Engineering Commons^™

Direct Ink Writing Of Flexible Piezoelectric Sensors, Amanda M. White

Boise State University Theses and Dissertations

Piezoelectric poly(vinylidene fluoride-co-trifluoroethylene), or PVDF-trFE, builds up significant electrical charges on its surface when stressed. By correlating the mechanical force with the resulting electrical charges or voltages, researchers have developed flexible, broadband, and biocompatible force sensors. PVDF-trFE force sensors are traditionally fabricated via spin coating or solvent casting, which result in large waste production and experience difficulties in forming complex geometries. To tackle these challenges, I leveraged a commercial direct ink writing system (nScrypt microdispenser) to additively manufacture PVDF-trFE force sensors. I first synthesized an unprecedented piezoelectric ink that is compatible with a commercial ink writing system at Boise State …

A Numerical Simulation Of The Powder Bed Additive Manufacturing Process With Molecular Dynamics Simulation, Yeasir Mohammad Akib

Theses and Dissertations

Many manufacturing industries utilize powder bed fusion (PBF) since it can produce microscale precision 3D parts. During PBF, powder particles are selectively fused layer by layer using thermal energy. The build quality in the PBF process relies heavily on powder bed properties and thermal energy deposition. Powder flowability, spreadability, and packing fraction are some of the insightful factors that determine the quality of the powder bed. In this study, a two-dimensional powder bed is developed using the LAMMPS package. A cloud-based pouring of powders with varying volumes and initialization is adopted for the work. A blade-type and circular recoater is …

Optimized 3d-Printing Of Carbon Fiber-Reinforced Polyether-Ether-Ketone (Cfr-Peek) For Use In Overmolded Lattice Composite, Ryan C. Ogle

Masters Theses

Current orthopedic implants are overwhelmingly composed from metallic materials. These implants show superior mechanical properties, but this can additionally result in stress shielding due to a modulus mismatch between the bone tissue and implanted device. Polymeric implants reduce this stress shielding effect but have much lower mechanical properties, limiting their use. Polylactic acid (PLA) is a widely used biodegradable thermoplastic polymer, however, its use has been limited by the polymer’s mechanical properties and rapid loss of strength during degradation in vivo. Polyether-ether-ketone (PEEK) is another common biocompatible polymer , with chemical and mechanical properties which make it a popular alternative …

Characterization Of Materials Properties In Additively Manufactured Aisi-420 Martensitic Steel Deposited By Laser Engineered Net Shaping, Md Mehadi Hassan

Nanoscience and Microsystems ETDs

Metal additive manufacturing (AM) is a disruptive technology enabling the fabrication of complex and near-net-shaped parts by adding material layer-wise. It offers reduced lead production time. AM processes are finding applications in many industrial sectors such as aerospace, automotive, biomedical, and mold tooling. Despite the tremendous advantages of AM, some challenges still prevent this technology's adoption in high-standard applications. Anisotropy and inhomogeneity in the mechanical properties of the as-built parts and the existence of pores and lack-of-fusion defects are considered the main issues in directed energy deposition (L-DED) parts. Laser-engineered net shaping LENS® offers excellent possibilities to fabricate metal tools …

Additive Manufacturing Of Molybdenum For High Temperature Structural Applications, Megan L. Bustin

Theses and Dissertations

This research considered additive manufactured (AM) molybdenum (Mo) and the effect of three variables on microstructure, mechanical properties, and the relationship between the two. Test temperature, laser speed, and shield gas or build atmosphere were varied, and samples tested and analyzed using a three-point bending test, chemical composition, and optical and scanning electron microscopy. The relationship among variables and results using a Design of Experiments was limited compared to the inclusion of every tested sample. Most effects were expected: samples tested at room temperature were brittle without statistical significance; increasing laser speed resulted in decreased ductility and strain, smaller grain …

Additively Manufactured Polymer And Metal Lattice Structures With Eulerian Path, Adeeb Ibne Alam

Electronic Theses and Dissertations

Lattice structure manufacturing with polymers and metals can benefit from the use of Eulerian paths. In this research, two types of lattice fabrication methods are studied where the Eulerian path can be applicable. Polymer lattice is improved by using a new assembly design, while a new way of metal lattice fabrication is discussed.

For the fused filament fabrication process, a new interlocking design and assemble-based lattice structure building approach is investigated by increasing continuity in layers and avoiding support structures. To minimize contour plurality, Eulerian paths between the edges were enforced. Two configurations in the form of cubic and octet …

Ferrous Alloy Manufacturing For The Martian Surface Through In-Situ Resource Utilization With Ionic Liquids Harvested Iron And Bosch Process Carbon, Blake C. Stewart

Theses and Dissertations

As research continues for the habitation of the Lunar and Martian surfaces, the need for materials for construction of structural parts, mechanical components, and tools remains as a major milestone. The use of in-situ resource utilization (ISRU) techniques is critical due to the financial, physical, and logistical burdens of sending supplies beyond low-Earth orbit. The Bosch process is currently in development as a life support system at the National Aeronautics and Space Administration’s (NASA) Marshall Space Flight Center (MSFC) to regenerate oxygen (O2) from metabolic carbon dioxide (CO2) with the byproduct of elemental carbon (C). The Bosch process presents a …

Flow And Thermal Transport In Additively Manufactured Metal Lattices Based On Novel Unit-Cell Topologies, Inderjot Kaur

Theses and Dissertations

The emergence of metal Additive Manufacturing (AM) over the last two decades has opened venues to mitigate the challenges associated with stochastic open-cell metal foams manufactured through the traditional foaming process. Regular lattices with user-defined unit cell topologies have been reported to exhibit better mechanical properties in comparison to metal foams which extend their applicability to multifunctional heat exchangers subjected to both thermal and mechanical loads. The current study aims at investigating the thermal-hydraulic characteristics of promising novel unit cell topologies realizable through AM technologies. Experimental investigation was conducted on four different topologies, viz (a) Octet, (b) Face-diagonal (FD) cube, …

The Temperature Dependent Mechanical Response Of M250 Maraging Steel And Its Implications On Wire Arc Additive Manufacturing, Frank M. Brinkley Iii

Theses and Dissertations

Wire-arc additive manufacturing (WAAM) is becoming increasingly common for large scale additive manufacturing (AM) applications because of its high deposition rate (2-3 kg/hr.). The rapid temperature changes and subsequent evolution of mechanical properties during AM can lead to large distortion and residual stresses. Finite element modeling of the AM process shows promise to minimize part distortion and residual stresses through improved path planning and process parameter optimization. However, accurate material properties of M250 before and after heat treatment are needed to properly characterize the property evolution from annealed to AM, to aged. Due to limited data on annealed M250, this …

Characterization Of 3d Printed Parts Containing Integrated Functionality Via Ultrasonically Embedded Wires, David Abraham Sepulveda

Open Access Theses & Dissertations

Material extrusion additive manufacturing has been widely adopted because it offers freedom of design, which allows complex geometry fabrication, and rapid prototyping. Interest in producing components with integrated functionality allowed forms of hybrid manufacturing to be developed such as the Multi3D system. This system produces parts with embedded components by combining additive, subtractive, soldering, dispensing, and embedding techniques. However, this involves pausing the printing process (which takes place in a controlled environment) and exposing it to ambient temperature where embedding takes places. In this research, the effect of embedding parts with 24 AWG copper for improved functionality was quantified mechanically. …

Characterization Of Fatigue Strength Of Additively Manufactured Ti-6al-4v With Recoater Blade Interference Flaws And Residual Stresses Towards An Enhanced Fatigue Substantiation Methodology For Aerospace Structures Applications, Joshua Manyara Mochache

Mechanical and Aerospace Engineering Dissertations

This research characterized the fatigue strength of additively manufactured (AM) Ti-6Al-4V, through fatigue and static tests conducted using specimens with and without recoater blade interference flaws (RBIF), and thus further enhanced the fatigue substantiation methodology for AM parts by using combined fatigue strength knock-down-factors (KDF) developed from this study. Qualification and certification (Q&C) of metallic AM parts, through acceptable methods for fatigue and damage tolerance (F&DT) substantiation, is an area where significant gaps still exist. While progress has been made in design as well as materials and process standardization, Q&C of additively manufactured metallic structural parts, especially those in civil …

Additive Manufacturing Of Aluminum Alloy By Metal Fused Filament Fabrication (Mf3)., Luke J. Malone

Electronic Theses and Dissertations

This research studies metal-fused filament fabrication (MF3) for manufacturing aluminum alloy parts. An aluminum alloy powder-based feedstock with a polymer-binder system was extruded via capillary rheometry to form a filament. The filament was used to print green parts that were involved in a two-step debinding process combining solvent and thermal extraction of the polymer binder, then sintered in a partial vacuum. Resulting grain structure, sintered density, and mechanical properties will be characterized and compared to metal injection molded (MIM) specimens. The main objective is to gain an understanding of the MF3 process characteristics and the ensuing material properties and microstructure …

Particle Formation And Thermal Radiation In Laminar Diffusion Flames With Applications To Energy And Materials, Phillip Irace

McKelvey School of Engineering Theses & Dissertations

Fossil fuels supply over 80% of the world’s primary energy, and if current policy and technology trends continue, global energy and energy-related carbon dioxide (CO2) emissions are predicted to increase for at least several decades owing to population and economic growth, leading to serious concerns regarding global warming. Natural gas releases less CO2 than other fossil fuels (e.g., coal and oil) and can help meet future CO2 emission targets. Natural gas combustion, however, has poor radiation heat transfer when compared to other fossil fuels owing to its low propensity for soot formation, making it difficult to use as a drop-in …

Additive Manufacturing Of Variable Contrast Computed Tomography Anatomical Phantoms Using A Single Feedstock In Fused Filament Fabrication, Cory J. Darling

University of New Orleans Theses and Dissertations

Anatomical phantoms used in biomedical education and training benefit greatly from Fused filament fabrication’s (FFF) ability to rapidly produce complex and unique models. Current materials and methods used in FFF have limited ability to accurately produce phantoms that can mimic the radiological properties of multiple biological tissues. This research demonstrates that the CT contrast of FFF produced models can be modified by varying the concentration of bismuth oxide in acrylonitrile butadiene styrene (ABS) filaments and a tunable CT contrast that mimics the CT contrast ranging from fatty tissue to cortical bone using a single composite filament without introducing artificial image …

Autonomous Material Refill For Swarm 3d Printing, William C. Jones

Mechanical Engineering Undergraduate Honors Theses

3D printing currently offers robust and cheap rapid prototyping solutions. While standard 3D printing remains at the periphery of mass production, the technology serves as a starting point for the development of swarm manufacturing. Since swarm manufacturing is predicated upon autonomy, swarm technology companies such as AMBOTS are seeking to minimize human involvement in the swarm’s functions. At present, the 3D printing swarm consists of the printers, a transporter which can take them between job sites, and the floor tiles which provide power and support the build surfaces. To add to this ecosystem, this project is focused on the design …

Effects Of Sizing Agents On Mechanical Properties Of Carbon Fiber–Polymer Composites Via Fused Filament Fabrication Additive Manufacturing., Benjamin D. Mitchell

Electronic Theses and Dissertations

This study demonstrated the effects of changing the sizing agent parameter during the preparation of carbon fibers on the mechanical properties of composite made with acrylonitrile butadiene styrene (ABS) as the matrix material and carbon fibers as the fiber material. Three types of sizing agents produced by Allnex were used to coat three different batches of carbon fibers that were mixed with a torque rheometer and extruded with a barrel-style melt extruder into continuous spools of 1.75 mm filament for use with commercial 3D printers. Tensile tests were conducted on the filaments and tensile bars printed from the materials. Results …

Multistage Modeling Of Fatigue Of Ti-6al-4v Fabricated By Different Additive Manufacturing Techniques, Lionardo Lado, Saeed Ataollahi, Mohammad J. Mahtabi

Honors Theses

Thanks to its high strength-to-weight ratio and corrosion resistance, Ti-6Al-4V has gained a lot of attention in additive manufacturing (AM) of complex parts with aerospace and medical applications. The realistic loading condition in these applications is mostly cyclic. However, the main challenge with AM of this alloy - and in general AM of metallic parts - is fatigue resistance and durability of the part, which has been reported to be much lower than the conventional materials. In this study, fatigue life performance of three additive manufacturing methods was compared using the Multistage Fatigue model (MSF). MSF model predicts the fatigue …

Effects Of Varied Oxygen Levels, Laser Powers, And Scanning Speeds On Manufactured Components By Laser-Based Powder Bed Fusion, Amelia Mcnamee

Honors College Theses

This project addresses the effects of oxygen concentration, laser power, and scanning speed on the melt pool geometry of laser-based powder bed fusion (L-PBF) additively manufactured components. A parametric analysis using the substrate alone was conducted to determine a range of desirable laser powers and scanning speeds. The parameter with the more significant effect will be decided upon based on the depth-to-width ratios (D/W) of the resultant laser weld bead. A range of oxygen levels and scan speeds was selected for the next phase. These samples were then be analyzed for depth-to-width ratios. It was expected that higher oxygen concentrations …

Effects Of A Nitrogen And Hydrogen Build Atmosphere On The Properties Of Additively Manufactured Tungsten, Dana C. Madsen

Theses and Dissertations

Additively manufactured tungsten was printed in pure nitrogen, nitrogen-2.5% hydrogen, and nitrogen-5% hydrogen atmospheres as part of a 2^3 full factorial designed experiment and subjected to room temperature and high-temperature three-point-bend testing, chemical analysis, hardness testing, and microstructural imaging techniques. The pure nitrogen specimens exhibited the highest strength and ductility at both high temperature and room temperature. Chemical analysis showed a 2-8x reduction in compositional oxygen relative to unprocessed powder. Hardness values for all samples was between 306.8 and 361.5 HV1. It is proposed that adding hydrogen into the build atmosphere reduced the available energy density for tungsten melting by …

Investigation Of Additively Manufactured Molybdenum-Tungsten-Rhenium Alloys, Randolph T. Abaya

Theses and Dissertations

The process of creating metal components through additive manufacturing is changing the way different industries can avoid the shortcomings of traditional metal production. Metals such as tungsten, molybdenum, and rhenium have many advantages for different applications, especially when alloyed together. In this study, an additively manufactured alloy containing 70% molybdenum, 25% tungsten, and 5% rhenium (70Mo-25W-5Re) is tested for its strength, ductility, hardness, and porosity. The 70Mo-25W-5Re alloy is printed through Laser Powder Bed Fusion (LPBF) under different conditions such as printing speed and printing atmosphere. Additionally, the effects of post printing heat treatment are conducted to understand the advantages …

Characterization Of High Cycle Fatigue And Laser-Aided Machining And Polishing Of Additively Manufactured Materials, Mohammad Masud Parvez

Doctoral Dissertations

“Additive manufacturing (AM) and laser-aided machining and polishing (LAMP) of materials are emerging manufacturing processes both for research and industrial sectors. The AM process can manufacture near-net-shape parts with complex geometries. Meanwhile, the LAMP process integrated with an AM system offers a high processing rate, minimum heat-affected zone, and easily adjustable process parameters during machining and polishing. In mechanical properties characterization of AM metals and alloys, fatigue is a vitally important test method to understand the behavior of materials in cycling loading and unloading circumstances since most mechanical failures of structures are due to fatigue. To characterize AM metal fatigue …

Printing, Characterization, And Mechanical Testing Of Additively Manufactured Refractory Metal Alloys, Brianna M. Sexton

Browse all Theses and Dissertations

Refractory metal alloys in the tungsten molybdenum rhenium ternary system were additively manufactured using laser power bed fusion. Four ternary alloys with varying concentrations of tungsten, molybdenum, and rhenium were manufactured and manufactured again with an addition of 1 wt% hafnium carbide. Samples were heat treated to heal cracks, reduce porosity, and reduce inhomogeneity. Material microstructure was characterized before and after heat treatment using microscopy, energy dispersive x-ray spectroscopy, and electron backscatter diffraction mapping. Mechanical testing was conducted on both three-point bend specimens and compression specimens, resulting in maximum bending strengths of 677.86 MPa, and maximum compression 0.2% yield strengths …

A Convolutional Neural Network (Cnn) For Defect Detection Of Additively Manufactured Parts, Musarrat Farzana Rahman

Masters Theses

“Additive manufacturing (AM) is a layer-by-layer deposition process to fabricate parts with complex geometries. The formation of defects within AM components is a major concern for critical structural and cyclic loading applications. Understanding the mechanisms of defect formation and identifying the defects play an important role in improving the product lifecycle. The convolutional neural network (CNN) has been demonstrated to be an effective deep learning tool for automated detection of defects for both conventional and AM processes. A network with optimized parameters including proper data processing and sampling can improve the performance of the architecture. In this study, for the …