Engineering Commons^™

Remediating Soil For Successful Vegetation Establishment Along Nebraska Highways, Shad Mills, Martha Mamo, Walt Schacht, Humberto Blanco-Canqui

Nebraska Department of Transportation: Research Reports

Vegetation along roadsides is important to prevent soil erosion, provide habitat, and filter water running off the road. Vegetation close to the pavement along highways in Nebraska does not readily establish and persist. It is thought that the sodium and bulk density are the driving factors behind the lack of vegetation. After a construction project the shoulder is seeded into the compacted soil, and during winter salts can accumulate in the soil because of deicing agents being used. The purpose of our study was to determine if the sodium and bulk density are the driving factors of the vegetation cover. …

Establishment Of Wildflower Islands To Enhance Roadside Health And Aesthetics, Walter Schacht, Judy Wu-Smart

Nebraska Department of Transportation: Research Reports

Wildflowers are crucial in the ecological function of the low-input roadside plant communities in terms of water andnutrient cycling, nutrient inputs such as nitrogen, total plant canopy cover, stand longevity, and provision of habitat for numerous small animals. Further, wildflowers provide critical foraging and nesting resources for birds, insects, and other wildlife. Unfortunately, habitat loss from agricultural and urban development has led to rapid population declines in wild bees and other pollinators across the US, thereby jeopardizing not only food production but also the sustainability of our natural landscapes (Kearns & Inouye, 1997). One way to mitigate wild bee decline …

Development Of High-Performance Rapid Patching Materials For Pavement Repair, Gholami Shayan, Jiong Hu, Yong-Rak Kim

Nebraska Department of Transportation: Research Reports

Concrete pavements exhibiting severe distresses which require patching are commonly observed in the concrete pavement in Nebraska. Due to the requirements of opening pavement to traffic after placing the rapid patching materials, it is essential for that concrete to achieve high early strength. To ensure this, a high cement content and chloride-based accelerators are currently used in the Nebraska Department of Transportation (NDOT) Portland cement-based rapid-patching materials. Besides its associated high cost, high cement content tends to result in a less stable mix with high shrinkage, high heat of hydration, and high cracking potential. In addition, using chloride-based accelerators has …

Standard Design For Nebraska County Bridges, Chungwook Sim, Jiong Hu, Maher K. Tadros, Alexander Bleyhl, David Gee

Nebraska Department of Transportation: Research Reports

Many county-owned bridges in Nebraska need replacement due to their structural deficiency. Most of the bridges needing replacement are in the 40 to 60 ft range. This span range lacks a standard design that fits Nebraska county practices in terms of speed and simplicity of construction. The current systems being used are (a) Precast 1 by 2 ft planks which can span up to 30 ft, (b) Cast-in-place slab bridges which can span up to 50 ft but require extensive field formwork, concrete placing, and curing, and are best when constructed in three-span units, and (c) Inverted tees which can …

Evaluation Of Reducing Cement Content In Ndor Class R Combined Aggregate Gradations, Miras Mamirov, Jiong Hu, Yong-Rak Kim

Nebraska Department of Transportation: Research Reports

The main objective of this research project was to achieve a cement reduction on Nebraska slip-form pavement concrete through aggregate particle packing optimization. A literature review was conducted to examine different aggregate optimization tools, quality control tests, and historical data of Nebraska Department of Transportation (NDOT) pavement mixtures. It was found that the Modified Toufar Model has good potential in optimizing particle packing and predicting packing degrees. The combined aggregate void content test was found to be useful to experimentally justify optimized aggregate gradations. The Box Test with a modified index and image analysis tool for surface void estimation was …

Long-Term Performance Evaluation Of Nudeck In Kearney East Bypass, George Morcous, Marc Maguire

Nebraska Department of Transportation: Research Reports

The Kearney East Bypass bridge is the first project that implements the newly developed precast concrete deck system (known as 2nd generation NUDECK). The new system consists of full-depth full-width precast prestressed concrete deck panels that are 12 ft (3.66 m) long each. The panels have covered shear pockets at 4 ft (1.22 m) spacing on each girder line to host clustered shear connectors that are adjustable in height. Narrow unreinforced transverse joints are used to eliminate the need for deck overlay. Also, deck panels are post-tensioned in the longitudinal direction using a new post-tensioning system that eliminates the need …

Condition Assessment Of Bridge Decks With Asphalt Overlay, Sepehr Pashoutani, Jinying Zhu

Nebraska Department of Transportation: Research Reports

Ground penetrating RADAR (GPR) is a widely used nondestructive testing (NDT) method for bridge deck evaluation. However, the current GPR signal and data processing software and algorithms are not able to provide comprehensive information about bridge deck condition. Although the original objective of this research project was to develop GPR analysis algorithms for condition assessment of bridge decks with asphalt overlay, the scope of work has been expanded to concrete bridge decks with or without overlays.

In this study, the research team developed a complete GPR analysis procedure that includes the following components: 1) obtain zero-time for GPR reflection at …

Precast Concrete Deck-To-Girder Connection Using Uhpc, George Morcous, Mostafa Abo El-Khier

Nebraska Department of Transportation: Research Reports

The implementation of ultra-high-performance concrete (UHPC) in bridge construction has been growing rapidly in the last two decades due to its excellent mechanical properties, workability, and durability. This report presents a new UHPC connection between precast concrete deck panels and bridge girders that eliminates changes to the design and production of girder shear connectors commonly used in conventional cast-in-place concrete deck construction. In conventional construction, girder shear reinforcement or studs are extended into the cast-in-place concrete deck to transfer interface shear and create composite section. In the new connection, girder shear reinforcement or studs are kept underneath the deck panels, …

The Application Of Gray-Scale Level-Set Method In Segmentation Of Concrete Deck Delamination Using Infrared Images, Chongsheng Cheng, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Conventional nondestructive delamination detection of concrete pavements through thermography is often based on temperature contrasts between delaminated and sound areas. Non-uniform backgrounds caused by the environmental conditions are often challenging for contrast-based methods to robustly differentiate the delaminated areas from the sound areas. Instead of focusing on the temperature contrast, this study proposes a temperature gradient-based level set method (LSM) to detect boundaries for delamination segmentations. A modified edge indicator function is developed to represent the normalized temperature gradient of a thermal image. The experimental study was conducted to evaluate its applicability and stability for boundary detection in terms of …

Investigation Of Dsr Test Methods To Determine Binder Low Temperature Properties, Kommidi Santosh, Yong-Rak Kim

Nebraska Department of Transportation: Research Reports

The low temperature rheology of bituminous binders is of great interest because low temperature cracking is one of the primary asphalt pavement failure modes observed in cold-climate places such as Nebraska. Low temperature binder characterization/grading has been primarily conducted using the bending beam rheometer (BBR), while the dynamic shear rheometer (DSR) can alternatively be used to characterize the low temperature properties of binders with the recent advancement of DSR equipment that can cover a wide range of testing temperatures. This study investigates alternative testing-analysis methods using the DSR to determine low temperature asphalt binder properties that have been measured by …

Performance Evaluation Of Inverted Tee (It) Bridge System, Garrett P. Martindale, Daniel Watson, Antony Mohsen Kamal Masoud Kodsy, Mostafa Abo El-Khier, Richard L. Wood, George Morcous

Nebraska Department of Transportation: Research Reports

The Inverted Tee (IT) girder bridge system was originally developed in 1996 by the University of Nebraska–Lincoln (UNL) researchers and Nebraska Department of Transportation (NDOT) engineers. This bridge system currently accounts for over 110 bridges in Nebraska used for both state highways and local county roads. Extensive longitudinal and transverse deck cracking have been observed and noted in numerous bridge inspection reports. Since the IT girder bridge system is relatively new, limited data and knowledge exist on its structural performance and behavior. This study evaluates the IT girder bridge system by conducting twenty field observations as well as recording accelerometer, …

Biomethane Production From Distillery Wastewater, Zachary Christman

Department of Agronomy and Horticulture: Dissertations, Theses, and Student Research

Distillery wastewater treatment is a great ecological problem, for example, India produces 2.7 billion liters of alcohol that results in 40 billion liters of wastewater. However, this material can be seen as a resource since 11 million cubic meters of biogas at 60% methane could be produced in addition to cleaning the water. The distillery has two options of what to do with the biogas. The first is to use the biogas to fuel the distillery making the production plant more energy efficient and removing some of the need to buy natural gas. The other is to upgrade the biogas …

Restricted Crossings On Rural Highways, John Sangster, Tim Adams

Nebraska Department of Transportation: Research Reports

This study examines the potential for replacing the standard intersection design at two-way stop control (TWSC) and all- way stop control (AWSC) intersections along rural highways with a roundabout or a restricted crossing u-turn (RCUT) facility. The geometry of the RCUT design prohibits left and through movements from the side road, and provides a u-turn location downstream from the main crossing. This type of facility has been implemented for rural highways extensively in both Maryland and North Carolina, as well as in limited cases in many other states such as Minnesota and Missouri, with the potential to serve as a …

Assessing The Impact Of Game Day Schedule And Opponents On Travel Patterns And Route Choice Using Big Data Analytics, Anuj Sharma, Vesal Ahsani

Nebraska Department of Transportation: Research Reports

The transportation system is crucial for transferring people and goods from point A to point B. However, its reliability can be decreased by unanticipated congestion resulting from planned special events. For example, sporting events collect large crowds of people at specific venues on game days and disrupt normal traffic patterns.

The goal of this study was to understand issues related to road traffic management during major sporting events by using widely available INRIX data to compare travel patterns and behaviors on game days against those on normal days. A comprehensive analysis was conducted on the impact of all Nebraska Cornhuskers …

Asphalt Binder Laboratory Short-Term Aging, Hamzeh Haghshenas, Robert C. Rea

Nebraska Department of Transportation: Research Reports

The Rolling Thin Film Oven (RTFO) is widely used to simulate asphalt binder short-term aging. However, there is a general interest to improve the current short-term aging protocol especially for reducing the aging time. Besides, there are some doubts about the capability of RTFO in the simulation of aging of highly polymer modified asphalt binders which is mainly due to improper dispersion of such binders in the bottles during rotating and creeping of highly viscous binder out of the bottles during rotation. This work addresses the effect of time, temperature, airflow rate, and weight of asphalt binder on the laboratory …

Restricted Crossing U-Turns At Rural Intersections, Timothy Adams

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

This study examines the potential for replacing the standard intersection design at two-way stop control (TWSC) and all-way stop control (AWSC) intersections along rural highways with a roundabout or a restricted crossing u-turn (RCUT) facility. The geometry of the RCUT design prohibits left and through movements from the side road, and provides a u-turn location downstream from the main crossing. This type of facility has been implemented for rural highways extensively in other states and has the potential to serve as a cost-effective solution to improve roadway safety within Nebraska.

Comparative analysis is conducted for three site locations (Humphrey, Madison, …

Unl-Cc Outdoor Education Center Master Plan, Marie Wagner

Honors Theses

The following report contains the work done by the group Griswold Engineering in completion of the Senior Design requirements for Civil Engineering and the Honors Requirements of the Project Manager. As the project manager, my job was to organize the project as a whole and to work alongside the Structural Engineer on the project. One of the main problems to overcome was the division of labor amongst the group. The project was originally conceived as a group project with one project manager and five other students to serve as the project engineers in each subdiscipline. Since this group only had …

Civil Engineering Design Of Cornhusker Council's Outdoor Education Center, Kelly Weiler

Honors Theses

A team of geotechnical, structural, hydraulic, environmental, and transportation experts collaborated to provide engineering solutions to the Cornhusker Council in an effort to solve the current problems facing their Outdoor Education Center. This results of this project provided the structural design of three bridges on the property, transportation plans for two parking lots and roadway design, geotechnical recommendations for soil testing and erosion prevention, and an environmental and hydraulic analysis of the property. A major challenge in the design of this project is the consideration of the dangers and regulations that accompany the floodway and floodplain regions on site. Various …

34-Inch Tall Three Beam Transition To Concrete Buttress, Scott Rosenbaugh, Wyatt Fallet, Ronald K. Faller, Robert W. Bielenberg, Jennifer Schmidt

Nebraska Department of Transportation: Research Reports

Roadway resurfacing and overlay projects effectively reduce the height of roadside barriers placed adjacent to the roadway, which can negatively affect their crashworthiness. More recently, bridge rails and concrete barriers have been installed with slightly increased heights to account for future overlays. However, adjacent guardrails and approach transitions have not yet been modified to account for overlays. The objective of this project was to develop an increased-height, approach guardrail transition (AGT) to be crashworthy both before and after roadway overlays of up to 3 in. (76 mm).

A 34-in. (864-mm) tall, thrie beam transition was designed such that the system …

Bridge Deck Delamination Segmentation Based On Aerial Thermography Through Regularized Grayscale Morphological Reconstruction And Gradient Statistics, Chongsheng Cheng, Zhexiong Shang, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Environmental and surface texture-induced temperature variation across the bridge deck is a major source of errors in delamination detection through thermography. This type of external noise poises a significant challenge for conventional quantitative methods such as global thresholding and k-means clustering. An iterative top-down approach is proposed for delamination segmentation based on grayscale morphological reconstruction. A weight-decay function was used to regularize the reconstruction for regional maxima extraction. The mean and coefficient of variation of temperature gradient estimated from delamination boundaries were used for discrimination. The proposed approach was tested on a lab experiment and an in-service bridge deck. The …

Thermographic Laplacian-Pyramid Filtering To Enhance Delamination Detection In Concrete Structure, Chongsheng Cheng, Ri Na, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Despite decades of efforts using thermography to detect delamination in concrete decks, challenges still exist in removing environmental noise from thermal images. The performance of conventional temperature-contrast approaches can be significantly limited by environment-induced non-uniform temperature distribution across imaging spaces. Time-series based methodologies were found robust to spatial temperature non-uniformity but requires extended period to collect data. A new empirical image filtering method is introduced in this paper to enhance the delamination detection using blob detection method that originated from computer vison. The proposed method employs a Laplacian of Gaussian filter to achieve multi-scale detection of abnormal thermal patterns by …

Optimizing In-Place Density Of Asphalt Pavements During Cold Weather Paving In Nebraska, Robert C. Rea, Hamzeh Haghshenas

Nebraska Department of Transportation: Research Reports

Late season paving is common and often performed in colder temperatures, which is the most challenging environment for attaining optimal in-place density/compaction The in-place density of asphalt pavement greatly affects the lifespan of the pavement. It is also a key factor in preventing major pavement distresses, such as rutting, cracking, stripping (due to water damage) and aging. This research project aims to evaluate and compare the effectiveness of different compaction, delivery, and mix design characteristics to ensure the optimization of in-place asphalt pavement density. To this end, various laydown methods (i.e., Standard Pick-up Machine (SPM) and Material Transfer Vehicle (MTV)) …

Validation Of The Highway Capacity Manual Urban Street Travel Time Reliability Methodology Using Empirical Data, Ernest Tufuor, Laurence Rilett

Mid-America Transportation Center: Final Reports and Technical Briefs

The 6th edition of the Highway Capacity Manual (HCM-6) includes the concept of travel time reliability (TTR), which attempts to determine the distribution of average trip travel times over an extended period. TTR is an inherent part of travelers’ route choice decisions and is used by traffic managers to better quantify operations rather than simply using average travel times. The focus of this paper is on the HCM-6 urban street TTR methodology contained in Chapter 17. The approach uses historical data (e.g., weather and volume fluctuations) and simple empirical data (e.g., 1-day volume count) to provide the user with average …

Evaluation Of Nebraska’S Aggregate Reactivity By The Miniature Concrete Prism Test Method – Aashto T380, Lieska Halsey, Wally Heyen

Nebraska Department of Transportation: Research Reports

The evaluation of nine different aggregates shows the viability of the T380 test method as an alternative to the standard C1293 test method. The T380 assesses the Alkali-Silica Reaction potential of aggregates with the same reliability as C1293 and correlates well with the C1293 test method. Results are obtained within 56 days by T380 compared to 365 days required by C1293. The T380 method at 56 days appears to characterize the aggregate reactivity similarly to C1293 for all the aggregates evaluated in this study. Therefore, T380 will be part of the Department test method for approval of interground/blended cements along …

Research On High-Rap Asphalt Mixtures With Rejuvenators - Phase Ii, Hamzeh Haghshenas, Gabriel Nsengiyumva, Yong-Rak Kim, Kommidi Santosh, Soroosh Amelian

Nebraska Department of Transportation: Research Reports

A previous study by the authors have demonstrated effectiveness of three rejuvenators: R1 (triglyceride/fatty acid: agriculture-tech based), R2 (aromatic extract: petroleum-tech based), and R3 (tall oil: green-tech based) on rejuvenating properties of the aged binder. In that study, it was observed that the rejuvenators made high-RAP mixtures softer and more compliant, which may increase the rutting potential, while they simultaneously improve cracking resistance of the high-RAP materials. Research outcomes and findings from the previous study resulted in consequential research needs for more specific investigation of high-RAP mixtures with rejuvenators in order to achieve realistic implementation into future high-RAP paving projects …

Effect Of Moisture Condition On Concrete Core Strengths, Wally Heyen, Lieska Halsey

Nebraska Department of Transportation: Research Reports

The main purpose of this study was to determine if there would be any major differences between curing methods of cores taken for acceptance testing from a highway slab on a project. The comparison provided data to determine the effect of the moisture gradients created by these different curing treatments on core strength and core permeability. The strengths were measured of moist cured cores and sealed plastic bag cured cores from the day cores were obtained (14, 21 and 26 days) until they reached 28 days. Permeability was also measured at 26, 28 and 32 days. According to ASTM C42, …

Validation Of The Mechanical Rocker Test Method For Ice Melting Capacity (Mrt-Imc), Lieska Halsey, David Hansen

Nebraska Department of Transportation: Research Reports

The anti-icing and deicing industry has interest in the development of an objective, repeatable test procedure for the evaluation and comparison of anti-icing and deicing products. Pursuant to this goal, the Nebraska Department of Transportation (NDOT) funded research at the University of Nebraska-Lincoln (UNL) to investigate methods for evaluating deicing products, beginning in 2011[1]. Researchers at UNL developed the procedure for the Mechanical Rocker Test for Ice Melting Capacity (MRT or MRT-IMC) in 2014[2].

From 2017-2019, NDOT evaluated the MRT-IMC procedure for validity and suitability as a standard test procedure for assessing deicer performance. NDOT also explored opportunities to improve …

Investigating The Interaction Of Ndot Hot-Pour Pcc Joint Sealant And Penetrating Concrete Sealers, Bruce Barrett, Dale Byre, Wally Heyen, Lieska Halsey, David Hansen

Nebraska Department of Transportation: Research Reports

Based on the field observations on NE-83, PCS potentially impacts the bond between the concrete and hot-pour sealant after application. If penetrating sealers break the interfacial bond after application, concrete pavements could become compromised and subject to freeze-thaw damage, chloride attack, and other deleterious effects.

The results show that discoloration occurred when applying the five PCS products to the NE-3405 hot-pour sealed testing blocks. All three test methods of application; spraying, 1-min, and 5-min soaks, caused discoloration. The level of discoloration increased with the duration of contact with the PCS. Despite discoloration, none of the five PCS products caused de-bonding …

Assessing Impact And Blast Resilience Of Polymer Coated Cementitious Materials, Murtaza Nalwala, Gabriel Nsengiyumva, Yong-Rak Kim

UCARE Research Products

RESEARCH MOTIVATION The bridge piers are highly vulnerable to the impact and blast loads. The position in which they are constructed makes it difficult to install protective devices around them. By the current AASHTO standard, it is possible to under-design bridge piers for commercial vehicle impacts and other events such as blast.

OBJECTIVE To improve impact and blast resilience of bridge piers using polymeric coatings.

CONCLUSION Polymer coating of Portland cement concrete can be achieved with a good bonding. ü The polymeric coating seem to improve impact resilience of Portland cement concrete by increasing absorbed impact energy (i.e., area underneath …