Engineering Commons^™

The Microstructure And The Electrochemical Behavior Of Cobalt Chromium Molybdenum Alloys From Retrieved Hip Implants, Christopher P. Emerson

FIU Electronic Theses and Dissertations

Because of their excellent mechanical, tribological, and electrochemical properties, Cobalt Chromium Molybdenum alloys have been used as the material for both the stem and head of modular hip implants. Corrosion is one mechanism by which metal debris, from these implants, is generated, which can lead to adverse events that requires revision surgery. Manufacturing process such as wrought, as-cast, and powder metallurgy influences the microstructure, material properties, and performance of these implants

The current research focuses on analyzing the microstructure of CoCrMo alloys from retrieved hip implants with optical and scanning electron microscopy. Additionally, energy disperse spectroscopy was utilized to determine …

Reference Diffraction Patterns, Microstructure, And Pore-Size Distribution For The Copper (Ii) Benzene-1,3,5-Tricarboxylate Metal Organic Framework (Cu-Btc) Compounds, L. Li, I. Williamson

Materials Science and Engineering Faculty Publications and Presentations

No abstract provided.

Producing High Strength Aluminum Alloy By Combination Of Equal Channel Angular Pressing And Bake Hardening, Hamid Alihosseini, Mohsen Asle Zaeem, Kamran Dehghani, Ghader Faraji

Materials Science and Engineering Faculty Research & Creative Works

A combination of severe plastic deformation by equal channel angular pressing (ECAP) and bake hardening (BH) was used to produce high strength ultrafine-grained AA6061 aluminum alloy. 2, 4 and 8 passes of ECAP were performed, and the bake hardenability of samples was tested by 6% pre-straining followed by baking at 200 °C for 20 min. The microstructures obtained for various passes of ECAP were characterized by XRD, EBSD, and TEM techniques. The microstructures were refined from an average grain size of 20 µm to 212 nm after 8 passes of ECAP. Maximum bake hardenability of 110 MPa, and final yield …

Piezoelectric Poly(Vinylidene Fluoride) Microstructure And Poling State In Active Tissue Engineering, Clarisse Ribeiro, Daniela M. Correia, S Ribeiro, Vitor Sencadas, Gabriela Botelho, Senentxu Lanceros-Méndez

Faculty of Engineering and Information Sciences - Papers: Part A

Tissue engineering strategies rely on suitable membranes and scaffolds, providing the necessary physicochemical stimuli to specific cells. This review summarizes the main results on piezoelectric polymers, in particular poly(vinylidene fluoride), for muscle and bone cell culture. Further, the relevance of polymer microstructure and surface charge on cell response is demonstrated. Together with the necessary biochemical cues, the proper design of piezoelectric polymers can open the way to novel and more reliable tissue engineering strategies for cells in which electromechanical stimuli are present in their environment.

The Effects Of Vacuum Annealing Temperatures On The Microstructure, Mechanical Properties And Electrical Resistivity Of Mg-3al-1zn Alloy Ribbons, Fenghua Chen, Qingxue Huang, Zhengyi Jiang, Jingwei Zhao, Binyu Sun, Yugui Li

Faculty of Engineering and Information Sciences - Papers: Part A

This paper investigates the influence of vacuum annealing temperature on the microstructure, mechanical properties and electrical resistivity of Mg-3Al-1Zn rapid solidification (RS) magnesium ribbons. The results indicate that when the annealing temperature is increased, the grain size of the ribbons is dramatically reduced from 10 to 1 μm. The highest break stress and micro-hardness is obtained at 673 K. These effects are ascribed to the dispersion strengthening caused by the high amount of fine nanoparticles distributed in the material. Electrical resistivity-temperature (ρ-T) curves have been used to provide useful information about the effects of the annealing temperature on the grain …

Effect Of Pre-Quenching Process On Microstructure And Mechanical Properties In A Nb-Microalloyed Low Carbon Q-P Steel, Jun Zhang, Hua Ding, Jingwei Zhao

Faculty of Engineering and Information Sciences - Papers: Part A

A refined microstructure consisting of martensite and retained austenite at room temperature has been produced in a Nb-microalloyed low carbon Si-Mn steel by a novel heat-treatment, pre-quenching prior to quenching and partitioning processes (Q&Q-P). The results showed that compared with the conventional quenching and partitioning steel the mechanical properties of steel obtained by the novel treatment have been significantly improved, with a good combination of ultimate tensile strength (1000MPa) and total elongation (above 30%). Meanwhile, the volume fraction of retained austenite has been increased. It was found that the improvement of mechanical properties was mainly attributed to the enhanced TRIP …

Effect Of Temperature On Microstructure And Deformation Mechanism Of Fe-30mn-3si-4al Twip Steel At Strain Rate Of 700 S-1, Zhiping Xiong, Xue-Ping Ren, Jian Shu, Zhe-Lei Wang, Wei-Ping Bao, Shu-Xia Li

Faculty of Engineering and Information Sciences - Papers: Part A

As twinning-induced plasticity (TWIP) steel is one potential material for shaped charge liner due to the combination of high strength and high plasticity, deformation mechanism at high strain rate and high temperature is required to study. Compression experiments of Fe-30Mn-3Si-4Al TWIP steel were conducted using a Gleeble-1500 thermal simulation machine and a split-Hopkinson pressure bar (SHPB) between 298 and 1073 K at strain rates of 10-3 and 700 s-1, respectively. Microstructures were observed using optical microscopy (OM) and transmission electron microscopy (TEM). Results show that flow stress and densities of deformation twins and dislocations decrease with increasing deformation temperature at …

Microstructure Evolution During Isochronal Annealing Of A 42% Cold Rolled Trip-Twip Steel, Sudipta Pramanik, Ahmed A. Saleh, Dagoberto Brandao Santos, Elena V. Pereloma, Azdiar A. Gazder

Faculty of Engineering and Information Sciences - Papers: Part A

A high manganese TRIP-TWIP steel was cold rolled to 42% thickness reduction and isochronally annealed between 600 to 900 °C for 300 s. The microstructural evolution during annealing was studied by high resolution electron back-scattering diffraction. After cold rolling, the steel comprised predominant fraction of α′-martensite, a small fraction of blocky ε-martensite and a trace fraction of retained austenite (γ). During annealing, the reversion of ε and α′ martensite to γ was followed by the recrystallisation of γ. While the processes of reversion to and recrystallisation of γ were completed by 700 °C, further annealing between 750 to 900 °C …