Engineering Commons^™

A Growth Mixture Theory For Cartilage, Stephen M. Klisch, Robert L. Sah, Anne Hoger

Mechanical Engineering

In this paper we present a model of growth for cartilaginous tissues in which there exists a saturated solid matrix composed of multiple constituents that may grow and remodel independently of each other. Klisch and Hoger recently developed a general theory of volumetric growth for a mixture of ν-1 growing elastic materials and an inviscid fluid, which included a treatment of two special types of internal constraints that are relevant to cartilage. Here, that theory is specialized to construct a cartilage growth model. This theory allows the constituents of the solid matrix to grow independently of each other, and can …

A Comparison Of Two Actuators For A Semi-Active Helmholtz Resonator, Charles Birdsong, Clark J. Radcliffe

Mechanical Engineering

Two electro-mechanical actuators are examined for a semi-active Helmholtz resonator acoustic device. The device is used to reflect narrow band noise back to the source in an acoustic duct. The controller and actuator are used to tune the system on-line allowing optimum performance over a range of operating conditions. Actuator. dynamics play an important role in the controller design and the operation of the device. Two variations of an electro-mechanical actuator are considered here. The first uses a dual voice coil speaker with local feedback compensation and the second uses the same speaker without the compensation. It is shown that …

Development And Validation Of A Pedestrian Lower Limb Non-Linear 3-D Finite Element Model, Peter Schuster, Gopal Jayaraman

Mechanical Engineering

Lower limb injury is becoming an increasingly important concern in vehicle safety for both occupants and pedestrians. To enable vehicle manufacturers to better understand the biomechanical effects of design changes, it is deemed beneficial to employ a biomechanically fidelic finite element model of the human lower limb.

The model developed in this study includes long bones (tibia, fibula, femur) and flat bone (patella) as deformable bodies. The pelvis and foot bones are modeled as rigid bodies connected to the femur and tibia/fibula via rotational spring-dashpots. The knee is defined by scanned bone surface geometry and is surrounded by the menisci, …

Preliminary Design Of An Electrodynamic Balance For Single Particle Analysis, C. Bobcowski, J. Costa, S. Shaw, R. Zucal, J. Schmalzel, R. Ordonez, John Chen

Mechanical Engineering

An electrodynamic chamber (EDC) is a device that controls the electrodynamic field surrounding a single particle. By suspending the particle at a fixed point in space, various measurements can be made to determine thermodynamic properties of the particle. This paper describes the preliminary engineering development of an EDC for combustion research at Rowan University.

A Special Theory Of Biphasic Mixtures And Experimental Results For Human Annulus Fibrosus Tested In Confined Compression, Stephen M. Klisch, Jeffrey C. Lotz

Mechanical Engineering

A finite deformation mixture theory is used to quantify the mechanical properties of the annulus fibrosus using experimental data obtained from a confined compression protocol. Certain constitutive assumptions are introduced to derive a special mixture of an elastic solid and an inviscid fluid, and the constraint of intrinsic incompressibility is introduced in a manner that is consistent with results obtained for the special theory. Thirty-two annulus fibrosus specimens oriented in axial (n = 16) and radial (n = 16) directions were obtained from the middle-lateral portion of intact intervertebral discs from human lumbar spines and tested in a stress-relaxation protocol. …

Technology In Engineering Education: What Do The Faculty Know (And Want) Anyway?, John C. Chen, Michael Ellis, Jason Lockhart, Sameer Hamoush, Catherine E. Brawner

Mechanical Engineering

We have conducted a survey of engineering faculty at the eight SUCCEED coalition universities to identify the training needs and present levels of experience with various technologies. The results of that survey are presented in this paper.

The most surprising finding from the survey is that, despite the wide differences in the Coalition’s colleges of engineering (in size, student demographics, and research-teaching emphasis, for example), the survey results are similar for all campuses. This is important in that it implies that the survey results may be widely applicable to other universities, even given the disparate state of technology integration and …