Engineering Commons^™

Enhancing Fish Farming Sustainability In Guatemala: A Cost-Effective Oxygenation Solution, Olivia Wheeler, Creighton Seibeert, Carlos Gomez Gutierrez

Scholar Week 2016 - present

This project addresses a critical challenge faced by small-scale, family-owned fish farms in Guatemala, providing adequate oxygen to their fishponds due to the lack of reliable grid power and high energy costs. The primary goal is to design a sustainable and cost-effective solution that ensures continuous oxygenation within the range of 5-7 parts per million (ppm) of dissolved oxygen (DO). To achieve this, the solution must operate independently of grid power, withstand Guatemala's environmental conditions, and be replicable by local farmers for widespread accessibility. The holistic design objectives focus on boosting fish harvest yields, reducing operational costs, promoting sustainability, empowering …

Viscosity Of Adsorbent Slurries For Washcoating Applications, Nitish Chauhan

Theses and Dissertations

The viscosity of adsorbent slurries is pivotal in understanding their rheological behavior, yet, the research on adsorbent slurry viscosity has been limited. This study addresses this gap by analyzing porous and non-porous solutes' behavior in solvents and then applying it to the washcoating adsorbents on ceramic substrates. By examining MIL-101 (Cr), glass beads, silica nanoparticles, and Titania, the study aims to comprehend the viscosity variations of each solute in the solvents, water and ethanol. A key observation from this study was the significant role of wetting in determining viscosity, as initial results found that MIL-101 (Cr) exhibited the highest viscosity …

Water Hammer Analysis For Ash Slurry Disposal Pipelines Of A Thermal Power System, Biprodip Mukherjee, Subhasish Das, Satyapriya Mandal

Journal of Environmental Science and Sustainable Development

Coal-ash slurry transportation via pipelines has been accepted as a potential, economical, and dependable mode of two-phase flow of solid-liquid transportation. It is solid-liquid transportation where the ash slurry generally flows through mild steel, and a good amount of pump energy and pressure is required to convey the slurry with a density above 1220 kg/m3. The study is basically on the water hammer analysis of ash slurry conveying pipes. Nevertheless, since the hammer analysis is typically carried out in normal water, the study of ash slurry is compared to the know criteria of potable water. The study aims to understand …

Stabilization Trajectory And Recovery System For High Altitude Weather Balloon Payloads (S.T.A.R.), Robert Canalas, Aaron Juan, Miles Nguyen, James Oblitas, Anne Paloma

Mechanical Engineering Senior Theses

Of the 657,000 global balloon launches each year, only 20% of payloads are recovered, leading to unsustainable business and environmental practices. This paper details the development and evaluation of the S.T.A.R. (Stabilization, Trajectory, and Recovery) system, which increases the recovery rate of weather balloon sensors by enabling ideal landing conditions. System testing concludes that S.T.A.R. is capable of housing weather sensors in a fully controllable glider capable of targeted landing. If properly scaled up and redesigned for mass production, the S.T.A.R. system increases weather-sensing equipment recovery for weather-reporting institutions around the world. Although the featured iterations consist of basswood, carbon …

Investigation Of Fiber Orientation And Mechanical Properties Of Pyrolysis Recycled Carbon-Fiber Reinforced Thermoset Composite, Reva N. Simmons, Harry Lee, Garam Kim

Discovery Undergraduate Interdisciplinary Research Internship

With increasing demand of carbon fiber reinforced fiber thermoset composites, establishing a sustainable cycle for these materials becomes crucial. Pyrolysis is a process of reclaiming carbon fiber from thermoset composites by thermally degrading the polymer at high temperatures allowing the fibers to be extracted. Carbon fiber reclaimed through current pyrolysis processes for thermoset composites typically loses its original shape and orientation, making it difficult to reorganize the fibers. This study investigated the feasibility of maintaining the fiber orientations for continuous fiber reinforced thermoset composite during pyrolysis by stitching the carbon fiber layup to a conformable copper mesh during the manufacturing …

Part Design Geometry-Driven Toolpath Optimization For Additive Manufacturing Energy Sustainability Improvement, David Kolawole Somade

Graduate Research Theses & Dissertations

One of the most promising new manufacturing technologies in the past three decades isadditive manufacturing (AM), also commonly known as three-dimensional (3D) printing or rapid prototyping. The energy consumption problem in AM can be significant when it is adopted at the industrial scale or used under resource-restricted conditions. The energy consumption of an AM process is influenced by several factors including bed heating, filament extrusion, material infill, component cooling, etc. All these factors are further determined by the equipment and the toolpath for a specific printing task. Build orientation and tool-path direction are frequently used to optimize part and process …

Urban Farming: Empowerment To Increase Economic, Education, And Nutritional Benefit For The Sub-Urban Community, Nasruddin Nasruddin, Yusuf Donner Dwiyantama, Banu Muhammad, Anom Bowalaksono, Dian Ayubi, Sarah Islamiati Pertiwi

ASEAN Journal of Community Engagement

This article discusses the urban farming program at Sekolah Master in Beji, Depok, Indonesia, which aims to provide the community with broader benefits, such as economy, education, and increased nutritional value. The project involves planting method that was introduced to this school community. The program itself consists of several stages, starting from the preparation—dissemination of the program and designing a plan for the greenhouse, the implementation—constructing the greenhouse and installing the automatic water system, planting the vegetation, and monitoring and evaluation of the program. Eventually, an evaluation of the successful program is required to determine whether the program can be …

Synthesis And Characterization Of Hybrid Catalysts For Fischer-Tropsch Jet Fuel Production, Jack M. Steinagel

Honors College Theses

Climate change is a major issue that our world is facing today. Finding renewable options for current infrastructure is paramount to solving this issue. Fischer-Tropsch synthesis of syngas from gasified biomass can produce renewable fuels that can be used in current conventional combustion engines. In order to make this process more industrially viable, a higher selectivity towards the desired range of liquid hydrocarbon products must be achieved. A novel way to do this is to introduce a catalyst to the Fischer-Tropsch reaction. The catalyst’s physical and chemical properties can promote chain growth of specific hydrocarbons. For the purpose of this …

Aircraft Engine Particulate Matter Emissions From Sustainable Aviation Fuels: Results From Ground-Based Measurements During The Nasa/Dlr Campaign Eclif2/Nd-Max, Tobias Schripp, Bruce E. Anderson, Uwe Bauder, Bastian Rauch, Joel C. Corbin, Greg J. Smallwood, Prem Lobo, Ewan C. Crosbie, Michael A. Shook, Richard C. Miake-Lye, Zhenhong Yu, Andrew Freedman, Philip D. Whitefield, Claire E. Robinson

Chemistry Faculty Research & Creative Works

The use of alternative jet fuels by commercial aviation has increased substantially in recent years. Beside the reduction of carbon dioxide emission, the use of sustainable aviation fuels (SAF) may have a positive impact on the reduction of particulate emissions. This study summarizes the results from a ground-based measurement activity conducted in January 2018 as part of the ECLIF2/ND-MAX campaign in Ramstein, Germany. Two fossil reference kerosenes and three different blends with the renewable fuel component HEFA-SPK (Hydroprocessed Esters and Fatty Acids Synthetic Paraffinic Kerosene) were burned in an A320 with V2527-A5 engines to investigate the effect of fuel naphthalene/aromatic …

Trade-Off Characterization Between Social And Environmental Impacts Using Agent-Based Models And Life-Cycle Assessment, Joseph C. Leichty, Christopher S. Mabey, Christopher A. Mattson, John L. Salmon, Jason Weaver

Faculty Publications

Meeting the UN’s sustainable development goals requires designers and engineers to solve multi-objective optimization problems involving trade-offs between social, environmental, and economic impacts. This paper presents an approach for designers and engineers to quantify the social and environmental impacts of a product at a population-level and then perform a trade-off analysis between those impacts. In the approach, designers and engineers define the attributes of the product as well as the materials and processes used in the product’s life cycle. Agent-Based Modeling (ABM) tools that have been developed to model the social impacts of products are combined with Life- Cycle Assessment …

A Qualitative Look Into Repair Practices, Jumana Labib

Undergraduate Student Research Internships Conference

This research poster is based on a working research paper which moves beyond the traditional scope of repair and examines the Right to Repair movement from a smaller, more personal lens by detailing the 6 categorical impediments as dubbed by Dr. Alissa Centivany (design, law, economic/business strategy, material asymmetry, informational asymmetry, and social impediments) have continuously inhibited repair and affected repair practices, which has consequently had larger implications (environmental, economic, social, etc.) on ourselves, our objects, and our world. The poster builds upon my research from last year (see "The Right to Repair: (Re)building a better future"), this time pulling …

Measuring Engineering Students' Engagement In Sustainability Design Concepts, Karen Aide Perez

Boise State University Theses and Dissertations

Within industries, governments, and accreditation organizations, there has been a push to incorporate sustainability concepts into their models. Universities like Boise State University (BSU) have already begun to place greater emphasis in inclusion of sustainability concepts in different engineering department curricula. As part of this effort, BSU plans to redesign courses to integrate sustainability concepts using active learning modules (ALMs) suited for each grade level and discipline. The effectiveness of these modules will be evaluated across disciplines. In support of this larger goal, the work in this study will specifically focus on mechanical engineering students.

A survey instrument was developed …

Strategic Energy Master Planning For Carbon Neutrality, Marie Patterson

CSU Journal of Sustainability and Climate Change

Universities across the United States are generating goals to be more sustainable and carbon neutral. The energy used in existing buildings on campuses amount to a large volume of greenhouse emissions and must be reduced to help achieve neutrality goals. Strategic Energy Master Plans are instrumental to support these goals through the development of recommendations to reduce energy. Calculating the energy use intensity for existing buildings, a main component of a Strategic Energy Master Plan, can help the campus understand where energy is being used the most. With this information the highest energy consuming buildings can be the focus of …

Laptop Recycling Case Study: Estimating The Contained Value And Value Recovery Process Feasibility Of End-Of-Life Consumer Electronics, Zebulon Hart

Theses and Dissertations--Mining Engineering

Work has been done to establish, through the development and use of novel assay techniques and analysis metrics, the contained value of a sampling of laptop computers (as an analog for myriad e-waste sources). This work has conceptualized e-waste as an alternative to geologic-origin complex metallic ores and has likewise evaluated the feasibility of value recovery from e-waste sources in a similar manner to an ore. The application of conventional and novel mineral separation techniques to e-waste recycling processes has been evaluated and positive results are demonstrated. Further, this work has demonstrated the ability to identify the presence of base …

Tall Timber In Denver: An Exploration Of New Forms In Large Scale Timber Architecture, Andrew P. Weuling

Masters Theses

Wood has been utilized by humans for thousands of years in the construction of our built environment. More recently, our expanded understanding of the material and the advancement of engineered wood have allowed us to use wood like never before. Concrete and steel, however, have emerged as the main materials used in large scale construction in the late 19^th and 20^th Centuries. As we are battling and searching for solutions to climate change, the importance of wood in large scale construction has increased as not only is its carbon intensity is lower than steel and concrete, but its …

Sustainability Assessment Of Direct Energy Deposition (Ded) Based Hybrid Manufacturing Using Life Cycle Assessment (Lca) Method, Faujia Islam

Graduate Theses, Dissertations, and Problem Reports

As sustainability has emerged as a highlight for almost every field over the last few decades, the manufacturing field is no exception. Generally, additive manufacturing performs better than traditional manufacturing in terms of sustainability because of its lean energy- and material usage. Previous studies have compared the sustainability performance between traditional and additive manufacturing, but hybrid manufacturing was not focused upon much. In this paper, the life cycle assessment method is used to analyze and compare the energy consumption and environmental impact of direct energy deposition (DED) based hybrid manufacturing and traditional manufacturing “CNC milling” process for a turbine blade. …

Robust And Sustainable Energy Pathways To Reach Mexico’S Climate Goals, Rodrigo Mercado Fernandez

Doctoral Dissertations

As countries set climate change goals for adaptation and mitigation efforts, there are many questions regarding to how to reach these targets. These efforts will necessitate the transition of our electricity infrastructure from relying on conventional electricity generation technologies including natural gas, coal and oil, to clean energy generation with renewables. Through the three essays presented in this dissertation, we explore various pathways of development for the electricity system to reach long term climate change goals. We are interested in identifying: Is there a unique optimal development option or are there various? How do different mixes of electricity generation technologies …

Applying Renewable Energies Against Climate Change: Solar Photovoltaic (Pv) Energy, Juan Jose Estribi

English Language Institute

In recent years, more efforts towards fighting climate change have been done. As a direct response, research and technology have offered several insights regarding the specific causes, effects, and even possible solutions for resolving this global issue. Among these solutions, renewable energies and their potential contributions as clean energy sources can be assessed as feasible options for the energy transformation through the decarbonization process of the energy industry. This poster is mainly focused on solar photovoltaic (PV) energy and its great potential as a renewable energy by making a brief assessment of some important aspects such as resource availability, its …

Modeling Of Electrical Grid Systems To Evaluate Sustainable Electricity Generation In Pakistan, Muhammad Mustafa Amjad

Masters Theses

Pakistan has always had a history of severe energy shortfalls, which rose up to an alarming 33% in 2013. This situation was countered by investments in the energy sector through the China Pakistan Economic Corridor (CPEC), which were unfortunately largely based on brown fuels. Although beneficial in the short term, these investments do not bode well for the climate scenario of Pakistan, with various parts of the country already having experienced temperatures rise of 1-3°C. To ensure that the current situation doesn’t exacerbate and is tackled in a timely manner, this research aims to examine how the untapped potential of …

Atmospheric Water Harvester, Justin K. Lam, Jacob David, Jessica Mabry, Ben Brough

Mechanical Engineering

Atmospheric water harvesting uses the vapor-compression cycle to collect water from the moisture in the air. The system’s components include an evaporator, condenser, compressor, fan, and several expansion valves. Condensate from the air is then funneled into a receptacle, which determines the efficiency of the water harvesting system. For this senior project, the goal is to increase the efficiency of an existing atmospheric water harvester.

Utilization Of Recycled Filament For 3d Printing For Consumer Goods, Alexa Peterson

Apparel Merchandising and Product Development Undergraduate Honors Theses

The 3D printing market has been used in a wide variety of manufacturing industries including textile and apparel. Many consumers can now own a personal 3D printer at home for recreational printing. There are even websites dedicated to 3D printing patterns made by consumers. However, the materials used in the 3D printing process pose a problem for the environment due to their plastic-based nature. 3D printing is a layered process with each layer being printed depending on the layer below it for strength and stability. During the 3D printing process, great amounts of waste are produced as a result of …

An Assessment Of Renewable Energy Technology Implementation In Storrs, Connecticut: Emissions Reduction And Feasibility Of A Microgrid System At Uconn, Sophie Macdonald

Honors Scholar Theses

The purpose of this project is to design a clean energy-sourced microgrid for UConn’s main campus that would reduce the university’s energy emissions while remaining within the geographic boundaries of viable UConn-owned land. Economic cost was not considered in this analysis; instead, emissions and space constraints were the optimized measures of value and feasibility. Sources of energy that were considered include photovoltaics (PV), wind turbines, hydrokinetic systems, and fuel cells. Energy storage capacity was included in the analysis as well. The overall system was optimized first by ignoring space constraints and for a minimum of 10% reduction from the current …

Novel Methods For Composites Recycling Via Pyrolysis, Matt Jacobs

Undergraduate Honors Theses

Composites are unique materials in many respects. When fabric woven from carbon fibers is joined with a thermoset resin in a controlled environment, it results in a very strong material, especially evaluated on a pound-for-pound basis against metals and ceramics. One aspect of this construction that provides great strength lies in the fiber-matrix adhesion which facilitates load transfer to the reinforcement of the composite. This fiber-matrix adhesion is promoted by the polarity of the usual thermoset matrices, and properly designed sizing materials coating the fibers. It’s a two-edged sword, though. Although the resin and the fibers are quite strong together, …

Zips Precious Plastics: Plastic Extruder, Patrick Cole

Williams Honors College, Honors Research Projects

This project's goal was to design and build an affordable desktop filament extruder that can precisely and consistently extrude filament to a certain tolerance acceptable for 3D printers using wasted printing material. The group is partnering with an on campus organization focusing on engineering applications for sustainable futures. Zips Precious Plastics is a student run design group that intends to bring an innovation space on campus to help educate students about the importance of a closed looped system within plastic manufacturing.

Hvac System Energy Audit For Leverett Elementary School, Connor Smalling

Biological and Agricultural Engineering Undergraduate Honors Theses

Leverett Elementary School is located in Fayetteville, AR. The school needs significant upgrades to its infrastructure. The Fayetteville Public School District has voted to pursue an Energy Services Performance Contract (ESPC) in order to finance the desired upgrades to Leverett Elementary, among other schools in the district.

The scope of this thesis was to perform an energy audit on the existing heating, ventilation, and air conditioning (HVAC) system. By using an energy modeling software, eQuest, the building and the existing base system were modeled to determine utility consumption. Three different HVAC system alternatives were analyzed against the base system by …

A Discovery Of Social Impact Categories For The Sustainable Design Of Engineered Products And Their Consideration By Industry Professionals, Andrew Taylor Pack

Theses and Dissertations

Sustainable design is often practiced and assessed through the consideration of three essential areas: economic sustainability, environmental sustainability, and social sustainability. For even the simplest of products, the complexities of these three areas and their trade-offs cause decision making transparency to be lost in most practical situations. Additionally, the models and tools available to consider social sustainability are severely underdeveloped. This thesis is separated into three parts: 1) a design tool to consider all three aspects of sustainability simultaneously, 2) a literature survey to characterize social impact as it relates to products, and 3) interviews with engineering professionals regarding how …

Process Sustainability Evaluation For Manufacturing Of A Component With The 6r Application, Ana E. Bonilla Hernández, Tao Lu, Tomas Beno, Claes Fredriksson, Ibrahim S. Jawahir

Institute for Sustainable Manufacturing Faculty Publications

Sustainability in manufacturing can be evaluated at product, process and system levels. The 6R methodology for sustainability enhancement in manufacturing processes includes: reduced use of materials, energy, water and other resources; reusing of products/components; recovery and recycling of materials/components; remanufacturing of products; and redesigning of products to utilize recovered materials/resources. Although manufacturing processes can be evaluated by their productivity, quality and cost, process sustainability assessment makes it a complete evaluation. This paper presents a 6R-based evaluation method for sustainable manufacturing in terms of specific metrics within six major metrics clusters: environmental impact, energy consumption, waste management, cost, resource utilization and …

Designing And Redesigning Products, Processes, And Systems For A Helical Economy, Ryan Bradley, Ibrahim S. Jawahir

Institute for Sustainable Manufacturing Faculty Publications

The Circular Economy (CE) concept has promised to unlock trillions of dollars in business value while driving a significant reduction in the world’s resource consumption and anthropogenic emissions. However, CE mainly lives in ambiguity in the manufacturing domain because CE does not address the changes needed across all of the fundamental elements of manufacturing: products, processes, and systems. Conceptually, CE is grounded in the concept of closed-loop material flows that fit within ecological limits. This grounding translates into a steady state economy, a result that is not an option for the significant portion of the world living in poverty. Therefore, …

Toward Building Resilient, Sustainable, And Smart Infrastructure In The 21st Century, Aly Mousaad Aly

Faculty Publications

In recent years, as a result of significant climate change, stringent windstorms are becoming more frequent than before. Given the threat that windstorms bring to people and property, wind/structural engineering research is imperative to improve the resilience of existing and new infrastructure, for community safety and assets protection. The Windstorm Impact, Science and Engineering (WISE) research program at Louisiana State University (LSU) focuses on creating new knowledge applicable to the mitigation of existing and new infrastructure, to survive and perform optimally under natural hazards. To achieve our research goals, we address two imperious challenges: (i) characterization of realistic wind forces …

The Correlation Between Energy Cost Share, Human, And Economic Development Using Time Series Data From Australasia, Europe, North America, And The Brics Nations, Ryan Roberts, Josephine Kaviti Musango, Alan Colin Brent, Matthew K. Heun

University Faculty Publications and Creative Works

This paper investigates how a change in a region's energy cost share (ECS), a ratio of a region's energy expenditure as a fraction of its gross domestic product (GDP), affects the region's social and economic development. Nations from four regions of the world, namely Australasia, Europe, North America, and the BRICS nations (Brazil, Russia, India, China, and South Africa) were chosen for this study. Using time series data from the period of 1978 to 2010, the annual ECS of each country was compared to the year-on-year GDP change, as well as the components of the human development index (HDI). High …