsuccessful. The scope of this project is to develop a defined method and necessary tools such that all CPBB members can efficiently build …

Increasing Operator Skills In A Manufacturing Environment, Bobbie Lee Hubbard

Instructional Design Capstones Collection

A plastic-injection molding facility is converting many machines into more automated systems. These complex systems require higher-level skill sets than current operators have been trained in. There is a need to increase the level of competency in most, if not all, of the operators at the Facility, and create a system of levels that engages employees and encourages learning new skills to increase their position and pay.

There is a need for a clear path of compensation based on skills and actions. The Facility is currently not optimizing or maximizing their current portfolio of machines and resources, leaving an unknown …

Investigation Of Design, Manufacture, Analysis, And Test Of A Composite Connecting Rod Under Compression, Thomas Juhl Rohrbach

Master's Theses

Composite materials hold great potential for the replacement of traditional materials in machines utilized on a daily basis. One such example is within an engine block assembly where massive components inherently reduce the efficiency of the system they constitute. By replacing metal elements such as connecting rods, cylinder caps, or a crank shaft with composite alternatives, a significant increase in performance may be achieved with respect to mechanical strength, thermal stability, and durability, while also reducing mass. Exploration of this technology applied to a connecting rod geometry was investigated through a combination of process development, manufacturing, numerical analysis and testing. …

A Systematic Study On The Effects Of Dimensional And Materials Tolerances On Permanent Magnet Synchronous Machines Based On The Ieee Std 1812, Narges Taran, Vandana Rallabandi, Dan M. Ionel, Ping Zhou, Mark Theile, Greg Heins

Power and Energy Institute of Kentucky Faculty Publications

In the process of designing and manufacturing an electrical machine, a systematic study of dimensional and material tolerances is of the utmost importance. This paper proposes a systematic method by which the effect of design specification variations on permanent magnet (PM) synchronous machine performance may be identified and quantified. The method combines design of experiments techniques, open-circuit and short-circuit physical measurements, and virtual test simulations conducted based on the recently approved IEEE Std 1812 testing guide. Three case studies, two provided by a spoke-type PM radial field machine configuration, in two designs with different electromagnetic loading, and an axial flux …

Development Of A Closed Car-T Manufacturing Process, Loo-Yong Steven Kee, Calley Hirsch, Devina Ramsaroop, Elizabeth Csaszar, Danylo Sirskyj, Aaron Dulgar-Tulloch

Advancing Manufacture of Cell and Gene Therapies VI

The field of immunotherapy has emerged as a promising new type of treatment for cancer with the approval of the first two CAR-T therapies. The clinical success of T-cell based immunotherapies necessitates a robust manufacturing process for these products to be consistently produced at commercial scale. Our CAR-T workflow combines unit operation specific solutions for thaw of an apheresis unit, wash, CD3 selection, T-cell activation, lentiviral transduction, incubator- and reactor-based expansion culture, harvest, formulation, cryopreservation and thaw of CAR-T product. We have evaluated the impact of both serum-containing and xeno-free culture media, commercially available T-cell selection and activation reagents, closed …

Stair Climbing Hand Truck, James Mcpherson

All Undergraduate Projects

Abstract

Getting a heavy object up a flight of stairs usually requires a team of two or more people. Even with a team of people, the task is often still difficult, dangerous, and possibly insurmountable by one person. This problem is especially prevalent in for those who are moving into apartment complexes. Most apartment complexes have many buildings with two or more floors of living quarters, and elevators are often missing. This project sought to offer a solution to this problem. The solution in question; a motorized hand-truck with 2, trigonal planar pinwheels in place of the stock wheels. The …

Process Sustainability Evaluation For Manufacturing Of A Component With The 6r Application, Ana E. Bonilla Hernández, Tao Lu, Tomas Beno, Claes Fredriksson, Ibrahim S. Jawahir

Institute for Sustainable Manufacturing Faculty Publications

Sustainability in manufacturing can be evaluated at product, process and system levels. The 6R methodology for sustainability enhancement in manufacturing processes includes: reduced use of materials, energy, water and other resources; reusing of products/components; recovery and recycling of materials/components; remanufacturing of products; and redesigning of products to utilize recovered materials/resources. Although manufacturing processes can be evaluated by their productivity, quality and cost, process sustainability assessment makes it a complete evaluation. This paper presents a 6R-based evaluation method for sustainable manufacturing in terms of specific metrics within six major metrics clusters: environmental impact, energy consumption, waste management, cost, resource utilization and …

Developing A Commercial Product Using A Consumer Grade 3d Printer, Calvin Smith

All Graduate Theses, Dissertations, and Other Capstone Projects

The development of affordable, quality, consumer grade 3D printers has allowed entrepreneurs to develop new products and start small businesses. As the print quality of consumer grade printers has improved entrepreneurs have been able to develop consumer quality products without the traditional expense of mass manufacturing. This change from mass manufacturing to small scale and custom production has allowed for the growth of small businesses. Websites such as www.etsy.com show hundreds of small businesses based on 3D printing, these businesses showcase thousands of products ranging from useful household items to cosplay. This thesis covers the process of a small business …

3d Scaffolds Of Polycaprolactone/Copper-Doped Bioactive Glass: Architecture Engineering With Additive Manufacturing And Cellularassessments In A Coculture Of Bone Marrow Stem Cells And Endothelial Cells, Xiaoju Wang, Binbin Zhang, Sanna Pitkanen, Miina Ojansivu, Chunlin Xu, Markus Hannula, Jari A. Hyttinen, Susanna S. Miettinen, Leena Hupa, Gordon G. Wallace

Australian Institute for Innovative Materials - Papers

The local delivery of Cu2+ from copper-doped bioactive glass (Cu-BaG) was combined with 3D printing of polycaprolactone (PCL) scaffolds for its potent angiogenic effect in bone tissue engineering. PCL and Cu-BaG were, respectively, dissolved and dispersed in acetone to formulate a moderately homogeneous ink. The PCL/Cu-BaG scaffolds were fabricated via direct ink writing into a cold ethanol bath. The architecture of the printed scaffolds, including strut diameter, strut spacing, and porosity, were investigated and characterized. The PCL/Cu-BaG scaffolds showed a Cu-BaG content-dependent mechanical property, as the compressive Young's modulus ranged from 7 to 13 MPa at an apparent porosity of …