Engineering Commons^™

Cutting-Edge Technologies To Achieve A Higher Level Of Modular Construction – Literature Review, Seungtaek Lee, Jin Ouk Choi, Seung Song

Civil and Environmental Engineering and Construction Faculty Research

Cost overruns, schedule delays, and a shortage of skilled labor are common problems the construction industry is currently experiencing. Modularization and standardization strategies have the potential to resolve the various problems mentioned above and have been applied for various construction applications for a long time. However, the level of modularization remains low, and modular construction projects have not been getting the full benefits. Thus, this review investigated the cutting-edge technologies currently being utilized to develop the modular construction field. For this paper, qualified research papers were identified using predetermined keywords from previous related research papers. Identified literature was then filtered …

The Current State And Future Directions Of Industrial Robotic Arms In Modular Construction, Seung Ho Song, Jin Ouk Choi, Seungtaek Lee

Civil and Environmental Engineering and Construction Faculty Research

Industrial robotic arms are widely adopted in numerous industries for manufacturing automation under factory settings, which eliminates the limitations of manual labor and provides significant productivity and quality benefits. The U.S. modular construction industry, despite having similar controlled factory environments, still heavily relies on manual labor. Thus, this study investigates the U.S., Canada, and Europe-based leading modular construction companies and research labs implementing industrial robotic arms for manufacturing automation. The investigation mainly considered the current research scope, industry state, and constraints, as well as identifying the types and specifications of the robotic arms in use. First, the study investigated well-recognized …

Design Concepts And Process Analysis For Transmuter Fuel Manufacturing, Georg F. Mauer

Fuels Campaign (TRP)

The safe and effective manufacturing of actinide-bearing fuels for any transmutation strategy requires that the entire manufacturing process be contained within a shielded hot cell environment. To ensure that the fabrication process is feasible, the entire process must be designed for remote operation. The equipment must be reliable enough to perform over several decades, and also easy to maintain or repair remotely. The facility must also be designed to facilitate its own decontamination and decommissioning. In addition to these design factors, the potential viability of any fuel fabrication process will also be impacted by a number of variables, such as …

Design Concepts And Process Analysis For Transmuter Fuel Manufacturing, Georg F. Mauer

Fuels Campaign (TRP)

The safe and effective manufacturing of actinide-bearing fuels for any transmutation strategy requires that the entire manufacturing process be contained within a shielded hot cell environment. To ensure that the fabrication process is feasible, the entire process must be designed for remote operation. The equipment must be reliable enough to perform over several decades, and also easy to maintain or repair remotely. The facility must also be designed to facilitate its own decontamination and decommissioning. In addition to these design factors, the potential viability of any fuel fabrication process will also be impacted by a number of variables, such as …

A Fuzzy Logic Controller For Autonomous Wheeled Vehicles, Mohamed Trabia, Linda Z. Shi, Neil Eugene Hodge

Mechanical Engineering Faculty Research

Autonomous vehicles have potential applications in many fields, such as replacing humans in hazardous environments, conducting military missions, and performing routine tasks for industry. Driving ground vehicles is an area where human performance has proven to be reliable. Drivers typically respond quickly to sudden changes in their environment. While other control techniques may be used to control a vehicle, fuzzy logic has certain advantages in this area; one of them is its ability to incorporate human knowledge and experience, via language, into relationships among the given quantities. Fuzzy logic controllers for autonomous vehicles have been successfully applied to address various …

Design Concepts And Process Analysis For Transmuter Fuel Manufacturing: Quarterly Progress Report #6, Kamalakar Alluri, Georg F. Mauer

Fuels Campaign (TRP)

Project Milestones

• Completed a systematic study seeking to arrive at an optimized plant configuration, using value engineering techniques in January 2006.

• Vision-based robot serving and automated plant safety monitoring is currently in progress.

Design Concepts And Process Analysis For Transmuter Fuel Manufacturing, Georg F. Mauer

Fuels Campaign (TRP)

The safe and effective manufacturing of actinide-bearing fuels for any transmutation strategy requires that the entire manufacturing process be contained within a shielded hot cell environment. To ensure that the fabrication process is feasible, the entire process must be designed for remote operation. The equipment must be reliable enough to perform over several decades, and also easy to maintain or repair remotely. The facility must also be designed to facilitate its own decontamination and decommissioning. In addition to these design factors, the potential viability of any fuel fabrication process will also be impacted by a number of variables, such as …

Design Concepts And Process Analysis For Transmuter Fuel Manufacturing: Quarterly Progress Report #1, Jamil M. Renno, Georg F. Mauer

Fuels Campaign (TRP)

A Hot Cell robotic assembly: Pick and place dynamic simulation, including feedback control with Matlab, was developed for dispersion fuel manufacture.

The deployment of remote manufacturing of transmuter fuel is a necessity for the transmutation applications. In the reporting period, a virtual hot cell for the manufacturing of dispersion fuel was designed using MSC.visualNastran^©, ProEngineer^© and MATLAB^©. Atypical events were successfully simulated. Relevant physical quantities arising during such events were monitored as well.

Design And Evaluation Of Processes For Fuel Fabrication, Georg F. Mauer

Fuels Campaign (TRP)

The goal of this research project was to provide technical support to process designers working on the development of the fuel cycles for transmutation applications. Detailed process models were developed to better define the impact of fuel choice on the transmuter fuel cycle, including relative process losses, waste generation, and plant capital cost. These process models provide insight regarding required plant size and number of plants needed to mesh with the fuel recycling line. They also determine requirements for automation.

Manufacturing models for large-scale production in a hot cell environment were also developed. Combined, these two models allow the assessment …

Design And Evaluation Of Processes For Fuel Fabrication: Quarterly Progress Report #11, Georg F. Mauer

Fuels Campaign (TRP)

The eleventh quarter of the project covered the following:

• Mr. Richard Silva successfully defended his thesis in April 2004 and graduated from the MEG Master’s program.

• Further refinements on Concepts and Methods for Vision-Based Hot Cell Supervision and control, focusing on rule-based object recognition (Ph.D. Graduate Jae-Kyu Lee). Ms. Caroline Wiejak, an exchange student from the ESIEE in Marne-la-Vallee, France is continuing with the image analysis effort. To date, she has transferred Jae-Kyu’s code to Matlab, and is presently expanding its application to more complex 3D shapes.

• Graduate student Jamil Renno refined and detailed his simulations of …

Design And Evaluation Of Processes For Fuel Fabrication: Quarterly Progress Report #10, Georg F. Mauer

Fuels Campaign (TRP)

The tenth quarter of the project covered the following:

• Mr. Richard Silva continued the development of a simulation model with a Waelischmiller hot cell robot, and is close to completing his M.Sc. thesis project. Rich will likely defend his thesis in April 2004.

• A project review meeting with Dr. Mitch Meyer and other ANL scientists was held in December 2003 at ANL West, Idaho Falls, ID. Dr. Meyer described ANL long term research objectives with regard to transmuter fuel manufacturing.

• Further refinements on Concepts and Methods for Vision-Based Hot Cell Supervision and control, focusing on rule-based object …

Design And Evaluation Of Processes For Fuel Fabrication: Quarterly Progress Report #10, Georg F. Mauer

Fuels Campaign (TRP)

The tenth quarter of the project covered the following:

• Mr. Richard Silva continued the development of a simulation model with a Waelischmiller hot cell robot, and is close to completing his M.Sc. thesis project. Rich will likely defend his thesis in April 2004.

• A project review meeting with Dr. Mitch Meyer and other ANL scientists was held in December 2003 at ANL West, Idaho Falls, ID. Dr. Meyer described ANL long term research objectives with regard to transmuter fuel manufacturing.

• Further refinements on Concepts and Methods for Vision-Based Hot Cell Supervision and control, focusing on rule-based object …

Design And Evaluation Of Processes For Fuel Fabrication, Georg F. Mauer

Fuels Campaign (TRP)

The goal of this research project is to provide technical support to process designers working on the development of the fuel cycles for transmutation applications. Detailed process models are developed to better define the impact of fuel choice on the transmuter fuel cycle, including relative process losses, waste generation, and plant capital cost. These process models provide insight regarding required plant size and number of plants needed to mesh with the fuel recycling line. They also determine requirements for automation.

Manufacturing models for large-scale production in a hot cell environment are also developed. Combined, these two models allow the assessment …

Design And Evaluation Of Processes For Fuel Fabrication: Quarterly Progress Report #9, Georg F. Mauer

Fuels Campaign (TRP)

The ninth quarter of the project covered the following:

• Mr. Richard Silva continued the development of a simulation model with a Waelischmiller hot cell robot. Rich will continue to develop detailed 3-D process simulation models as his M.Sc. thesis project.

• A paper on hot cell robotics was presented at the ANS Winter Annual Meeting and published in the ANS 2003 conference proceedings.

• Further advances on Concepts and Methods for Vision-Based Hot Cell Supervision and control, focusing on rule-based object recognition (Ph.D. Student Jae-Kyu Lee)

• Graduate student Jamil Renno created simulations of more complex fuel manufacturing and …

Design And Evaluation Of Processes For Fuel Fabrication: Quarterly Progress Report #8, Georg F. Mauer

Fuels Campaign (TRP)

The eighth quarter of the project covered the following:

· Mr. Richard Silva continued the development of a simulation model with a Waelischmiller hot cell robot. Rich will continue to develop detailed 3-D process simulation models as his M.Sc. thesis project.

· A paper submitted for ANS for the Winter Annual Meeting on hot cell robotics was accepted for presentation and publication.

· Further advances on Concepts and Methods for Vision-Based Hot Cell Supervision and control, focusing on rule-based object recognition (Ph.D. Student Jae-Kyu Lee)

· Undergraduate student Jamil Renno created simulations of fuel pin assembly (robotic insertion of pellets …

Design And Evaluation Of Processes For Fuel Fabrication: Quarterly Progress Report #7, Georg F. Mauer

Fuels Campaign (TRP)

The seventh quarter of the project covered the following:

• Mr. Richard Silva continued the development of a simulation model with a Waelischmiller hot cell robot. Rich will continue to develop detailed 3-D process simulation models as his M.Sc. thesis project.

• Mr. Richard Silva presented a paper on hot cell robotics at the ANS student conference in Berkeley, CA.

• Concepts and Methods for Vision-Based Hot Cell Supervision and control, focusing on rule-based object recognition (Ph.D. Student Jae-Kyu Lee)

• Undergraduate student Jamil Renno, developed better control algorithms, and created simulations of pick and place actions for the hot …

Design And Evaluation Of Processes For Fuel Fabrication: Quarterly Progress Report #6, Georg F. Mauer

Fuels Campaign (TRP)

The sixth quarter of the project covered the following:

• Mr. Richard Silva continued the development of a simulation model with a Waelischmiller hot cell robot. Rich will continue to develop detailed 3-D process simulation models as his M.Sc. thesis project. Rich is employed with Bechtel at the Yucca Mountain project.

• Concepts and Methods for Vision-Based Hot Cell Supervision and control (Ph.D. Student Jae-Kyu Lee )

• An undergraduate senior student in mechanical engineering, Mr. Jamil Renno, was hired to develop the simulation model for the hot cell manipulator.

Design And Evaluation Of Processes For Transmuter Fuel Fabrication, Georg F. Mauer

Fuels Campaign (TRP)

• Project Objective: examine autonomous robotic fuel fabrication processes with regard to hot cell and equipment design, operations, and costs.

• Fabrication processes for different fuel types differ in terms of equipment types, throughput, and cost.

• Design options are restricted by the requirement to employ only radiation-hardened machinery and components

• Benefit to Department of Energy: decision support for the selection of the most suitable manufacturing process.

Design And Evaluation Of Processes For Fuel Fabrication: Quarterly Progress Report #5, Georg F. Mauer

Fuels Campaign (TRP)

The fifth quarter of the project covered the following:

· Literature Search: The process of evaluating the pertinent literature continued.

· Mr. Richard Silva continued the development of a simulation model with a Waelischmiller hot cell robot. Rich will continue to develop detailed 3-D process simulation models as his M.Sc. thesis project.

· Dr. Mauer presented a paper at the ANS Winter annual meeting in Washington, D.C. titled: “Design and Evaluation of Processes for Transmuter Fuel Fabrication.”

· Concepts and Methods for Vision-Based Hot Cell Supervision and control (Ph.D. Student Jae-Kyu Lee )

· Dr. Mauer presented a paper at …

Design And Evaluation Of Processes For Fuel Fabrication: Quarterly Progress Report #4, Georg F. Mauer

Fuels Campaign (TRP)

The fourth quarter of the project covered the following:

• Literature Search: The process of evaluating the pertinent literature continued. Results are summarized.

• Mr. Richard Silva developed a simulation model with a Waelischmiller hot cell robot. Rich will continue to develop detailed 3-D process simulation models as his M.Sc. thesis project.

• Dr. Mauer visited CEA Cadarache and CEA Marcoule in France, the institute for transuranics in Karlsruhe, and the Framatome manufacturing plant in Lingen, Germany.

• Concepts and Methods for Vision-Based Hot Cell Supervision and control (Ph.D. Student Jae-Kyu Lee )

Design And Evaluation Of Processes For Fuel Fabrication: Year 1 Final Report, Georg F. Mauer

Fuels Campaign (TRP)

The project objective is the design and evaluation of manufacturing processes for transmuter fuel fabrication. The large-scale deployment of remote fabrication and refabrication processes will be required for all transmutation scenarios. Current program emphasis is on a five-year effort to determine the feasibility of transmutation as a technology to limit the need for repository storage of spent commercial fuel. The evaluation of the fabrication processes will create a decision support data base to document design, operations, and costs. Fabrication processes required for different fuel types differ in terms of equipment types, throughput, and cost. The year 1 project was focused …

Design And Evaluation Of Processes For Fuel Fabrication: Year 1 Final Report, Georg F. Mauer

Fuels Campaign (TRP)

The project objective is the design and evaluation of manufacturing processes for transmuter fuel fabrication. The large-scale deployment of remote fabrication and refabrication processes will be required for all transmutation scenarios. Current program emphasis is on a five-year effort to determine the feasibility of transmutation as a technology to limit the need for repository storage of spent commercial fuel. The evaluation of the fabrication processes will create a decision support data base to document design, operations, and costs. Fabrication processes required for different fuel types differ in terms of equipment types, throughput, and cost. The year 1 project was focused …

Design And Evaluation Of Processes For Fuel Fabrication, Georg F. Mauer

Fuels Campaign (TRP)

One of the primary concerns in selecting a fuel matrix for actinide-bearing fuels, such as those for transmutation systems, is fuel fabrication. Fuel fabrication technologies for the fabrication and re-fabrication processes must meet several technical considerations, such as minimizing secondary radioactive waste streams, economic viability, reasonable capital outlay, and must be easy to maintain over the transmuter core life cycle. Additionally, the fuel type chosen must be easily manufactured in a remote environment. The volatile behavior of americium during thermal processing further complicates these goals. Currently, the national program is investigating a number of candidate fuel matrices: metallic, ceramic, dispersion, …

Comparison Of Two Distributed Fuzzy Logic Controllers For Flexible-Link Manipulators, Linda Z. Shi, Mohamed Trabia

Mechanical Engineering Faculty Presentations

The paper suggests that fuzzy logic controllers present a computationally efficient and robust alternative to conventional controllers. The paper presents two possible structures for the distributed fuzzy logic controller of a single-link flexible manipulator. A linear quadratic regulator method is used to prove the effectiveness of fuzzy logic controllers.

Variable Structure End Point Control Of A Flexible Manipulator, Shailaja Chenumalla, Sahjendra N. Singh

Electrical & Computer Engineering Faculty Research

We treat the question of control and stabilization of the elastic multibody system developed in the Phillips Laboratory, Edwards Air Force Base, California. The controlled output is judiciously chosen such that the zero dynamics are stable or almost stable. A variable structure control (VSC) law is derived for the end point trajectory control. Although, the VSC law accomplishes precise end point tracking, elastic modes are excited during the maneuver of the arm. A Linear stabilizer is designed for the final capture of the terminal state.