Engineering Commons^™

Studies Of Damage Tolerance In Automated Fiber Placement Based Heterogeneous Meso-Architectured Carbon/ Epoxy Composite Laminates., Karan Kodagali

Theses and Dissertations

Traditional unidirectional (UD) carbon fiber-reinforced polymer matrix composites manufactured via automated fiber placement (AFP) are widely used in aerospace structures. While heterogeneous at the micro-scale, these materials are homogeneous at the meso-scale (ply-scale). The major limitation is its limited toughness, poor damage tolerance/impact resistance capability and the inability to sufficiently redistribute stresses, resulting in strength-toughness tradeoffs, making them susceptible to impact damage. From previous studies, there is an understanding that fiber architecture has a first order effect on the damage tolerance. Introducing new discontinuous/heterogeneous meso-scale architectures, through an optimal merger of material and structure, can result in unprecedented property improvements …

The Effect Of Through Thickness Reinforcement Angle On The Disbonding Behavior In Skin-Stringer Configuration, Christopher John Morris

Mechanical & Aerospace Engineering Theses & Dissertations

Post-cure through thickness reinforcement is a method used to increase the mechanical properties of composite laminates in the transverse direction. This study conducted a test on skin-stringer structures bonded together in three configurations using an epoxy or thermoplastic adhesive at the interface with reinforcing pins inserted through the laminate thickness located at the edge of the stringer at differing angles between -30º and 30º. The fabrication of these samples in configurations B and C consisted of the use of carbon fiber prepeg laminate at a ply orientation of [0₂90₂]_2s for the skin and [0 90] …

Establishing Physical And Chemical Mechanisms Of Polymerization And Pyrolysis Of Phenolic Resins For Carbon-Carbon Composites, Ivan Gallegos, Josh Kemppainen, Jacob R. Gissinger, Malgorzata Kowalik, Adri Van Duin, Kristopher E. Wise, S. Gowtham, Gregory Odegard

Michigan Tech Publications, Part 2

The complex structural and chemical changes that occur during polymerization and pyrolysis critically affect material properties but are difficult to characterize in situ. This work presents a novel, experimentally validated methodology for modeling the complete polymerization and pyrolysis processes for phenolic resin using reactive molecular dynamics. The polymerization simulations produced polymerized structures with mass densities of 1.24 ± 0.01 g/cm3 and Young's moduli of 3.50 ± 0.64 GPa, which are in good agreement with experimental values. The structural properties of the subsequently pyrolyzed structures were also found to be in good agreement with experimental X-ray data for the phenolic-derived carbon …

Investigation Of Fatigue Response With Analytical And Machine Learning Models And Hygroscopic Analysis Of Asymmetric Bistable Cfrp Composites, Shoab Ahmed Chowdhury

All Dissertations

Asymmetric bistable carbon fibre reinforced plastic (CFRP) composites enable a broad range of applications as they can sustain multiple stable configurations and have small snap-through load requirements. These unique features, coupled with their light strength-to-weight and stiffness-to-weight ratios, have made them preferred options for multifunctional systems. This study investigates the fatigue and hygroscopic response of 2-ply, [0/90] bistable CFRP laminates and proposes predictive modeling approaches for improved performance.

While previous studies widely researched and documented the fatigue of general composites in axial loading, fatigue analysis of asymmetric bistable composites in the out-of-plane snap-through direction is inadequate. This study performs fatigue …

Chemical And Physical Interaction Mechanisms And Multifunctional Properties Of Plant Based Graphene In Carbon Fiber Epoxy Composites, Daniel W. Mulqueen

Mechanical & Aerospace Engineering Theses & Dissertations

Graphene has generated substantial interest as a filler due to its exceptional strength, flexibility, and conductivity but faces obstacles in supply and implementation. A renewable, plant-based graphene nanoparticle (pGNP) presents a more accessible and sustainable filler with the same properties as mineral graphenes. In this study, the mechanisms of graphene reinforcement in carbon fiber reinforced plastic (CFRP) were examined, along with the resulting improvements to mechanical strength, resistance to crack propagation, electrical and thermal conductivity at elevated temperatures. pGNP, produced from renewable biomass, was shown to have a graphitic structure with flakes 3-10 layers thick and a median lateral size …

Northrop Grumman Collaboration Project, Nikkia Psomas-Sheridan, Santiago Robles, Ben Elkayam, Benjamin Ulfhake

Mechanical Engineering

The Northrop Grumman Collaboration Project (NGCP) is a collaborative club project sponsored by Northrop Grumman for the students of Cal Poly San Luis Obispo (CPSLO) and Cal Poly Pomona (CPP) to create a fleet of vehicles to aid in the simulated rescue of stranded hiker. The CPSLO club is responsible for delivering an autonomous flight vehicle that can suppress a fire and retrieve a payload. Mechanical Design Team of the CPSLO team was responsible for the design of the frame, electronics housing, and payload and fire suppression systems.

The Modernization Of Large Power Transformer Tanks, Babajide O. Williams

Electronic Theses and Dissertations

Due to the current demands placed on the power grid in terms of climate change, increasing urbanization, and terrorist attacks, the U.S. government in response to these demands, mandated that all the grid components be modernized in order to increase their reliability. As a critical component of the grid, Large Power Transformers (LPTs) play a key role in ensuring sustainable power generation and distribution. A literature search performed in this work and the analysis of data retrieved from the search showed that the tanks of these LPTs are critical to their durability, longevity, and reliability. Therefore, the reliability of LPTs …

A Predictive Analysis Of The Influence Of Thickness And Length On The Curvature Of Square Bistable Carbon Fiber Reinforced Composite Laminates, Stephan Terry

All Theses

This thesis presents a predictive analysis of the stability of square bistable carbon fiber reinforced composite laminates under various loading conditions. The stability of these laminates is essential to their performance and longevity and is influenced by factors such as thickness and length. Analytical and numerical techniques are used to model the behavior of these laminates, and experimental tests are conducted to validate the models. The findings of this research have implications for the design and optimization of square bistable carbon fiber reinforced composites.

The study investigates the relationships between the side length and thickness of square laminates for bistability. …

Fusion Bonding Behavior Of 3d Printed Pa6/Cf Composites Via Post Fabrication Compaction, Gonzalo Fernandez Mediavilla

Mechanical & Aerospace Engineering Theses & Dissertations

Additive manufacturing (AM) is becoming a robust production technology for aerospace, healthcare, and construction industries among others. Fused Deposition Modelling (FDM) is one of the methods most used to 3D print products. FDM has limitation due to interlayer adhesion and restriction imposed by the printing direction. Specially with AM composites, as reinforced nylon PA6 with short fibers, parts show more strength along the direction of the filament due to the alignment of the carbon fibers, but weaker in other directions. The proposed method to solve this issue is to print parts separately and join them together by fusion bonding. PA6/CF …

Shape Memory Polymer-Based Multifunctional Syntactic Foams, Siavash Sarrafan

LSU Doctoral Dissertations

With the increase in popularity of shape memory polymers (SMPs), especially in applications such as aerospace, textile, biomedical engineering, and even structures, the weight of the material and the devices made with it has always been a crucial factor. Using the shape memory polymer as a matrix to make a syntactic foam is one of the best and most affordable approaches to creating a lighter material that still has the shape memory effect. The addition of particles of different stiffness, strength, and size, with variable fractions, creates a composite that enables engineering the mechanical, as well as other physical and …

Anisotropic Material Behavior Of 3d Printed Fiber Composites, Jordan Garcia

Theses and Dissertations--Mechanical Engineering

Literature has shown that 3D printed composites may have highly anisotropic mechanical properties due to variation in microstructure as a result of filament deposition process. Laminate composite theory, which is already used for composite products, has been proposed as an effective method for quantifying these mechanical characteristics. Starting with the analysis of comparing the printing orientation of premanufactured carbon fiber reinforced filament, the mechanical properties of 3D printed objects were examined. The mechanical properties changed not only as a result of machine choice, but how the sample is oriented along the printing bed. The analysis continued with looking at the …

Northrop Grumman Collaboration Project, Nikkia Rae Psomas-Sheridan, Santiago Robles, Ben Elkayam, Benjamin Ulfhake

Mechanical Engineering

The Northrop Grumman Collaboration Project (NGCP) is a collaborative club project sponsored by Northrop Grumman for the students of Cal Poly San Luis Obispo (CPSLO) and Cal Poly Pomona (CPP) to create a fleet of vehicles to aid in the simulated rescue of stranded hiker. The CPSLO club is responsible for delivering an autonomous flight vehicle that can suppress a fire and retrieve a payload. Mechanical Design Team of the CPSLO team was responsible for the design of the frame, electronics housing, and payload and fire suppression systems.