Engineering Commons^™

Rf Front End For An Integrated Silhouette Capture And Boundary Detection Frequency Modulated Continuous Wave Ultra-Wideband Radar System For The Extension Of Independent Living, Adrian Smet

Master's Theses

Limitations of current eldercare monitoring systems leave a need for new solutions. A monitoring system based on a frequency modulated continuous wave ultra-wideband short-range radar is proposed for this application. The complete proposed monitoring system is comprised of four blocks: boundary detection, silhouette capture, human identification, and data transmission. This paper develops the RF front end hardware for the silhouette capture subsystem.

System requirements are derived for the silhouette capture subsystem. An architecture for the RF front end is designed, and required individual component specifications are determined. Components are selected off the shelf or custom designed for each socket. Full …

Two Senior Projects: 2.4 Ghz, 40% Efficiency Radio Frequency Amplifier, Ieee Design Contest, & Design And Implementation Of A Software Costas Loop For Audio Frequencies, Robert J. Tong

Electrical Engineering

How to Read this Document:

This document combines two senior project reports. The first senior project documents designing a class AB RF amplifier. The second, discusses the design and implementation of a software Costas loop for audio frequencies. The first report begins on the next page, while the Costas loop report starts on page 24. The two reports are orthogonal from one another. It is not a prerequisite to read the RF amplifier report before reading the Costas loop report. This document is merely two reports combined into one document. The second report, about the Costas loop, was written as …

The Following Robot, Juan D. Cerda, Matthew S. Kwan, Vi M. Le

Computer Engineering

The objective of this project is to design, build, and test an autonomous robot with an associated Android application. The robot uses on board inertial measurement sensors (magnetometer, accelerometer, gyroscope) and coordinates itself through Bluetooth communication with the similar built­in measurement sensors on the Android phone to mimic and follow movement. The Following Robot incorporates the same basic movement functionality as a typical RC car. The robot follows the user’s phone through an application on one’s phone. This application accesses the phone’s accelerometer and gyroscope data and translates into appropriate conversions. Methods of tracking and calculating distance or angular displacement …

Wireless Communication For Greenhouse Environment, Chris J. Lambert, Dean T. Lockman, Ian A. Nielsen

Electrical Engineering

Modern day population growth and global climate change requires high-yield agricultural systems that can function in harsh environments. Greenhouses can maintain temperature and humidity, while serving as a protective, nurturing alternative to vulnerable farm environments. With weather effects eliminated, greenhouses provide productive environments for experimental agriculture techniques such as hydroponics and aquaculture. These methods of agriculture, specifically aquaculture, require constant monitoring. The failure of electronic devices such as an air pump prove fatal to a fish population in a short time frame. In developing countries, agricultural locations may be a significant distance from a farmer’s home, with no internet or …

Investigation Of Mimo Communications, Rodrigo Mendez Olea, William C. Tran, Patrick C. Kezer, Jean M. Whitmore

Electrical Engineering

This project focuses on the background of multiple input multiple output (MIMO) communication and its advantages over the other possible implementations. A background of wireless communication in regards to modulation types, information theory, antenna background and a hardware implementation using a VSA and VSG is provided. The theory is compared and verified with the hardware implementation with regards to the effect of the increase in the number of antennas and the parameter vector error magnitude.

Hands On, Michael Le, Justin Remulla, Chris Menezes, Noah Beilin

Electrical Engineering

The goal is to design an extremely articulate smart glove, which acts a virtual reality controller. The smart glove will have gesture detection, which could include hand movements and/or combinations of finger movements to emulate mouse click or scroll, or digitally map out a hand for integrations with virtually reality softwares. This glove will have multiple accelerometer sensors on each finger and joint, connected to a single board running BLE MCU SoC in order to communicate with computer or mobile devices. The glove would connect to devices such as computers or phones using a Bluetooth dongle with applications in virtual …

Remote Cable Gantry, Allen L. Bailey

Electrical Engineering

The Remote Cable Gantry is a robotic system that was initially intended to aid in the art of aerial videography. It was designed to enable novice and expert users alike to capture both video footage and audio from perspectives unachievable by current methods. This system uses a series of cables to control the position of a camera gimbal in a defined 3D space and, as a self-contained unit, is portable and easy to use. The Remote Cable Gantry offers a quiet, intuitive, and safe alternative to existing technology, which has been limiting the market and potential of aerial photography and …

Verification Of Receiver Equalization By Integrating Dataflow Simulation And Physical Channels, David M. Ritter, Tina Smilkstein

Master's Theses

This thesis combines Keysight’s SystemVue software with a Vector Signal Analyzer (VSA) and Vector Signal Generator (VSG) to test receiver equalization schemes over physical channels. The testing setup, “Equalization Verification,” is intended to be able to evaluate any equalization scheme over any physical channel, and a decision-directed feed-forward LMS equalizer is used as an example. The decision-directed feed-forward LMS equalizer is shown to decrease the BER from 10^-2 to 10^-3 (average of all trials) over a CAT7 and CAT6A cable, both simulated and physical, for 1GHz and 2GHz carrier, and 80MHz data rate. A wireless channel, 2.4GHz Dipole …

Estimating Transit Ridership Patterns Through Automated Data Collection Technology: A Case Study In San Luis Obispo, California, Ashley Kim

Master's Theses

Public transportation offers a crucial solution to the travel demand in light of national and global economic, energy, and environmental challenges. If implemented effectively, public transit offers an affordable, convenient, and sustainable transportation mode. Implementation of new technologies for information-harvesting may lead to more effective transit operations. This study examines the potential of automated data collection technologies to analyzing and understand the origin-destination flow patterns, which is essential for transit route planning and stop location placement.

This thesis investigates the collection and analysis of data of passengers onboard San Luis Obispo Transit buses in February and March 2017 using Bluetooth …

Complex Filters As Cascade Of Buffered Gingell Structures: Design From Band-Pass Constraints, Nicole M. Hay

Master's Theses

Complex filters are multi-input, multi-output networks designed to discriminate based upon the relative phase difference between input signals. Complex filters find application in modern wireless systems for single sideband transmission and image-reject reception. This thesis presents one active complex filter implementation using two operational amplifiers per stage, termed “type-II” topology. The “type-II” originates from the passive RC-CR polyphase topology presented by Gingell in his 1973 paper, “Single sideband modulation using sequence asymmetric polyphase networks.” This new topology gains several advantages over existing complex filter implementations, namely “cascadability” (multiple sections placed in series to create a higher-order response) without altering the …

Uhf Rfid Antenna Impedance Matching Techniques, Kamron Sockolov

Master's Theses

Radio Frequency Identification (RFID) systems use electromagnetic signals to wirelessly identify and track RFID-tagged objects. A reader transmits a carrier wave request signal to an RFID tag, which then transmits a unique identification signal back to the reader. Applications include supply chain inventory management, automated toll booth fee systems, sports event timing, restricted access control, pet monitoring and retail theft prevention. An RFID tag includes an antenna connected to a Radio Frequency Integrated Circuit (RFIC). RFID tags in the ultra-high frequency (UHF), industrial, scientific and medical (ISM) 902-928MHz band and global Electronic Product Code (EPC) 860‑960MHz band are powered passively …

Thermal Evolution Of Moon, Arshdeep Singh Gill

Master's Theses

In August, 2014 three experiments were conducted using infrared systems deployed at White Mountain Research center, CA. The data was acquired for the whole month of August. Teams of 3-4 students from Cal Poly San Luis Obispo and UC Santa Barbara were stationed at the research center for 2-3 days to operate the equipment. The three experiments were:(1) creating spatial-temporal time series of lunar surface temperatures;(2) identifying atmospheric meteor trails;(3) search for meteor impacts on the Moon surface. Out of the three this thesis focusses on experiment 1 and the results from this experiment could also help with the other …