Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 9 of 9
Full-Text Articles in Engineering
Experimental Investigation Of Additive Manufacturing Of Continuous Carbon Fiber Composites With Multifunctional Electro-Tensile Properties, Ritesh Ghimire, Frank W. Liou
Experimental Investigation Of Additive Manufacturing Of Continuous Carbon Fiber Composites With Multifunctional Electro-Tensile Properties, Ritesh Ghimire, Frank W. Liou
Mechanical and Aerospace Engineering Faculty Research & Creative Works
Manufacturing processes for monofunctional and multifunctional materials vary depending on the design optimization. Multifunctional continuous carbon fiber composites provide great potential in achieving coupled structural and electrical properties for their applications in aircraft, unmanned aircraft systems, and spacecraft. Proper optimization of tensile and electrical properties offers benefits early in the design and continuous operational safety phases to obtain coupled multifunctional properties. In this paper, fused filament fabrication additive manufacturing (AM) technique was used to fabricate continuous carbon fiber solid laminated composites test coupons. The proposed new method characterizes the electrical conductivity's coupled effects on the tensile properties, including the failure …
Additive Manufacturing Of Stainless Steel -- Copper Functionally Graded Materials Via Inconel 718 Interlayer, Xinchang Zhang, Lan Li, Frank W. Liou
Additive Manufacturing Of Stainless Steel -- Copper Functionally Graded Materials Via Inconel 718 Interlayer, Xinchang Zhang, Lan Li, Frank W. Liou
Mechanical and Aerospace Engineering Faculty Research & Creative Works
The joining of dissimilar materials is becoming increasingly prevalent to integrate different material properties to enhance design flexibility and overall performance. This study introduced an innovative approach to additively manufacture copper on 316L stainless steel (SS316L) via Inconel 718 interlayers using directed energy deposition (DED). The novel multi-material structure was studied both experimentally and theoretically. The microstructure, tensile properties, microhardness, and thermal performance of the structure were characterized. Residual stress distribution over the structure was revealed by experimental-validated numerical modeling. The result exhibits that defect-free structures with excellent interfacial bonding can be achieved by introducing Inconel 718 interlayers. The bonding …
A Novel Laser-Aided Machining And Polishing Process For Additive Manufacturing Materials With Multiple Endmill Emulating Scan Patterns, Mohammad Masud Parvez, Sahil Patel, Sriram Praneeth Isanaka, Frank W. Liou
A Novel Laser-Aided Machining And Polishing Process For Additive Manufacturing Materials With Multiple Endmill Emulating Scan Patterns, Mohammad Masud Parvez, Sahil Patel, Sriram Praneeth Isanaka, Frank W. Liou
Mechanical and Aerospace Engineering Faculty Research & Creative Works
In additive manufacturing (AM), the surface roughness of the deposited parts remains significantly higher than the admissible range for most applications. Additionally, the surface topography of AM parts exhibits waviness profiles between tracks and layers. Therefore, post-processing is indispensable to improve surface quality. Laser-aided machining and polishing can be effective surface improvement processes that can be used due to their availability as the primary energy sources in many metal AM processes. While the initial roughness and waviness of the surface of most AM parts are very high, to achieve dimensional accuracy and minimize roughness, a high input energy density is …
The Effect Of Nanostructures In Aluminum Alloys Processed Using Additive Manufacturing On Microstructural Evolution And Mechanical Performance Behavior, Rachel Boillat, Sriram Praneeth Isanaka, Frank W. Liou
The Effect Of Nanostructures In Aluminum Alloys Processed Using Additive Manufacturing On Microstructural Evolution And Mechanical Performance Behavior, Rachel Boillat, Sriram Praneeth Isanaka, Frank W. Liou
Mechanical and Aerospace Engineering Faculty Research & Creative Works
This paper reviews the status of nanoparticle technology as it relates to the additive manufacturing (AM) of aluminum-based alloys. A broad overview of common AM processes is given. Additive manufacturing is a promising field for the advancement of manufacturing due to its ability to yield near-net-shaped components that require minimal post-processing prior to end-use. AM also allows for the fabrication of prototypes as well as economical small batch production. Aluminum alloys processed via AM would be very beneficial to the manufacturing industry due to their high strength to weight ratio; however, many of the conventional alloy compositions have been shown …
Experimental And Numerical Investigation In Directed Energy Deposition For Component Repair, Lan Li, Xinchang Zhang, Frank W. Liou
Experimental And Numerical Investigation In Directed Energy Deposition For Component Repair, Lan Li, Xinchang Zhang, Frank W. Liou
Mechanical and Aerospace Engineering Faculty Research & Creative Works
Directed energy deposition (DED) has been widely used for component repair. In the repair process, the surface defects are machined to a groove or slot and then refilled. The sidewall inclination angle of the groove geometry has been recognized to have a considerable impact on the mechanical properties of repaired parts. The objective of this work was to investigate the feasibility of repairing various V-shaped defects with both experiments and modeling. At first, the repair volume was defined by scanning the defective zone. Then, the repair volume was sliced to generate the repair toolpath. After that, the DED process was …
Fabrication Of Silicon Nitride Parts By Ceramic On-Demand Extrusion Process, Sachin Choudhary
Fabrication Of Silicon Nitride Parts By Ceramic On-Demand Extrusion Process, Sachin Choudhary
Masters Theses
“Ceramic On-Demand Extrusion (CODE) is a patented solid freeform fabrication method for manufacturing high-density monolithic ceramic parts. In the past 5-6 years, the technology has been successfully implemented to fabricate alumina and zirconia parts. The mechanical characterizations also show CODE’s high potential in achieving desired structural properties. The present study covers the fabrication of silicon nitride parts by CODE process, which entailed the design of paste formulation for achieving rheology suitable for dimensional control in fabricated parts and determining firing temperature and the content of sintering additives for silicon nitride green bodies fabricated by CODE. The density, hardness, and fracture …
Additively Manufactured Metallic Cellular Structures, Okanmisope Aziel Fashanu
Additively Manufactured Metallic Cellular Structures, Okanmisope Aziel Fashanu
Doctoral Dissertations
"Cellular structures are lightweight structures with excellent mechanical, thermal, and acoustic properties. They offer promise in a series of applications, including lightweight applications, sandwich cores, mechanical damping, acoustic absorption, strain isolation, and thermal management. The manufacturing of these complex cellular structures is expensive and time-consuming, which hinders the adoption of these structures in many industries. Advancement in manufacturing technologies, such as additive manufacturing (AM), however, have changed this. AM allows for the rapid and less expensive manufacturing of complex cellular structures. This work aimed to investigate the performance of additively manufactured cellular structures for lightweight and sandwich core applications. In …
Layer-To-Layer Feedback Control For Direct Energy Deposition Additive Manufacturing, Michelle Gegel
Layer-To-Layer Feedback Control For Direct Energy Deposition Additive Manufacturing, Michelle Gegel
Doctoral Dissertations
"Additive manufacturing (AM) has garnered much attention in recent years, some calling it the fourth industrial revolution. It was first used to create rapid prototypes, although recent efforts have been made to advance the technology towards production of functional parts. This requires advancement in the materials used in AM, as well as the ability to produce quality parts repeatably. More specifically, direct energy deposition (DED) of metal powders is a process capable of producing and repairing parts with complex geometries; however, it is not widely used in industry due to challenges with quality control. In this process, metal powder is …
Fabrication, Characterization Of High-Entropy Alloys And Deep Learning-Based Inspection In Metal Additive Manufacturing, Wenyuan Cui
Doctoral Dissertations
"Alloying has been used to confer desirable properties to materials. It typically involves the addition of small amounts of secondary elements to a primary element. In the past decade, however, a new alloying strategy that involves the combination of multiple principal elements in high concentrations to create new materials called high- entropy alloys (HEAs) has been in vogue. In the first part, the investigation focused on the fabrication process and property assessment of the additive manufactured HEA to broaden its engineering applications. Additive manufacturing (AM) is based on manufacturing philosophy through the layer-by-layer method and accomplish the near net-shaped components …