Open Access. Powered by Scholars. Published by Universities.®
- Discipline
Articles 1 - 30 of 34
Full-Text Articles in Engineering
Microstructures Of Conducting Polymers: Patterning And Actuation Study, Babita Gaihre, Bo Weng, Syed A. Ashraf, Geoffrey M. Spinks, Peter C. Innis, Gordon G. Wallace
Microstructures Of Conducting Polymers: Patterning And Actuation Study, Babita Gaihre, Bo Weng, Syed A. Ashraf, Geoffrey M. Spinks, Peter C. Innis, Gordon G. Wallace
Australian Institute for Innovative Materials - Papers
The conducting polymers exhibit electrochemically driven expansion and shrinkage due to ingress and egress of dopant ions in response to potential applied. In this paper, we report on patterning of microdots and microsquares of polypyrrole (PPy), poly(3,4-ethylenedioxythiophene) (PEDOT) and poly(3,3-dihexyl-3-4-dihydro-2H-thieno[3,4b][1,4]-dioxepine PProDOT(Hx) 2 and their behaviour under voltage change. Stainless steel mesh was used to deposit microdots and inkjet-printed cellulose girds were used to deposit microsqures of the conducting polymers on the ITO surface. It was found that PPy showed distinct actuation in the z direction while colour change was prominent in the case of PEDOT and PProDOT(Hx)2.
N-Nitrosamine Rejection By Reverse Osmosis Membranes: A Full-Scale Study, Takahiro Fujioka, Stuart J. Khan, James A. Mcdonald, Annalie Roux, Yvan Poussade, Jorg E. Drewes, Long D. Nghiem
N-Nitrosamine Rejection By Reverse Osmosis Membranes: A Full-Scale Study, Takahiro Fujioka, Stuart J. Khan, James A. Mcdonald, Annalie Roux, Yvan Poussade, Jorg E. Drewes, Long D. Nghiem
SMART Infrastructure Facility - Papers
This study aims to provide longitudinal and spatial insights to the rejection of N-nitrosamines by reverse osmosis (RO) membranes during sampling campaigns at three full-scale water recycling plants. Samples were collected at all individual filtration stages as well as at a cool and a warm weather period to elucidate the impact of recovery and feed temperature on the rejection of N-nitrosamines. N-nitrosodimethylamine (NDMA) was detected in all RO feed samples varying between 7 and 32 ng/L. Concentrations of most other N-nitrosamines in the feed solutions were determined to be lower than their detection limits (3e5 ng/L) but higher concentrations were …
A Study On The Suitability Of Cable Models To Simulate Switching Transients In A 132 Kv Underground Cable, Muhamad Zalani Daud, P Ciufo, S Perera
A Study On The Suitability Of Cable Models To Simulate Switching Transients In A 132 Kv Underground Cable, Muhamad Zalani Daud, P Ciufo, S Perera
Faculty of Engineering and Information Sciences - Papers: Part A
Switching transients resulting from the energisation of high voltage cable systems may have a significant effect on both the cables being switched as well as the power system components in the vicinity. The impacts of these transients on such cables are measured based on the stress arising as a result of the voltage and current peaks and the frequency of oscillatory transients. These quantities are typically obtained from a simulation by using a suitable cable model, normally with the capability to predict the transient behaviour in the range up to several 10 kHz. To obtain a cable model that enables …
Impact Of Patient Rotational Errors On Target And Critical Structure Dose In Imrt: A 3d Simulation Study, S Arumugam, A Xing, P Vial, A Scotti, R Stirton, G Goozee, Lois Holloway
Impact Of Patient Rotational Errors On Target And Critical Structure Dose In Imrt: A 3d Simulation Study, S Arumugam, A Xing, P Vial, A Scotti, R Stirton, G Goozee, Lois Holloway
Faculty of Engineering and Information Sciences - Papers: Part A
The impact of 3D rotational errors in patient positioning on dose delivered target volumes and critical structures in IMRT was studied. Patient rotational errors ranging from -30 to +30 was introduced to IMRT treatment plans of pelvis, head and neck and brain treatment sites and the impact of rotational error on DVH metrics was assessed. The magnitude of impact of rotational error on the error in dose delivered to the target volume and critical structures depends on the location of the structures from plan isocentre. In studied plans, a maximum percentage difference of up to -9.8(1s=13.4) % in D95 to …
Online In Vivo Dosimetry In High Dose Rate Prostate Brchytherapy With Moskin Detectors: In Phantom Feasibility Study, G Gambarini, M Carrara, C Tenconi, N Mantaut, M Borroni, D Cutajar, M Petasecca, I Fuduli, M Lerch, E Pignoli, Anatoly B. Rosenfeld
Online In Vivo Dosimetry In High Dose Rate Prostate Brchytherapy With Moskin Detectors: In Phantom Feasibility Study, G Gambarini, M Carrara, C Tenconi, N Mantaut, M Borroni, D Cutajar, M Petasecca, I Fuduli, M Lerch, E Pignoli, Anatoly B. Rosenfeld
Faculty of Engineering and Information Sciences - Papers: Part A
MOSkin detectors were studied to perform real-time in vivo dose measurements in high dose rate prostate brachytherapy. Measurements were performed inside an urethral catheter in a gel phantom simulating a real prostate implant. Measured and expected doses were compared and the discrepancy was found to be within 8.9% and 3.8% for single MOSkin and dual-MOSkin configurations, respectively. Results show that dual-MOSkin detectors can be profitably adopted in prostate brachytherapy treatments to perform real-time in vivo dosimetry inside the urethra.
Laboratory Study On Rockbolt Corrosion, Naj Aziz, P Craig, Jan Nemcik
Laboratory Study On Rockbolt Corrosion, Naj Aziz, P Craig, Jan Nemcik
Faculty of Engineering and Information Sciences - Papers: Part A
The effect of long term exposure of full size bolts to corrosive environments is presented. A special test rig was used to test four bolts under different loading conditions. Four, X-grade identical corrosioin testing using acid sulphate water. the pH value of the curculated water varied between 3.4 and 4.3. The corrosion exposure test period lasted three and half years. Two bolts were axially loaded to 10 and 20 tonnes force respectively, the third bolt was subjected to a 360 Nm torsion load and the fourth bolt was left unstressed to act as a reference bolt. After the test period …
Parametric Study On Chain-Die Forming For Advanced High Strength Steels, Yuankun Zhang, Shichao Ding
Parametric Study On Chain-Die Forming For Advanced High Strength Steels, Yuankun Zhang, Shichao Ding
Faculty of Engineering and Information Sciences - Papers: Part A
As the applications of AHSS for the automotive industry are increasing significantly within the last decade, it becomes more and more important to develop a new forming technology as an alternative or even a replacement to roll forming to overcome the difficulties and problems of manufacturing the AHSS parts. The springback of the material with higher strength and thinner thickness becomes more difficult to predict, which directly affects the application of roll forming in AHSS. Chain-die forming, as an alternative to roll forming proposed and developed recently in Australia, is expected to be a solution to the problems addressed. It …
A Study Of Current Maintenance Strategies And The Reliability Of Critical Medical Equipment In Hospitals In Relation To Patient Outcomes, Khelood Mkalaf, Peter Gibson, John Flanagan
A Study Of Current Maintenance Strategies And The Reliability Of Critical Medical Equipment In Hospitals In Relation To Patient Outcomes, Khelood Mkalaf, Peter Gibson, John Flanagan
Faculty of Engineering and Information Sciences - Papers: Part A
This study investigates the relationship between the reliability of critical medical equipment (CME) and the effectiveness of CME maintenance management strategies in relation to patient outcomes in 84 public hospitals of a top 20 OECD country. The work has examined the effectiveness of CME maintenance management strategies used by the public hospital system of a large state run health organization. The conceptual framework was designed to examine the significance of the relationship between six variables: (1) types of maintenance management strategies, (2) maintenance services, (3) maintenance practice, (4) medical equipment reliability, (5) maintenance costs and (6) patient outcomes. The results …
Brachyview, A Novel Inbody Imaging System For Hdr Prostate Brachytherapy: Design And Monte Carlo Feasibility Study, M Safavi-Naeini, Z Han, D Cutajar, S Guatelli, M Petasecca, M L. F Lerch, D. Franklin, J Jakubek, S Pospisil, J Bucci, M Zaider, Anatoly B. Rosenfeld
Brachyview, A Novel Inbody Imaging System For Hdr Prostate Brachytherapy: Design And Monte Carlo Feasibility Study, M Safavi-Naeini, Z Han, D Cutajar, S Guatelli, M Petasecca, M L. F Lerch, D. Franklin, J Jakubek, S Pospisil, J Bucci, M Zaider, Anatoly B. Rosenfeld
Faculty of Engineering and Information Sciences - Papers: Part A
Purpose: High dose rate (HDR) brachytherapy is a form of radiation therapy for treating prostate cancer whereby a high activity radiation source is moved between predefined positions inside applicators inserted within the treatment volume. Accurate positioning of the source is essential in delivering the desired dose to the target area while avoiding radiation injury to the surrounding tissue. In this paper, HDR BrachyView, a novel inbody dosimetric imaging system for real time monitoring and verification of the radioactive seed position in HDR prostate brachytherapy treatment is introduced. The current prototype consists of a 15 × 60 mm2 silicon pixel detector …
A Joint Theoretical And Experimental Study For Elastic Electron Scattering From 1,4-Dioxane, P Palihawadana, J P. Sullivan, S J. Buckman, Z Masin, J D. Gorfinkiel, F Blanco, G Garcia, M J. Brunger
A Joint Theoretical And Experimental Study For Elastic Electron Scattering From 1,4-Dioxane, P Palihawadana, J P. Sullivan, S J. Buckman, Z Masin, J D. Gorfinkiel, F Blanco, G Garcia, M J. Brunger
Faculty of Engineering and Information Sciences - Papers: Part A
We present results of measurements and calculations of elastic electron scattering from 1,4-dioxane in the energy range of 0–1000 eV. Absolute differential and integral elastic cross sections have been measured using a crossed electron-molecule beam spectrometer and the relative flow technique, at four energies in the 10–30 eV range and for scattered electrons in the angular range 20◦–129◦. The measured cross sections are compared with results from R-matrix computations, at the static exchange plus polarization level, calculated at energies between 0–20 eV, and with calculations employing the independent atom model with the screening corrected additivity rule (IAM-SCAR). Those latter computations …
The Feasibility Study And Characterziation Of A Two-Dimensional Diode Array In “Magic Phantom” For High Dose Rate Brachytherapy Quality Assurance, A Espinoza, B Beeksma, M Petasecca, I Fuduli, C Porumb, D L. Cutajar, S Corde, M A. Jackson, M Lf Lerch, Anatoly B. Rosenfeld
The Feasibility Study And Characterziation Of A Two-Dimensional Diode Array In “Magic Phantom” For High Dose Rate Brachytherapy Quality Assurance, A Espinoza, B Beeksma, M Petasecca, I Fuduli, C Porumb, D L. Cutajar, S Corde, M A. Jackson, M Lf Lerch, Anatoly B. Rosenfeld
Faculty of Engineering and Information Sciences - Papers: Part A
High dose rate (HDR) brachytherapy is a radiation treatment technique capable of delivering large dose rates to the tumor. Radiation is delivered using remote afterloaders to drive highly active sources (commonly 192Ir with an air KERMA strength range between 20 000 and 40 000 U, where 1 U = 1 uGy m2/h in air) through applicators directly into the patient's prescribed region of treatment. Due to the obvious ramifications of incorrect treatment while using such an active source, it is essential that there are methods for quality assurance (QA) that can directly and accurately verify the treatment plan and the …
Nitrogen Removal From Natural Gas Using Solid Boron: A First-Principles Computational Study, Qiao Sun, Meng Wang, Zhen Li, Ping Li, Weihua Wang, Xiaojun Tan, Aijun Du
Nitrogen Removal From Natural Gas Using Solid Boron: A First-Principles Computational Study, Qiao Sun, Meng Wang, Zhen Li, Ping Li, Weihua Wang, Xiaojun Tan, Aijun Du
Australian Institute for Innovative Materials - Papers
Selective separation of nitrogen (N2) from methane (CH4) is highly significant in natural gas purification, and it is very challenging to achieve this because of their nearly identical size (the molecular diameters of N2 and CH4 are 3.64 Å and 3.80 Å, respectively). Here we theoretically study the adsorption of N2 and CH4 on B12 cluster and solid boron surfaces a-B12 and c-B28. Our results show that these electron-deficiency boron materials have higher selectivity in adsorbing and capturing N2 than CH4, which provides very useful information for experimentally exploiting boron materials for natural gas purification.
Aging Effect Evolution During Ferroelectric-Ferroelectric Phase Transition: A Mechanism Study, Zuyong Feng, Zhenxiang Cheng, Dongqi Shi, S X. Dou
Aging Effect Evolution During Ferroelectric-Ferroelectric Phase Transition: A Mechanism Study, Zuyong Feng, Zhenxiang Cheng, Dongqi Shi, S X. Dou
Australian Institute for Innovative Materials - Papers
Aging can significantly modify the dielectric, piezoelectric, and ferroelectric performance of ferroelectrics. However, little attention has been paid to the aging effect during ferroelectric-ferroelectric phase transitions that is essentially correlated with real applications. In this letter, the authors report the aging effect evolution between two ferroelectric phases in an acceptor-doped piezoceramics. The results show that aging-induced double hysteresis loops were exhibited in different ferroelectric phases, but disappeared during ferroelectric-ferroelectric phase transitions, suggesting the mechanism that the intrinsic restoring force for the reversible switching of domains caused by the alignment of defect dipoles was weakened due to ferroelectric dipole reorientation.
A Study Of Tio2 Binder-Free Paste Prepared For Low Temperature Dye-Sensitized Solar Cells, Jeremy H. Yune, Inna Karatchevtseva, Gerri Triani, Klaudia Wagner, David Officer
A Study Of Tio2 Binder-Free Paste Prepared For Low Temperature Dye-Sensitized Solar Cells, Jeremy H. Yune, Inna Karatchevtseva, Gerri Triani, Klaudia Wagner, David Officer
Australian Institute for Innovative Materials - Papers
A binder-free titania paste was prepared by chemical modification of an acidic TiO2 sol with ammonia. By varying the ammonia concentration, the viscosity of the acidic TiO2 suspension increased, thereby allowing uniform films to be cast. The photoelectrochemical performance of TiO2 electrodes, cast as single layers, was dependent on the thermal treatment cycle. Fourier transform infrared spectroscopy was used to characterize the extent of residual organics and found that acetates from the TiO2 precursor preparation were retained within the electrode structure after thermal treatment at 150 °C. Electrodes of nominal thickness 4 lm produced an energy conversion efficiency as high …
Comparative Displacement Study Of Bilayer Actuators Comprising Of Conducting Polymers, Fabricated From Polypyrrole, Poly(3,4- Ethylenedioxythiophene) Or Poly(3,4-Propylenedioxythiophene), Babita Gaihre, Syed Ashraf, Geoffrey M. Spinks, Peter C. Innis, Gordon G. Wallace
Comparative Displacement Study Of Bilayer Actuators Comprising Of Conducting Polymers, Fabricated From Polypyrrole, Poly(3,4- Ethylenedioxythiophene) Or Poly(3,4-Propylenedioxythiophene), Babita Gaihre, Syed Ashraf, Geoffrey M. Spinks, Peter C. Innis, Gordon G. Wallace
Australian Institute for Innovative Materials - Papers
The stress gradient generated due to electrochemical oxidation/reduction of a conducting polymer in a bilayer actuator causes a bending movement. Here we report a comparative study of the displacement of bilayer actuators prepared using different conducting polymers. The effects of conducting polymers obtained from electrochemical or chemical synthesis route: different polymers (polypyrrole (PPy), poly(3,4-ethylenedioxythiophene) PEDOT and poly(3,3-dihexyl-3-4-dihydro-2H-thieno[3,4b][1,4]-dioxepine [PProDOT(Hx) 2]); and different electrolytes (0.1 M lithium trifluromethanesulfonate/propylenecarbonate (LiTFSI/PC) and 1-ethyl-3-methyl imidazolium trifluromethanesulfonate (EMITFSI)) on the displacement amplitude and displacement patterns of these actuators were investigated and compared. The results indicate that the bilayer actuator consisting of an electrochemically synthesized conducting polymer …
Study On The Influence Of Temperature On The Surface Asperity In Micro Cross Wedge Rolling, H N. Lu, D B. Wei, Z Y. Jiang, D Wu, X M. Zhao
Study On The Influence Of Temperature On The Surface Asperity In Micro Cross Wedge Rolling, H N. Lu, D B. Wei, Z Y. Jiang, D Wu, X M. Zhao
Faculty of Engineering and Information Sciences - Papers: Part A
When the common deformation processes are scaled down to micro/meso dimensions, size effect is the particular phenomena in microforming, which is related to the dominant influence of single grains inside the micropart. The conventional cross wedge rolling (CWR) is introduced into the micro scale in order to take the advantages of CWR. The micro cross wedge rolling (MCWR) has to confront with the phenomena of size effect that occurs in the common microforming processes inevitably. One of the approaches to compensate size effect is to increase the deforming temperature. An increased formability is achieved because more slip systems of polycrystal …
The Study Of Flood Hydraulics Before The Building Of Maroon Dam By Hec-Ras, Maskingam And Muskingum - Cunge Method, Mohammad Hossein Naghshine, Farhad Fakheri Raof, Ali Khoshrftar
The Study Of Flood Hydraulics Before The Building Of Maroon Dam By Hec-Ras, Maskingam And Muskingum - Cunge Method, Mohammad Hossein Naghshine, Farhad Fakheri Raof, Ali Khoshrftar
Faculty of Engineering and Information Sciences - Papers: Part A
Routing of rivers which flow through the important areas is from the important river engineering measures. In this research, flood routing in the Maroon River has been studied bases on hydrometric stations between Behbahan and Chamnezam. Todays, numerical computer methods are developed for the Cent and Nante equations. The HEC-RAS software and Muskingum and Muskingum - corners methods are used for this work. HEC-RAS model with solving of dynamic equations motion simulates unsteady flow in the form of onedimensional flow in open channels. After calibration and testing, the results of these methods were compared.So, the HEC-RAS model results considerably better …
Study Of Shear-Stiffened Elastomers, Tongfei Tian, Weihua Li, Jie Ding, Gursel Alici, Haiping Du
Study Of Shear-Stiffened Elastomers, Tongfei Tian, Weihua Li, Jie Ding, Gursel Alici, Haiping Du
Faculty of Engineering and Information Sciences - Papers: Part A
Shear thickening fluids, which are usually concentrated colloidal suspensions composed of non-aggregating solid particles suspended in fluids, exhibit a marked increase in viscosity beyond a critical shear rate. This increased viscosity is seen as being both 'field-activated', due to the dependence on shearing rate, as well as reversible. Shear thickening fluids have found good applications as protection materials, such as in liquid body armor, vibration absorber or dampers. This research aims to expand the protection material family by developing a novel solid status shear thickening material, called shear-stiffened elastomers. These new shear-stiffened elastomers were fabricated with the mixture of silicone …
Parameter Identification Study Of Frequency Response Data For A Trilayer Conjugated Polymer Actuator Displacement Model, Emmanuel D. Blanchard, Mitchell J. Smith, Chuc H. Nguyen
Parameter Identification Study Of Frequency Response Data For A Trilayer Conjugated Polymer Actuator Displacement Model, Emmanuel D. Blanchard, Mitchell J. Smith, Chuc H. Nguyen
Faculty of Engineering and Information Sciences - Papers: Part A
This article investigates the effect of three uncertain parameters on a model of conjugated polymer actuators. These uncertain parameters are the diffusion coefficient (D), the resistance (R), and the double-layer WKLFNQHVV / 7KH PRGHO VHQVLWLvity to these parameters is analyzed and a parameter estimation study is performed using artificially generated data as well as laboratory yielded experimental measurements. The parameter estimation method used in this article is based on a Bayesian cost function, and gives us an insight on how much the estimation can be trusted, which is useful information for the design of controllers. Results indicate that for stochastic …
An Application Of Nonlinear Feature Extraction – A Case Study For Low Speed Slewing Bearing Condition Monitoring And Prognosis, Wahyu Caesarendra, Prabuono Buyung Kosasih, A K. Tieu, Craig Moodie
An Application Of Nonlinear Feature Extraction – A Case Study For Low Speed Slewing Bearing Condition Monitoring And Prognosis, Wahyu Caesarendra, Prabuono Buyung Kosasih, A K. Tieu, Craig Moodie
Faculty of Engineering and Information Sciences - Papers: Part A
This paper presents the application of four nonlinear methods of feature extraction in slewing bearing condition monitoring and prognosis: these are largest Lyapunov exponent, fractal dimension, correlation dimension, and approximate entropy methods. Although correlation dimension and approximate entropy methods have been used previously, the largest Lyapunov exponent and fractal dimension methods have not been used in vibration condition monitoring to date. The vibration data of the laboratory slewing bearing test-rig run at 1 rpm was acquired daily from February to August 2007 (138 days). As time progressed, a more accurate observation of the alteration of bearing condition from normal to …
An Investigation On The Impacts Of Density Currents On The Sedimentation In Dam Reservoirs Using Tcm Model; Case Study: Maroon Dam, Farhad Fakheri Raof, Mohammad Hossein Naghshine, Ali Khoshrftar
An Investigation On The Impacts Of Density Currents On The Sedimentation In Dam Reservoirs Using Tcm Model; Case Study: Maroon Dam, Farhad Fakheri Raof, Mohammad Hossein Naghshine, Ali Khoshrftar
Faculty of Engineering and Information Sciences - Papers: Part A
Sedimentation in dams' reservoirs is one of the most pressing concerns facing dams today. Maroon reservoir dam, located in Khuzestan Province, is one of the most important dams in this region. Since it is a new constructed dam, numerical simulation of sedimentation trend in its reservoirs could significantly help on a better utilization. To this end, TCM model which is capable to simulate density currents was used. The obtained results show that the dam loses about 91 million m3 of its reservoirs during a 50-year exploitation period.
Detecting Vmat Delivery Errors: A Study On The Sensitivity Of The Arccheck-3d Electronic Dosimeter, S Arumugam, A Xing, G Goozee, L Holloway
Detecting Vmat Delivery Errors: A Study On The Sensitivity Of The Arccheck-3d Electronic Dosimeter, S Arumugam, A Xing, G Goozee, L Holloway
Faculty of Engineering and Information Sciences - Papers: Part A
The sensitivity of the ArcCHECK 3D dosimeter in detecting VMAT delivery errors has been investigated. Dose and leaf positional errors of different magnitudes were introduced to whole arc and individual control points (CPs) of a simple open arc VMAT plan. The error introduced and error free plans were delivered and measured using the ArcCHECK device. The measured doses were compared against the treatment planning system calculated doses using gamma criteria with 2 percent 2mm and 3 percent 3mm tolerance levels. ArcCHECK effectively detected the dose errors resulting from MLC leaf positioning errors in limited CPs and Whole arc. For errors …
Image Guidance During Breast Radiotherapy: A Phantom Dosimetry And Radiation-Induced Second Cancer Risk Study, A Quinn, L Holloway, Peter Metcalfe
Image Guidance During Breast Radiotherapy: A Phantom Dosimetry And Radiation-Induced Second Cancer Risk Study, A Quinn, L Holloway, Peter Metcalfe
Faculty of Engineering and Information Sciences - Papers: Part A
Imaging procedures utilised for patient position verification during breast radiotherapy can add a considerable dose to organs surrounding the target volume on top of therapeutic scatter dose. This study investigated the dose from a breast kilovoltage cone-beam CT (kV-CBCT), a breast megavoltage fan-beam CT (MV-FBCT), and a TomoDirectTM breast treatment. Thermoluminescent dosimeters placed within a female anthropomorphic phantom were utilised to measure the dose to various organs and tissues. The contralateral breast, lungs and heart received 0.40 cGy, 0.45 cGy and 0.40 cGy from the kV-CBCT and 1.74 cGy, 1.39 cGy and 1.73 cGy from the MV-FBCT. In comparison to …
Similarity-Based Search For Model Checking: A Pilot Study With Java Pathfinder, Elmin Ibrahimov, Jixing Wang, Zhiquan Zhou
Similarity-Based Search For Model Checking: A Pilot Study With Java Pathfinder, Elmin Ibrahimov, Jixing Wang, Zhiquan Zhou
Faculty of Engineering and Information Sciences - Papers: Part A
When a model checker cannot explore the entire state space because of limited resources, model checking becomes a kind of testing with an attempt to find a failure (violation of properties) quickly. We consider two state sequences in model checking: (i) the sequence in which new states are generated, and (ii) the sequence in which the states generated in sequence (i) are checked for property violation. We observe that neighboring states in sequence (i) often have similarities in certain ways. Based on this observation we propose a search strategy, which generates sequence (ii) in such a way that similar states …
Parameter Identification Study Of A Trilayer Conjugated Polymer Actuator Curvature Model, Emmanuel D. Blanchard, Patrick S. Chen, Chuc H. Nguyen
Parameter Identification Study Of A Trilayer Conjugated Polymer Actuator Curvature Model, Emmanuel D. Blanchard, Patrick S. Chen, Chuc H. Nguyen
Faculty of Engineering and Information Sciences - Papers: Part A
This article investigates the effect of two uncertain parameters on a recent new model of conjugated polymer actuators. These uncertain parameters are the diffusion coefficient (D) and the double-layer capacitance (C dl), which are difficult to measure directly. The model sensitivity to these parameters is analysed and a parameter estimation study is performed using artificially generated data. The parameter estimation method used in this article is based on a Bayesian cost function, and gives us an insight on how much the estimation can be trusted, which is useful information for the design of controllers. Results indicate that for controllers to …
An Exploratory Study On The Adoption And Use Of Ict In Myanmar, Sim Kim Lau, Graham Kenneth Winley, S. Lau, Kim Song Tan
An Exploratory Study On The Adoption And Use Of Ict In Myanmar, Sim Kim Lau, Graham Kenneth Winley, S. Lau, Kim Song Tan
Faculty of Engineering and Information Sciences - Papers: Part A
This exploratory study investigates the adoption and use of information and communication technologies in Myanmar by examining the nature and structure of the information technology profession. The investigation is based on a theoretical framework consisting of three components: domains of information technology professional expertise; the scope of the information technology professional's knowledge, skills and experience; and specific knowledge and skills associated with the domains of professional expertise. The findings show that specialist skills in systems development, database, network and communications are important. This paper also provides insights that are not found in current literature which investigates information technology skills in …
Experimental Study And Modeling Of A Novel Magnetorheological Elastomer Isolator, Jian Yang, Haiping Du, Weihua Li, Yancheng Li, Jianchun Li, Shuaishuai Sun, H X. Deng
Experimental Study And Modeling Of A Novel Magnetorheological Elastomer Isolator, Jian Yang, Haiping Du, Weihua Li, Yancheng Li, Jianchun Li, Shuaishuai Sun, H X. Deng
Faculty of Engineering and Information Sciences - Papers: Part A
This paper reports an experimental setup aiming at evaluating the performance of a newly designed magnetorheological elastomer (MRE) seismic isolator. As a further effort to explore the field-dependent stiffness/damping properties of the MRE isolator, a series of experimental testing were conducted. Based upon the analysis of the experimental responses and the characteristics of the MRE isolator, a new model that is capable of reproducing the unique MRE isolator dynamics behaviors is proposed. The validation results verify the model's effectiveness to portray the MRE isolator. A study on the field-dependent parameters is then provided to make the model valid with fluctuating …
Integrating Building Information Modelling (Bim) Into Engineering Education: An Exploratory Study Of Industry Perceptions Using Social Network Data, Kriengsak Panuwatwanich, Mei Liang Wong, Jeung-Hwan Doh, Rodney A. Stewart, Timothy J. Mccarthy
Integrating Building Information Modelling (Bim) Into Engineering Education: An Exploratory Study Of Industry Perceptions Using Social Network Data, Kriengsak Panuwatwanich, Mei Liang Wong, Jeung-Hwan Doh, Rodney A. Stewart, Timothy J. Mccarthy
Faculty of Engineering and Information Sciences - Papers: Part A
Building Information Modelling (BIM) has been widely acknowledged as an emerging technological and procedural shift within the Architecture, Engineering and Construction (AEC) industry. BIM represents a methodology to manage the building design and project data in digital format throughout a building lifecycle. With the implementation of BIM, the design, construction and operation processes can be better streamlined to improve project efficiency. Because of its far-reaching benefits, there is a current push for BIM by governments worldwide, including Australia. However, a significant lack of the understanding of BIM and industry readiness has been identified as a major hindrance; hence, there is …
An Exploratory Study Of Personal Reflection And Collaboration Skills Using Online Collaborative Tool In Project-Based Learning, Sim Kim Lau, Wendy Meyers
An Exploratory Study Of Personal Reflection And Collaboration Skills Using Online Collaborative Tool In Project-Based Learning, Sim Kim Lau, Wendy Meyers
Faculty of Engineering and Information Sciences - Papers: Part A
By deepening our understanding of the use of Web 2.0 for reflective practice, knowledge co-construction and project based learning this paper aims to contribute to our understanding of collaborative learning. The paper investigates a case study of a post-graduate system development subject to increase student learning through the development of students' personal reflection and collaboration skills. The project aims to develop key foundational knowledge and skills identified in the IS 2010 curriculum guidelines, i.e. the ability to work collaboratively. Of particular interest was the ability of student collaboration combined with personal reflective learning to lead to negotiation of meaning and …
Study Of Pdms Based Magnetorheological Elastomers, Tongfei Tian, Xing Zhong Zhang, Weihua Li, Gursel Alici, J Ding
Study Of Pdms Based Magnetorheological Elastomers, Tongfei Tian, Xing Zhong Zhang, Weihua Li, Gursel Alici, J Ding
Faculty of Engineering and Information Sciences - Papers: Part A
The fabrication of conventional magnetorheological elastomers (MRE) is usually taken more than 1 day because the conventional matrixes such as natural rubber and silicone rubber need long curing time to become solid state. This study presents a rapid method for fabricating MRE within 90 minutes by using poly(dimethylsiloxane) (PDMS) as the matrix thanks to the rapid curing of PDMS in high temperature. A total of four PDMS based MRE samples were fabricated. Their mechanical and rheological properties under both steady-state and dynamic loading conditions were tested with a parallel-plate rheometer. Additionally, the microstructures of the PDMS based MREs were also …