Engineering Commons^™

Investigation Of Low Reynolds Number Flow And Heat Transfer Of Louvered Surfaces, Pradeep R. Shinde

FIU Electronic Theses and Dissertations

This study focuses on the investigation of flow behavior at low Reynolds numbers by the experimental and numerical performance testing of micro-channel heat exchangers. An experimental study of the heat transfers and pressure drop of compact heat exchangers with louvered fins and flat tubes was conducted within a low air-side Reynolds number range of 20 < Re_Lp < 225. Using an existing low-speed wind tunnel, 26 sample heat exchangers of corrugated louver fin type, were tested. New correlations for Colburn j and Fanning friction f factor have been developed in terms of non-dimensional parameters. Within the investigated parameter ranges, it seems that both the j and f factors are better represented by two correlations in two flow regimes (one for Re_Lp = 20 – 80 and one for Re_Lp = 80 – 200) than a single regime correlation in the power-law format. The results support the conclusion that airflow and heat transfer at very low Reynolds numbers behaves differently from that …

Management Optimization Of Energy Consumption Reduction For Residential Hot Water, Francesco Cataldi

FIU Electronic Theses and Dissertations

The objective of this thesis is to create an automatic water management system capable of optimizing the usage of warm water stored in two water tanks to reduce the monthly energy consumption of the instant water heater installed in a residential house. This system is called Water Mixing System (WMS). The two heat sources considered are: PV-T system and heat rejected by the air condition system. The PV-T system is a new technology that allows transformation of the sun radiation into both electricity and warm water, increasing the efficiency of the panel compared to either a common photovoltaic panel or …

Computational Fluid Dynamic Analysis Of Microbubble Drag Reduction Systems At High Reynolds Number, John D. Goolcharan

FIU Electronic Theses and Dissertations

Microbubble drag reduction (MBDR) is an effective method to improve the efficiency of fluid systems. MBDR is a field that has been extensively studied in the past, and experimental values of up to 80% to 90% drag reduction have been obtained. The effectiveness and simplicity of MBDR makes it a viable method for real world applications, particularly in naval applications where it can reduce the drag between the surface of ships and the surrounding water. A two dimensional single phase model was created in ANSYS Fluent to effectively model the behavior of bubble laden flow over a flat plate. This …

Database-Assisted Analysis And Design Of Wind Loads On Rigid Buildings, Filmon Fesehaye Habte

FIU Electronic Theses and Dissertations

The turbulent nature of the wind flow coupled with additional turbulence created by the wind-building interaction result in highly non-uniform, fluctuating wind-loading on building envelopes. This is true even for simple rectangular symmetric buildings. Building codes and standards should reflect the information on which they are based as closely as possible, and this should be achieved without making the building codes too complicated and/or bulky. However, given the complexity of wind loading on low-rise buildings, its codification can be difficult, and it often entails significant inconsistencies. This required the development of alternative design methods, such as the Database-Assisted-Design (DAD) methodology, …

Mens Doped Adhesive And Influence On Fracture Toughness, Kao Z. Yang

FIU Electronic Theses and Dissertations

Composites are in high demand; however, fasteners are often required for joining process and can reduce their advantages. One solution is adhesive bonding, but uncertainty exists regarding long term durability and the ability to interrogate bonds noninvasively. One potential solution to qualify bond integrity over its service life is to dope an adhesive with magneto-electric nanoparticles (MENs). MENs can yield output magnetic signatures that are influenced by bond quality and damage state. In this study, adhesives have been doped with MENs prior to bonding at 1% volume concentration. For optimum implementation, this health monitoring system should be evaluated for effects …

Characterization Of Homogenized Mechanical Properties Of Porous Ceramic Materials Based On Their Realistic Microstructure, Siavash Rastkar

FIU Electronic Theses and Dissertations

The recent advances in the Materials Engineering have led to the development of new materials with customized microstructure in which the properties of its constituents and their geometric distribution have a considerable effect on determination of the macroscopic properties of the substance. Direct inclusion of the material microstructure in the analysis on a macro level is challenging since spatial meshes created for the analysis should have enough resolution to be able to accurately capture the geometry of the microstructure. In most cases this leads to a huge finite element model which requires a substantial amount of computational resources.

To circumvent …