Open Access. Powered by Scholars. Published by Universities.®
- Keyword
-
- CubeSat (3)
- ArkSat (1)
- Attitude control (1)
- Biocide dosing system (1)
- Burn Wire (1)
-
- Electrostatic Thruster (1)
- Fail-safe (1)
- Heat Transfer (1)
- High-density propellant (1)
- International Space Station (1)
- Joule Heating (1)
- Long-term space mission (1)
- Magnetic shielding (1)
- Magnetorquer (1)
- Membranes (1)
- Microbial Check Valve (1)
- Mu-Metal (1)
- Nichrome (1)
- Orbit Analysis (1)
- Orbital Decay (1)
- Silver Ions (1)
- Silver biocide (1)
- Space exploration (1)
- Spacecraft water management (1)
- Tungsten (1)
- Water Filtration (1)
- Water Processing Assembly (1)
- Water recovery system (1)
- Xenon Difuloride (1)
Articles 1 - 7 of 7
Full-Text Articles in Engineering
A Systematic Study Into The Design And Utilization Of Burn Wire As A Means Of Tensioning And Releasing Spacecraft Mechanisms Through Applied Joule Heating, Chandler Dye
Mechanical Engineering Undergraduate Honors Theses
The joule heating characteristics of Nichrome burn wires, often used as a thermal cutting device in mechanisms designed to fasten and release CubeSat deployables, are examined in the following thesis. Wires ranging from 0.125 inches to 2 inches long, and diameters of 30 Ga and 40 Ga, are investigated through analytical calculations and thermal simulations based on heat transfer due to joule heating, and through physical circuitry-based experiments. The temperature data is used to generate heating curves to predict the time it takes for Nichrome wires to fail under varying testing parameters. This research aims to catalog a series of …
Orbital Debris Analysis And Orbital Decay Analysis Of Arksat-2, Will Stuff
Orbital Debris Analysis And Orbital Decay Analysis Of Arksat-2, Will Stuff
Mechanical Engineering Undergraduate Honors Theses
ARKSAT-2 is a cube satellite developed by the University of Arkansas for its second CubeSat mission. There are two objectives of the ARKSAT-2 mission. The first objective of this mission is to test a novel cold gas thruster propulsion system using water-propylene propellant. This propulsion system will be used for attitude control of the satellite. The second objective for the ARKSAT-2 mission is to test a Solid-State Inflation Balloon (SSIB) that has been designed and developed for this mission. The SSIB is designed to be a simple and cost-effective method for deorbiting the vehicle. In cube satellites, a software known …
Preliminary Development Of The Dialysis-Membrane-Based Passive Biocide Delivery System For Spacecraft Water Recovery Units, Rogelio Elias Garcia Fernandez
Preliminary Development Of The Dialysis-Membrane-Based Passive Biocide Delivery System For Spacecraft Water Recovery Units, Rogelio Elias Garcia Fernandez
Graduate Theses and Dissertations
The purpose of this investigation is to explore the capabilities of a dialysis-membrane-based system for the in-line dosing of silver ions to treated water in spacecraft water recovery units. The spacecraft environmental control and life support system community (ECLSS) are interested in adopting silver ions as a biocide in future spacecraft water recovery processes since silver ions are effective biocide at concentrations that humans can safely consume. The system has been designed following the configuration of the Water Processor Assembly (WPA) aboard the International Space Station. In this configuration, silver ions have to be added at the last step in …
Attitude Determination And Control Of Arksat-1, Jared Gilliam
Attitude Determination And Control Of Arksat-1, Jared Gilliam
Mechanical Engineering Undergraduate Honors Theses
ARKSAT-1 is a nanosatellite developed at the University of Arkansas as part of NASA’s CubeSat Launch Initiative (CSLI). The goal of ARKSAT-1 is to utilize an LED emitter paired with a ground-based tracking system to perform measurements of the composition of the atmosphere using spectroscopy. As part of its function, it is imperative that the satellite is able to control its orientation so that the emitter is aligned as closely as possible with the ground tracker. To do this, the attitude control system of ARKSAT-1 uses magnetic actuators to create a torque on the satellite by interacting with Earth’s magnetic …
Development Of High-Density Propulsion System Technologies For Interplanetary Small Satellites And Cubesats, Morgan Andrew Roddy
Development Of High-Density Propulsion System Technologies For Interplanetary Small Satellites And Cubesats, Morgan Andrew Roddy
Graduate Theses and Dissertations
The goal of this research was to support the development of a novel propulsion system for small satellites (<180 kg) and CubeSats. This was pursued by conducting a collection of studies that were designed to provide engineering data that would be critical in designing a functional prototype. The novel propulsion system was conceived by the author to provide best-in-class performance for the small satellite and CubeSat families of spacecraft. This context presents specific design requirements that the presented technology attempts to satisfy. The most critical among these is high density; the propellant was designed to be stored with high density and the thruster was designed to be as compact as possible. The propulsion system is composed of two primary elements, a propellant generator and a thruster. The propellant generator works by sublimating a solid crystal into vapor and then using this vapor to etch a dense metal. The resulting gaseous byproducts of this reaction are the propellant. This dissertation used xenon difluoride (XeF2) vapor to etch tungsten (W) which react to form xenon gas (Xe) and tungsten hexafluoride (WF6). This approach gave a theoretical propellant storage density 5.40 g/cm3; and 5.17 g/cm3 was demonstrated. The sublimation dynamics of the XeF2 were studied as a function of surface area and temperature and it was found to be suitable for the intended application due to its high effluence rate; that is, it sublimates fast enough to be useful. The sublimation rates are on the order of 10’s of µg/s. The etch rate of XeF2 on W was also studied and found to be suitably fast to provide useful amounts of reactants for use as a propellant, again on the order of 1’s of µg/s. The thruster is an electrostatic radio frequency (RF) ion thruster design and is manufactured with Low Temperature Co-Fired Ceramic (LTCC) materials system and manufacturing technology. Manufacturing samples of the thruster were built at the University of Arkansas in July 2015 and tested at NASA’s Marshall Space Flight Center in May 2018. Testing validated the viability of the LTCC thruster and provided valuable information on how to improve the thruster’s design.
Task 1: Silver-Based Microbial Check Valve For Spacecraft Potable Water Systems, Eric Beitle
Task 1: Silver-Based Microbial Check Valve For Spacecraft Potable Water Systems, Eric Beitle
Chemical Engineering Undergraduate Honors Theses
As human space exploration increases, the development of a more efficient potable water treatment system suited for spacecraft becomes crucial. This Waste-management Education Research Consortium (WERC) challenge was designed to explore the viability of microbial control through the utilization of silver ions as a biocide for possible integration into the Tranquility Node 3 water purification system aboard the International Space Station (ISS). Current systems using iodine risk causing hyperthyroidism from overexposure; however, silver can be safely ingested without this side effect. After researching silver delivery methods including electrochemical ion production, controlled release, or a combination of the two, our team …
Active Permanent Magnet Attitude Control For Cubesats Using Mu-Metal Shielding, Maxwell Martin
Active Permanent Magnet Attitude Control For Cubesats Using Mu-Metal Shielding, Maxwell Martin
Mechanical Engineering Undergraduate Honors Theses
Cube-Satellites (CubeSats) are nanosatellites composed of cube shaped units, each nominally 10cm to a side and around 1kg in mass. Due to their inherent size and weight limitations, it is often impractical to use conventional attitude, or rotational, control methods such as thrusters on these small satellites. Several methods, including magnetorquer rods and small reaction wheels, are often used instead of traditional methods to work around the size and weight limitations. As a new alternative to these methods, a permanent magnet mounted on a rotatable shaft could be used to achieve attitude control. In much the same way that a …