Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 9 of 9
Full-Text Articles in Engineering
Laser Metal Deposition Of An Alcocrfeniti₀.₅ High-Entropy Alloy Coating On A Ti6al4v Substrate: Microstructure And Oxidation Behavior, Wenyuan Cui, Wei Li, Wei Ting Chen, Frank W. Liou
Laser Metal Deposition Of An Alcocrfeniti₀.₅ High-Entropy Alloy Coating On A Ti6al4v Substrate: Microstructure And Oxidation Behavior, Wenyuan Cui, Wei Li, Wei Ting Chen, Frank W. Liou
Mechanical and Aerospace Engineering Faculty Research & Creative Works
Ti6Al4V has been recognized as an attractive material, due to its combination of low density and favorable mechanical properties. However, its insufficient oxidation resistance has limited the high-temperature application. In this work, an AlCoCrFeNiTi0.5 high-entropy alloy (HEA) coating was fabricated on a Ti6Al4V substrate using laser metal deposition (LMD). The microstructure and isothermal oxidation behaviors were investigated. The microstructure of as-deposited HEA exhibited a Fe, Cr-rich A2 phase and an Al, Ni, Ti-enriched B2 phase. Its hardness was approximately 2.1 times higher than that of the substrate. The oxidation testing at 700⁰C and 800⁰C suggested that the HEA coating …
Fabrication And Characterization Of Alₓcrcufeni₂ High-Entropy Alloys Coatings By Laser Metal Deposition, Wenyuan Cui, Xinchang Zhang, Lan Li, Yitao Chen, Tan Pan, Frank W. Liou
Fabrication And Characterization Of Alₓcrcufeni₂ High-Entropy Alloys Coatings By Laser Metal Deposition, Wenyuan Cui, Xinchang Zhang, Lan Li, Yitao Chen, Tan Pan, Frank W. Liou
Mechanical and Aerospace Engineering Faculty Research & Creative Works
High-entropy alloys (HEAs) are becoming new hot spots in the metallic materials community, which are defined to contain equiatomic or close-to-equiatomic compositions. HEAs can possess many interesting mechanical properties, and in particular, they have the great potential to be used as coating materials requiring high hardness and wear resistance. In this study, the feasibility of fabrication AlₓCrCuFeNi₂ (x=0,0.75) HEAs was investigated via laser metal deposition from elemental powders. The microstructure, phase structure, and hardness were studied by an optical microscope, scanning electron microscopy with energy dispersive spectroscopy (SEM/EDS), electron backscatter diffraction (EBSD) and Vickers hardness tester. The bonding between the …
On The Feasibility Of Tailoring Copper-Nickel Functionally Graded Materials Fabricated Through Laser Metal Deposition, Sreekar Karnati, Yunlu Zhang, Frank W. Liou, Joseph William Newkirk
On The Feasibility Of Tailoring Copper-Nickel Functionally Graded Materials Fabricated Through Laser Metal Deposition, Sreekar Karnati, Yunlu Zhang, Frank W. Liou, Joseph William Newkirk
Mechanical and Aerospace Engineering Faculty Research & Creative Works
In this study, pulse‐width modulation of laser power was identified as a feasible means for varying the chemical gradient in copper—nickel‐graded materials. Graded material deposits of 70 wt. %. copper‐30 wt. %. nickel on 100 wt. %. nickel and vice versa were deposited and characterized. The 70/30 copper—nickel weight ratio in the feedstock powder was achieved through blending elemental copper and 96 wt. %. Ni—Delero‐22 alloy. At the dissimilar material interface over the course of four layers, the duty cycle of power was ramped down from a high value to optimized deposition conditions. This change was theorized to influence the …
Fabrication Of Alcocrfeni High-Entropy Alloy Coating On An Aisi 304 Substrate Via A Cofe₂Ni Intermediate Layer, Wenyuan Cui, Sreekar Karnati, Xinchang Zhang, Elizabeth Burns, Frank W. Liou
Fabrication Of Alcocrfeni High-Entropy Alloy Coating On An Aisi 304 Substrate Via A Cofe₂Ni Intermediate Layer, Wenyuan Cui, Sreekar Karnati, Xinchang Zhang, Elizabeth Burns, Frank W. Liou
Mechanical and Aerospace Engineering Faculty Research & Creative Works
Through laser metal deposition, attempts were made to coat AlCoCrFeNi, a high-entropy alloy (HEA), on an AISI 304 stainless steel substrate to integrate their properties. However, the direct coating of the AlCoCrFeNi HEA on the AISI 304 substrate was found to be unviable due to cracks at the interface between these two materials. The difference in compositional change was suspected to be the source of the cracks. Therefore, a new transition route was performed by coating an intermediate layer of CoFe2Ni on the AISI 304 substrate. Investigations into the microstructure, phase composition, elemental composition and Vickers hardness were …
Effect Of Optimizing Particle Size In Laser Metal Deposition With Blown Pre-Mixed Powders, Wei Li, Jingwei Zhang, Xinchang Zhang, Sreekar Karnati, Frank W. Liou
Effect Of Optimizing Particle Size In Laser Metal Deposition With Blown Pre-Mixed Powders, Wei Li, Jingwei Zhang, Xinchang Zhang, Sreekar Karnati, Frank W. Liou
Mechanical and Aerospace Engineering Faculty Research & Creative Works
Functionally Graded Material (FGM) is often fabricated by Laser metal deposition with pre-mixed multiple powders (PMM-powder). Since the supplied PMM-powder directly affects FGM’s composition, investigation on PMM-powder’s property is greatly needed. This paper employed experimental method to observe an important problem: PMM-powder separation in fabricating FGM. A novel particle size optimization method was introduced as solution to eliminate the powder separation. Pre-mixed pure Cu and 4047 Al powders were used to do two experiments. The first experiment result disclosed the existence of powder separation. By optimizing the particle size, the PMM-powder separation was effectively solved in the second experiment result.
Defects Classification Of Laser Metal Deposition Using Acoustic Emission Sensor, Haythem Gaja, Frank W. Liou
Defects Classification Of Laser Metal Deposition Using Acoustic Emission Sensor, Haythem Gaja, Frank W. Liou
Mechanical and Aerospace Engineering Faculty Research & Creative Works
Laser metal deposition (LMD) is an advanced additive manufacturing (AM) process used to build or repair metal parts layer by layer for a range of different applications. Any presence of deposition defects in the part produced causes change in the mechanical properties and might cause failure to the part. In this work, defects monitoring system was proposed to detect and classify defects in real time using an acoustic emission (AE) sensor and an unsupervised pattern recognition analysis. Time domain and frequency domain, and relevant descriptors were used in the classification process to improve the characterization and the discrimination of the …
A Smooth Toolpath Generation Method For Laser Metal Deposition, Renwei Liu, Zhiyuan Wang, Yunlu Zhang, Todd E. Sparks, Frank W. Liou
A Smooth Toolpath Generation Method For Laser Metal Deposition, Renwei Liu, Zhiyuan Wang, Yunlu Zhang, Todd E. Sparks, Frank W. Liou
Mechanical and Aerospace Engineering Faculty Research & Creative Works
Laser metal deposition (LMD), also known as direct metal deposition (DMD) or laser engineered net shaping (LENS), which uses a laser beam to form a melt pool on a metallic substrate, into which powder or wire is fed. The conventional contour and zigzag toolpath pattern for LMD are discontinuous at turn points or corner points. The discontinuous toolpath causes uneven deposition, which brings height variation and porosity problems. This paper aims to develop a smooth toolpath generation method for LMD to improve the deposition quality. A parametric curve equation based on trigonometric functions is derived and built. It can be …
Effect Of Powder Particle Size On The Fabrication Of Ti-6al-4v Using Laser Metal Deposition From Elemental Powder Mixture, Xueyang Chen, Lei Yan, Wei Li, Frank W. Liou, Joseph William Newkirk
Effect Of Powder Particle Size On The Fabrication Of Ti-6al-4v Using Laser Metal Deposition From Elemental Powder Mixture, Xueyang Chen, Lei Yan, Wei Li, Frank W. Liou, Joseph William Newkirk
Mechanical and Aerospace Engineering Faculty Research & Creative Works
Direct LMD (laser metal deposition) was used to fabricate thin-wall Ti-6Al-4V using the powder mixture of Ti-6 wt.%Al-4 wt.%V. SEM (scanning electron microscopy), OM (optical microscopy) and EDS (energy dispersive spectroscopy) were employed to examine the chemical composition and microstructure of the as-deposited sections. Vickers hardness tests were then applied to characterize the mechanical properties of the deposit samples which were fabricated using pre-mixed elemental powders. The EDS line scans indicated that the chemical composition of the samples was homogenous across the deposit. After significant analysis, some differences were observed among two sets of deposit samples which varied in the …
Dc-Gain Layer-To-Layer Stability Criterion In Laser Metal Deposition Processes, Patrick M. Sammons, Douglas A. Bristow, Robert G. Landers
Dc-Gain Layer-To-Layer Stability Criterion In Laser Metal Deposition Processes, Patrick M. Sammons, Douglas A. Bristow, Robert G. Landers
Mechanical and Aerospace Engineering Faculty Research & Creative Works
In Laser Metal Deposition (LMD), a blown powder metal additive manufacturing process, functional metal parts are fabricated in a layer-by-layer fashion. In addition to the in-layer dynamics, which describe how the process evolves within a given layer, the additive-fabrication property of LMD creates a second set of dynamics which describe how the process evolves from layer-to-layer. While these dynamics, termed layer-to-layer dynamics, are coupled with both the in-layer dynamics and the process operating conditions, they are not widely considered in the modeling, process planning, or process control of LMD operations. Because of this, seemingly valid choices for process parameters can …