Engineering Commons^™

Entrainment Processes For A Jet In Cross-Flow: The Quantification Of Turbulent Contributions And Their Importance On Accurate Modeling, Graham Asher Freedland

Dissertations and Theses

A jet in cross flow (JICF) is examined experimentally by injecting a stream of air into crossing fluid with an aim into quantifying entrainment process and downstream evolution. The behavior of JICF is important to fields ranging from turbine-blade cooling to smokestack pollution and volcanic eruption dynamics. Existing simplified volcanic plume models are tested; most importantly, the near-field contributions of complex interconnected vortex systems, which present significant uncertainties because they assume negligible turbulence. While jets in irrotational cross-flow have been investigated, this analysis has focused on the interaction between a turbulent jet in low and highly turbulent cross-flow created by …

Modeling Airflows And Voc Source Strengths For An Occupied School, Brett Stinson

University Honors Theses

Volatile organic compounds (VOCs) are a group of air pollutants that can adversely impact human health, engage in chemistry indoors, and meaningfully degrade indoor and outdoor urban air quality. While extensive research with regard to VOC emission rates from indoor sources has been conducted, it was not until recently that this work began to focus on characterizing emissions from humans and human activity in depth. As buildings are constructed to be increasingly airtight, and the materials utilized are chosen to reduce VOC emissions, it follows that human contributions are poised to become increasingly important indoor sources of VOCs. Utilizing data …

Indoor Air Quality Impacts Of A Woodstove Exchange Program In Washington County, Oregon, Matthew Forrest Survilo

Dissertations and Theses

More than six million people in the United States use wood stoves as their primary heat source. Wood stoves emit air pollutants that may impact health, e.g., wood combustion products are associated with premature death and aggravation of pulmonary and cardiovascular conditions. There are few studies investigating the efficacy of wood stove exchange programs (WSEPs) as a method to improve indoor air quality (IAQ). In partnership with Washington County Department of Health and Human Services we conducted an air quality study to measure the impact of a WSEP on indoor and neighborhood levels of wood combustion products. Twenty households engaged …

Dynamic Effects Of Inertial Particles On The Wake Recovery Of A Model Wind Turbine, Sarah E. Smith

Dissertations and Theses

Impacting particles such as rain, dust, and other debris can have devastating structural effects on wind turbines, but little is known about the interaction of such debris within turbine wakes. This study aims to characterize behavior of inertial particles within the turbulent wake of a wind turbine and relative effects on wake recovery. Here a model wind turbine is subjected to varied two-phase inflow conditions, with wind as the carrier fluid (Re_λ = 49 - 88) and polydisperse water droplets (26 to 45µm in diameter) at varied concentrations (Φ_v=0.24 x 10^-5 - 1.3 …

Droplet Ejections During Wet Lab Operations Aboard Spacecraft, Caleb Cushman Turner

Dissertations and Theses

The breakup and rupture of liquid bridges, thin films, bubbles, droplets, rivulets, and jets can produce satellite droplets that are subsequently ejected into their surrounding environment. For example, when any solid object is withdrawn from a liquid bath, the formation of an ever-thinning columnar liquid bridge eventually ruptures along the axis of the bridge. When rupture occurs under typical pipetting conditions the dynamics governing the rupture almost always produce at a minimum a satellite droplet. When these droplets occur they are often too small and too fast to be observed by the human eye. In a terrestrial environment they are …

A Numerical Investigation Of Microgravity Evaporation, Daniel Peter Ringle

Dissertations and Theses

Evaporation is important to myriad engineering processes such as cooling, distillation, thin film deposition, and others. In fact, NASA has renewed interest in using cabin air pressure evaporation as a means to recycle waste water in space. As one example, NASA recently conducted experiments aboard the International Space Station (ISS) to measure evaporation rates in microgravity and to determine the impacts of porous structure on the process. It has long been assumed that differences in evaporation rates between 1-g₀ and microgravity are small. However, discrepancies by as much as 40% have been observed in practice. The assumption now …

Characterization Of Inertial Particles In The Turbulent Wake Of A Porous Disk, Kristin Nichole Travis

Dissertations and Theses

This study presents the findings of a wind tunnel experiment investigating the behaviour of micrometric inertial particles in the turbulent wake of a stationary porous disk. Various concentrations [Φ_v ∈ (2.95 x 10^-6 - 1.22 x 10^-5)] of polydisperse water droplets (diameter 13-41 µm) are compared to sub-inertial tracer particles. Hot-wire anemometry, phase Doppler interferometry and particle image velocimetry were implemented in the near and far wake regions to study the complex dynamics of the particles. Turbulence statistics and particle size distributions are presented and used to explore the particle wake interaction.

The Optimization Of Machining Parameters For Milling Operations By Using The Nelder Mead Simplex Method, Yubin Lee

Dissertations and Theses

Machining operations need to be optimized to maximize profit for computer numerical control (CNC) machines. Although minimum production time could mean high productivity, it can not guarantee maximum profit rate in CNC milling operations. The possible range of machining parameters is limited by several constraints, such as maximum machine power, surface finish requirements, and maximum cutting force for the stability of milling operations. Among CNC machining parameters, cutting speed and feed have the greatest effect on machining operations. Therefore, cutting speed and feed are considered as main process variables to maximize the profit rate of CNC milling operations.

A variety …