Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 7 of 7
Full-Text Articles in Engineering
Open Source Low-Cost Power Monitoring System, Shane W. Oberloier, Joshua M. Pearce
Open Source Low-Cost Power Monitoring System, Shane W. Oberloier, Joshua M. Pearce
Department of Materials Science and Engineering Publications
This study presents an entirely open-source, low-cost power monitoring system capable of many types of measurements including both loads and supplies such as solar photovoltaic systems. In addition, the system can be fabricated using only open source software and hardware. The design revolves around the Digital Universal Energy Logger (DUEL) Node, which is responsible for reading and properly scaling the voltage and current of a particular load, and then serializing it via an on-board ATTiny85 chip. The configuration of the DUEL node allows for custom sensitivity ranges, and can handle up to 50 A and 300 V. Up to 127 …
Approaches To Open Source 3-D Printable Probe Positioners And Micromanipulators For Probe Stations, Iiro Hietanen, Ismo T. S. Heikkinen, Hele Savin, Joshua M. Pearce
Approaches To Open Source 3-D Printable Probe Positioners And Micromanipulators For Probe Stations, Iiro Hietanen, Ismo T. S. Heikkinen, Hele Savin, Joshua M. Pearce
Department of Materials Science and Engineering Publications
Three types of highly-customizable open source probe positioning systems are evaluated: (a) mostly 3-D printed, (b) partially printed using OpenBeam kinematic constraints, and (c) a 3-level stack of low-cost commercial single axis micropositioners and some printed parts. All systems use digital distributed manufacturing to enable bespoke features, which can be fabricated with RepRap-class 3-D printer and easily accessible components. They are all flexible in material choice for custom components. The micropositioners can be set up for left-right use and flat or recessed configurations using either mechanical or magnetic mounting. All systems use a manual probe holder that can be customized …
Reprapable Recyclebot: Open Source 3-D Printable Extruder For Converting Plastic To 3-D Printing Filament, Aubrey Woern, Joseph Mccaslin, Adam Pringle, Joshua M. Pearce
Reprapable Recyclebot: Open Source 3-D Printable Extruder For Converting Plastic To 3-D Printing Filament, Aubrey Woern, Joseph Mccaslin, Adam Pringle, Joshua M. Pearce
Department of Materials Science and Engineering Publications
In order to assist researchers explore the full potential of distributed recycling of post-consumer polymer waste, this article describes a recyclebot, which is a waste plastic extruder capable of making commercial quality 3-D printing filament. The device design takes advantage of both the open source hardware methodology and the paradigm developed by the open source self-replicating rapid prototyper (RepRap) 3-D printer community. Specifically, this paper describes the design, fabrication and operation of a RepRapable Recyclebot, which refers to the Recyclebot’s ability to provide the filament needed to largely replicate the parts for the Recyclebot on any type of RepRap 3-D …
Design Optimization Of Polymer Heat Exchanger For Automated Household-Scale Solar Water Pasteurizer, David C. Denkenberger, Joshua M. Pearce
Design Optimization Of Polymer Heat Exchanger For Automated Household-Scale Solar Water Pasteurizer, David C. Denkenberger, Joshua M. Pearce
Department of Materials Science and Engineering Publications
A promising approach to reducing the >870,000 deaths/year globally from unsafe water is flow-through solar water pasteurization systems (SWPs). Unfortunately, demonstrated systems have high capital costs, which limits access for the poor. The most expensive component of such systems is the heat exchanger (HX). Thus, this study focuses on cost optimization of HX designs for flow-through SWPs using high-effectiveness polymer microchannel HXs. The theoretical foundation for the cost optimization of a polymer microchannel HX is provided, and outputs are plotted in order to provide guidelines for designers to perform HX optimizations. These plots are used in two case studies: (1) …
Development Of A Resilient 3-D Printer For Humanitarian Crisis Response, Benjamin L. Savonen, Tobias Mahan, Maxwell W. Curtis, Jared W. Schreier, John K. Greshonen, Joshua M. Pearce
Development Of A Resilient 3-D Printer For Humanitarian Crisis Response, Benjamin L. Savonen, Tobias Mahan, Maxwell W. Curtis, Jared W. Schreier, John K. Greshonen, Joshua M. Pearce
Department of Materials Science and Engineering Publications
Rapid manufacturing using 3-D printing is a potential solution to some of the most pressing issues for humanitarian logistics. In this paper, findings are reported from a study that involved development of a new type of 3-D printer. In particular, a novel 3-D printer that is designed specifically for reliable rapid manufacturing at the sites of humanitarian crises. First, required capabilities are developed with design elements of a humanitarian 3-D printer, which include, (1) fused filament fabrication, (2) open source self-replicating rapid prototyper design, (3) modular, (4) separate frame, (5) protected electronics, (6) on-board computing, (7) flexible power supply, and …
Open Source Database And Website To Provide Free And Open Access To Inactive U.S. Patents In The Public Domain, Yuenyong Nilsiam, Joshua M. Pearce
Open Source Database And Website To Provide Free And Open Access To Inactive U.S. Patents In The Public Domain, Yuenyong Nilsiam, Joshua M. Pearce
Department of Materials Science and Engineering Publications
Although theoretically the patent system is meant to bolster innovation, the current United States Patent and Trademark Office (USPTO) is cumbersome and involves a significant time investment to locate inactive patents less than 20 years old. This article reports on the development of an open source database to find these public domain ideas. First, a search strategy is explained. Then the operation and use of free and open source software are detailed to meet the needs of open hardware innovators. Finally, a case study is presented to demonstrate the utility of the approach with 3-D printing. The results showed how …
Open Source Laser Polymer Welding System: Design And Characterization Of Linear Low-Density Polyethylene Multilayer Welds, John Laureto, Serguei V. Dessiatoun, Michael M. Ohadi, Joshua M. Pearce
Open Source Laser Polymer Welding System: Design And Characterization Of Linear Low-Density Polyethylene Multilayer Welds, John Laureto, Serguei V. Dessiatoun, Michael M. Ohadi, Joshua M. Pearce
Department of Materials Science and Engineering Publications
The use of lasers to weld polymer sheets provides a means of highly-adaptive and custom additive manufacturing for a wide array of industrial, medical, and end user/consumer applications. This paper provides an open source design for a laser polymer welding system, which can be fabricated with low-cost fused filament fabrication and off-the-shelf mechanical and electrical parts. The system is controlled with free and open source software and firmware. The operation of the machine is validated and the performance of the system is quantified for the mechanical properties (peak load) and weld width of linear low density polyethylene (LLDPE) lap welds …