Engineering Commons^™

Dc To Ac Inverter For A Microgrid-Inspired Power Distribution Architecture For Electric Vehicles, Bryan A. Carrillo Martinez, Eli Blacklock, Paul A. Samson, William S. Holt-Hillis

Electrical Engineering

This project builds upon the prototyping of a microgrid-inspired power distribution architecture for electric vehicles (EVs). The efficacy of this prototype aims to inform a full-scale power distribution system that charges an EV battery, supports the electric grid with important ancillary services, performs peer-to-peer EV charging, and works in conjunction with other AC and DC sources and loads. The scope of this report focuses specifically on the design, construction, and testing of the DC/AC inverter. Future development of this distribution architecture will incorporate synchronous generators, a battery management system, and an Arduino/Raspberry Pi-based communication system to fully simulate an electric …

Smart Usb-C Wall Plug For The Dc House Project, Ridge Lahti, Dino Maslic

Electrical Engineering

DC operated devices and appliances powered by AC systems suffer inefficiencies resulting from the losses of converting AC energy into DC energy. At Cal Poly, the DC House Project aims to minimize the need for AC electricity in homes and encourage the use of renewable energy systems. The DC House uses a 48V DC bus that must be stepped down for use with increasing number of DC loads in a typical home. In this project, a Smart USB-C Wall Plug is designed to work with USB Power Delivery to provide a variable voltage output for use with these DC loads …

Current-Source Dc-Dc Converter For Fiber-Optic Communication Systems, Jissell C. Jose

Master's Theses

In this thesis, a proof of concept for a current-source DC-DC converter for powering sensors used in an underwater communications system is presented. The proposed converter steps down an input current of 0.9 A to 0.625 A, while maintaining an output voltage of 24 V and output power of 15 W. The complete steady-state analysis and design of the proposed converter in its single-stage form is also explained in detail. Performance evaluation of the proposed converter was carried out using LTspice. Results of the simulation demonstrate that the design was able to produce average output current of 0.639 A at …

Multiple Input Single Output Converter With Uneven Load Sharing Control For Improved System Efficiency, Kristen Y. Chan

Master's Theses

This paper presents the development and study of multiple-input single-output converter (MISO) for the DC House project that utilizes a controller to maximize the overall converter’s efficiency. The premise of this thesis is to create uneven load current sharing between the converters at different loading conditions in order to maximize the efficiency of the overall MISO converter. The goal is to find a proper ratio of current from each converter to the total load current of the MISO system to achieve the greatest efficiency. The Arduino microcontroller is implemented to achieve this goal. The design and operation of the MISO …

Cascaded Linear Regulator With Negative Voltage Tracking Switching Regulator, Ernest Lei

Master's Theses

DC-DC converters can be separated into two main groups: switching converters and linear regulators. Linear regulators such as Low Dropout Regulators (LDOs) are straightforward to implement and have a very stable output with low voltage ripple. However, the efficiency of an LDO can fluctuate greatly, as the power dissipation is a function of the device’s input and output. On the other hand, a switching regulator uses a switch to regulate energy levels. These types of regulators are more versatile when a larger change of voltage is needed, as efficiency is relatively stable across larger steps of voltages. However, switching regulators …

Flexible Custom Electric Skateboard, Caleb Adam Kelsay

Electrical Engineering

At Cal Poly traveling long distances only accessible by foot such as across campus or from the car park to class can be tiring and time-consuming. While not physically demanding, the trek consumes time in our tight college life schedule. To improve our time efficiency this project provides a relatively lightweight, powered solution to quickly and effectively travel long distances while maintaining full control and safety even on hills, a current limitation of traditional skateboards.

This electric skateboard includes the battery capacity to travel all around campus on a single charge with a compact and flexible skateboard design that provides …

The Zephyr Charge: A Wind-Powered Usb Charger, James Dean Carson, John Pina Lopez Iii

Electrical Engineering

The Zephyr Charge project is to design and build a cell phone charger using a small wind turbine generator that can be useful to the fishermen community, namely fishermen of third world countries. The generator will output to USB for ease of charging capability. The size of the whole system should be light enough to move around, and the turbine itself will be mountable onto an edge of a wall. The goal of this project is to design and build a compact and easy to use cell phone charger, which is also efficient.

In order to be a practical product, …

Human-Powered Swing Generator, Danny Cai, Timothy Lai, Brandon Wong

Electrical Engineering

Many developing countries lack sufficient resources to provide enough electricity for every family to live with a satisfying level of comfort and convenience. Our project proposes a solution that provides families with an alternative access to electricity using a playground swing. This project addresses the design and construction of the Human-Powered Swing Generator, which converts mechanical energy to electrical energy for charging a battery. The charged battery serves as a source of DC energy for potential DC purposes, such as charging a cell phone.

Smart Wall Outlet Design And Implementation For The Dc House Project, Kevin Roy Mendoza

Master's Theses

Most everyday AC appliances are designed to operate off of 120V coming from the wall outlet in our homes. This voltage is a standard set from our established infrastructure. Unlike AC devices, DC devices do not have any set standard of voltage they all will run off of. This presents a problem for the DC house as the various loads that will be used will have different required input voltages. One set voltage for a wall outlet will not suffice for the DC House. This Smart Wall Outlet is designed with a DC-DC converter that will have its output voltage …

Efficiency Performance Improvement Using Parallel Dc-Dc Converters With A Digital Controller, Daniel Forbes

Master's Theses

A system to improve efficiency performance of a DC-DC converter is simulated and built. The proposed system combines multiple DC-DC converters in parallel and implements a digital control scheme and load-share controller. A model of the system is developed in MATLAB Simulink and the model demonstrates the improved converter’s efficiency particularly at low load conditions. This simulation is then designed into a hardware system running three DC-DC converters in parallel, controlled by a microcontroller and a load-share controller. The hardware also confirms the simulation results, although some hardware refinements are evident as simulation results are superior. The system is designed …

Imu Integration To The Cal Poly Spacecraft Attitude Dynamics Simulator Power System, Wayland Chan

Electrical Engineering

The Cal Poly Spacecraft Attitude Dynamics Simulator mimics the rotation dynamics of a spacecraft in orbit and acts as a test bed for spacecraft attitude control system development and demonstration. Prior to this project, the simulator measured its attitude dynamics from a total of seven sensors mounted on to the platform, including three micro-electromechanical system (MEMs) gyroscopes, and four motor encoders. This project entails the installation of an LN-200 high performance gyroscope, which will provide a greater measure of accuracy. The goal of this project is to design a power circuit that will integrate the LN-200 inertial measurement unit onto …

Design And Analysis Of A Wind Energy Harvesting Circuit Using Piezoelectric Polymers, Jameson J. Thornton

Master's Theses

This thesis investigates a relatively new method for harvesting wind energy by using flexible piezoelectric polymers with additional sails to increase their ability to harvest wind energy. This paper also introduces a new topology deemed the “stacked buck” that allows for multiple inputs to a system with a single output. Derivations and analysis detail the workings of the “stacked buck” with a laboratory test to show a working model. This paper also reports another experiment done in a wind tunnel to analyze the capability of the piezoelectric polymers as sources to the “stacked buck” topology with measurements of the power …

Modular Electronic Load, Jason March

Electrical Engineering

This project entails the design and development of a modular electronic load. The cost and simplicity of the design are considered such that it can be reproduced in-house to replace whenever possible resistor box for load testing of any analog circuits but more specifically power electronic circuits.

The design process as well as the hardware development is explained in details in this report. Results from hardware testing are also provided.

An Expandable Micromotor Dc Drive System, Michael Ruelan, Justin Gragg

Electrical Engineering

This report documents the design phases and fabrication of an expandable micro-motor DC drive system. This project illustrates that a flexible range of output power demands can be met from a small DC micro-motor drive unit with the use of power electronics.

In this project miniature DC micromotor drives, each capable of drawing up to 5.5 amps rated current (5 amps due to the utilization of a 5 amp fuse), were designed as card inserts that can be conveniently inserted in parallel in to a cardholder within the console. The “insert” feature allowed our console to successfully draw up to …

High Voltage Resonant Self-Tracking Current-Fed Converter, Scott Logan Mcclusky

Master's Theses

High voltage power supply design presents unique requirements, combining safety, controllability, high performance, and high efficiencies. A new Resonant Self-Tracking Current-Fed Converter (RST-CFC) is investigated as a proof-of-concept of a high voltage power supply particularly for an X-ray system. These systems require fast voltage rise times and low ripple to yield a clear image.

The proposed converter implements high-frequency resonance among discrete components and transformer parasitics to achieve high voltage gain, and the self-tracking nature ensures operation at maximum gain while power switches achieve zero-voltage switching across the full load range. This converter exhibits an inherent indefinite short-circuit capability. Theoretical …

Harmonic Analysis Of A Static Var Compensated Mixed Load System, James David Ruckdaschel

Master's Theses

As power electronic based controllers and loads become more prevalent in power systems, there is a growing concern about how the harmonics generated by these controllers and loads affect the power quality of the system. One widely used power electronic based load is the Variable Frequency Drive (VFDs) used to vary the speed of an induction motor; whereas a common example of a power electronic based controller used in power systems is the Static VAR Compensator (SVC) for improving a system’s power factor. In this thesis, the harmonic content and overall performance of a system including both a VFD and …